Résumé du contenu de la page N° 17
activated at the vehicle, you can toggle the feature on simultaneously pressing the Lock + Option buttons of the transmitter. The 24 hour icon will appear and the transmitter will emit a tone confirming the feature is active. Note: the unit will start once and run for the prescribed time. If you require more frequent starting please refer to auto start up timer mode shown earlier in this guide. NOTE: To insure accurate 24 Hour Start up, it is advisable to reset the start time periodically as ti
Résumé du contenu de la page N° 18
Battery Indicator: Your transmitter has a battery indicator that is shown in the upper right corner of the screen as shown left. This icon indicates a new battery shown with 3 bars. As the battery deteriorates, the bars will disap- pear. 1 bar indicates the battery should be replaced. Replace battery with a fresh 1.5V AAA battery and dispose of the used battery properly. Other icons that will be displayed at times when certain functions and features are active in the vehicle or on the remote:
Résumé du contenu de la page N° 19
Page 19 128-7863 19 of 20
Résumé du contenu de la page N° 20
XR9000 SYSTEM FUNCTIONS AT A GLANCE DASH LED INDICATORS RAPID FLASHING = PASSIVE ARMING/ACTIVE REARMING SLOW FLASHING = ARMED OFF = DISARMED ON SOLID = VALET MODE 3 FLASH...PAUSE = INTRUSION ZONE 3 2 FLASH...PAUSE = INTRUSION ZONE 2 1 FLASH...PAUSE = INTRUSION ZONE 1 SIREN CHIRP INDICATORS 1 CHIRP * = ARM 2 CHIRPS * = DISARM 3 CHIRPS = ARM / DOOR OPENED 4 CHIRPS = DISARM / INTRUSION * These chirps are optional, and can be de - activated. PARKING LAMP INDICATORS 1 FLASH = ARM 2 FLASHES = DISARM 3
Résumé du contenu de la page N° 1
Model XR9000
Owner’s Manual
Long Range Remote Start Security System
With Plug-In Shock Sensor & Starter Disable
IMPORTANT ! In order to provide you with the highest level of security to your
vehicle, this system is equipped with selectable manual override circuitry. It is
possible that you will need to override you security system if the transmitter
becomes lost, or inoperative due to battery failure. Reading the sections on
"Manually Overriding Your System" is necessary to fully understand
Résumé du contenu de la page N° 2
Additional Engine Immobilizer Output, (Optional Relay Required) True Last Door Arming (Hardwire Only) Defective Zone By-Pass Defective Zone Chirp Confirmation (Unit Chirps To Report Zone Cleared) 6 Tone Mini Siren Car Horn Output For Additional Alarm Response (Improved Timing To Minimize RF Interference.) Additional Negative Trigger Input (Hood and Trunk) RF Inhibit With Ignition On Parking Light Flasher (Relay On Board) Plug In Dual Stage Shock Sensor (Pre-detect, Full Trigger and “Ci
Résumé du contenu de la page N° 3
simply press button 1, (lock), two times within a one second time period. The system will now respond to that transmitter each time a button is pressed. NOTE: This system is custom configurable and can be set up to operate with a number of options controlled from any transmitter button or button com- bination. For reference, we will describe operation assuming that your system is programmed for separate lock and unlock but- tons. Also reference will be made to the icons as shown on the button
Résumé du contenu de la page N° 4
Doors Lock - Optional NOTE: If the optional Headlamp illumination feature has been added, and has been selected for operation when arming, as an added convenience, the sys- tem will turn on the headlights when the system is armed. The LCD Remote has the following response: ARMING THE SYSTEM - PASSIVE (AUTOMATIC) (Must be activated during programming) 1. Turn off the engine, exit the vehicle and close and lock all doors, hood lid and trunk lid. The dash mounted LED begins to flash rapidly, indi
Résumé du contenu de la page N° 5
transmitter button is activated, the drivers door only will unlock, pressing the unlock button a second time will cause all doors to unlock. NOTE: If your transmitter has been configured with single button Lock/Unlock, to activate the all door unlock feature operate the Lock/Unlock button a second time within 3 seconds of the first unlock command. 1. As you approach the vehicle, press and release the Unlock/Disarm button on the keychain transmitter. The dash mounted LED turns off. The LED will
Résumé du contenu de la page N° 6
WARNING SIGNALS section of this manual to identify which zone was triggered. Doors Unlock - Optional 2 Step Doors Unlock - Optional NOTE: If the optional Headlamp illumination feature has been added and has been selected for operation when disarming, as an added convenience, the system will turn on the headlights when the system is disarmed. WHILE THE SYSTEM IS SOUNDING If during a triggered state, you wish to shut off the siren without disarming your security system, simply press and release
Résumé du contenu de la page N° 7
1. Open the vehicle door. The alarm will sound. 2. Turn the ignition key to the on position. 3. Within 5 seconds, press and release the PBLED override switch. The alarm system will stop sounding and enter the (bypassed) mode. You can now start and operate the vehicle normally. Typically this override mode is used only if the transmitter has become inopera- tive. Programming Your Custom Override Code: Unlike override switches easily found, and defeated, this security system allows the consum
Résumé du contenu de la page N° 8
(As per the example, press and release 2 times to set the units digit to 2). 8. Turn the ignition switch to the off position. Immediately observe the LED flash pattern. You will note the LED flashing five times, pause, and then flash two times, pause. This pattern will be repeated three times indicating the new code (52) has been accepted and stored in memory. NOTE: If after step 7, the LED flashes a code other than what was just entered, this indicates that the code has not been changed. You w
Résumé du contenu de la page N° 9
again for 3 seconds. If the button is not pressed, the alarm will automatically stop after 30 seconds. Also if any transmitter button other than the Lock or Unlock button is pressed and released, the Panic mode will be turned off immediately. The normal function of this transmitter button will be suspended during the Panic sounding period. 3. During the panic mode, the Lock and Unlock buttons can be used to lock and unlock the doors, (if the option is installed), however once the unlock/disarm
Résumé du contenu de la page N° 10
programmed, simply press the lock button of your keychain transmitter anytime during the remote start cycle. The shock sensor will be shunted for the entire run cycle and will resume normal operation after the remote start unit shuts off. Check with your installation center to determine if this feature has been pro- grammed into your system. PBLED SAFETY CONTROL SWITCH The Push-Button LED control switch allows you to temporarily disable the remote starting function of the system. This recommend
Résumé du contenu de la page N° 11
2. Depress the brake pedal. 3. Open the hood. 4. Place the system in the Remote Start Override mode. 5. Race the engine to above 4000 RPM. OPERATING ON AUTOMATIC START UP TIMER MODE Your system has the ability to automatically start the vehicle every 2 or 4 hours over a 48 hour period. This feature is especially useful in cold climates where the only means to keep the engine and engine fluids warm is to periodically start the engine. WARNING! Be certain that the vehicle is outdoors before using
Résumé du contenu de la page N° 12
NOTE: The feature that has been added to channel 3 will always be activated using the same transmitter button that remotely starts the vehicle. There is no way to move the channel 3 function to a different transmitter button. ADDITIONAL REMOTE FUNCTION (CHANNEL 4) This system has an additional feature that can be connected to a number of different optional accessories. Some of the more common uses for this channel are: Can Be Set Up To Activate Rear Window Defogger During Remote Start If Vehi
Résumé du contenu de la page N° 13
1) Place the gear selector in park. 2) Set the parking, (hand), brake. 3) Be certain your foot is off the brake pedal. 4) Press the program/Push-Button switch 2 times within 5 seconds. The parking lights will flash two times indicating the mode was successfully en- tered. If your parking lights flashed four times, this indicates the turbo mode was on and is now turned off. With the turbo timer mode selected on, after you've arrived at your destination, while the engine is still running, set the
Résumé du contenu de la page N° 14
When the Panic Mode has been activated and the system is armed the vehicle's lights will flash, the siren and lock icon will be displayed on the LCD screen and the siren will beep. If the system is disarmed and the Panic Mode is activated, the lights will flash unlock icon will be displayed and the siren will beep on the LCD screen. When ever the vehicle is operated from the two way transmitter, the unit will beep responsive to the function executed at the vehicle. 1 beep when armed, 2 beeps wh
Résumé du contenu de la page N° 15
the door is closed or the zone clears, the transmitter will chirp 1 time, and the display will clear. When the vehicle is armed, and the hood or trunk, is opened or ajar, the transmitter will chirp 3 times, the lights will flash, and the display will indicate a hood or trunk trigger as shown on the previous page. When the hood or trunk is closed, or the zone clears, the transmit- ter will chirp 1 time, and the display will clear. Page 15 128-7863 15 of 20
Résumé du contenu de la page N° 16
ADDITIONAL REMOTE FEATURES: The two way remote control unit allows you to access status information from the vehicle, check temperature, light the display, toggle the transmitter from beep tones to vibrate mode, initiate daily start timer, and temperature start. Selection of these and other features are shown below: NOTE: Transmitter must be within operating range of the vehicle, approximately 1000 ft. Check Vehicle Status: Press the lock+key+option buttons simultaneously for 1 second. The vehi
