Instruction d'utilisation Cisco Systems OL-24281-01

Instruction d'utilisation pour le dispositif Cisco Systems OL-24281-01

Dispositif: Cisco Systems OL-24281-01
Catégorie: Système domestique de protection
Fabricant: Cisco Systems
Dimension: 5.9 MB
Date d'addition: 5/9/2013
Nombre des pages: 84
Imprimez l'instruction

Téléchargez

Comment utiliser?

Notre objectif consiste à vous assurer le plus rapide accès au contenu de l'instruction d'utilisation du dispositif Cisco Systems OL-24281-01. En utilisant l'aperçu en ligne vous pouvez parcourir le sommaire et passer à la page où vous trouverez la résolution de votre problème avec Cisco Systems OL-24281-01.

Pour votre confort

Si regarder l'instruction Cisco Systems OL-24281-01 directement sur la page n'est pas confortable pour vous, vous pouvez profiter de deux solutions possibles:

  • Exploration au mode de plein écran - pour analyser l'instruction d'une manière commode (sans l'avoir téléchargée sur votre ordinateur) vous pouvez utiliser le mode d'exploration en plein écran. Pour démarrer l'exploration de l'instruction Cisco Systems OL-24281-01 en plein écran, utilisez le bouton Plein écran.
  • Téléchargement sur l'ordinateur - vous pouvez aussi télécharger l'instruction Cisco Systems OL-24281-01 sur votre ordinateur et la sauvegarder dans vos ressources. Si vous n'avez pas envie de gaspiller votre espace disque, vous pouvez toujours télécharger cette instruction du ManualsBase dans l'avenir.
Cisco Systems OL-24281-01 Manuel d'utilisation - Online PDF
Advertisement
« Page 1 of 84 »
Advertisement
Version imprimée

Beaucoup de gens préfèrent de lire les documents dans la version imprimée et non pas sur l'écran. L'option d'impression de l'instruction est aussi prévue et vous pouvez en profiter en cliquant le lien ci-dessus - Imprimez l'instruction. Il n'est pas nécessaire d'imprimer toute l'instruction Cisco Systems OL-24281-01 - on peut choisir des pages. Economisez le papier.

Résumés

Vous trouverez ci-dessous les annonces des contenus qui se trouvent sur les pages suivantes de l'instruction de Cisco Systems OL-24281-01. Si vous voulez parcourir rapidement le contenu des pages suivantes de l'instruction, vous pouvez en profiter.

Résumés du contenu
Résumé du contenu de la page N° 1


Cisco Video Surveillance IP PTZ Dome
Camera User Guide
Cisco 2900 Series IP Dome
Americas Headquarters
Cisco Systems, Inc.
170 West Tasman Drive
San Jose, CA 95134-1706
USA
http://www.cisco.com
Tel: 408 526-4000
800 553-NETS (6387)
Fax: 408 527-0883
Text Part Number: OL-24281-01

Résumé du contenu de la page N° 2

THE SPECIFICATIONS AND INFORMATION REGARDING THE PRODUCTS IN THIS MANUAL ARE SUBJECT TO CHANGE WITHOUT NOTICE. ALL STATEMENTS, INFORMATION, AND RECOMMENDATIONS IN THIS MANUAL ARE BELIEVED TO BE ACCURATE BUT ARE PRESENTED WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED. USERS MUST TAKE FULL RESPONSIBILITY FOR THEIR APPLICATION OF ANY PRODUCTS. THE SOFTWARE LICENSE AND LIMITED WARRANTY FOR THE ACCOMPANYING PRODUCT ARE SET FORTH IN THE INFORMATION PACKET THAT SHIPPED WITH THE PRODUCT AND ARE

Résumé du contenu de la page N° 3

CONTENTS Preface vii Overview vii Organization vii Obtaining Documentation and Submitting a Service Request vii CHAPTER 1 Installation 1-1 Overview 1-1 Mounting 1-1 In-Ceiling 1-2 Pendant 1-3 Wiring 1-4 Installing the Dome Drive 1-8 Installing the Lower Dome 1-9 In-Ceiling 1-10 Pendant 1-10 Switch Settings 1-11 CHAPTER 2 Operation 2-1 System Requirements 2-1 Accessing the IP Device 2-2 Live Video Page 2-2 Live Video Page Icons 2-2 PTZ Controls 2-3 Sele

Résumé du contenu de la page N° 4

Contents Changing the Device Name 2-8 Configuring the Time Settings 2-8 Customizing the Appearance of the Text Overlay 2-9 Generating a System Log 2-9 Rebooting the Camera 2-9 Restoring All Camera Defaults 2-9 Network Tab 2-10 Changing the Hostname 2-11 Turning On DHCP 2-11 Turning Off DHCP 2-12 Selecting the Secure Sockets Layer Mode 2-13 Generating a Certificate Request 2-13 Generating a Self-Signed Certificate 2-14 Enabling Secure Shell 2-15 Selecting SNMP Settin

Résumé du contenu de la page N° 5

Contents Selecting the Users and Groups Settings 2-38 Creating a New User 2-39 Editing a User 2-40 Deleting a User 2-40 Events Tab 2-40 Creating a System Event Source 2-41 Creating a Timer Event Source 2-41 Editing an Event Source 2-42 Deleting an Event Source 2-42 Creating an Event Handler: Send Email 2-42 Creating an Event Handler: Upload JPEG to FTP Server 2-43 Editing an Event Handler 2-44 Deleting an Event Handler 2-44 Example Handler Filter Setup 2-44 INDEX Ci

Résumé du contenu de la page N° 6

Contents Cisco Video Surveillance IP PTZ Dome Camera User Guide, Cisco 2900 Series IP Dome vi OL-24281-01

Résumé du contenu de la page N° 7

Preface Overview This document, Cisco Video Surveillance IP PTZ Dome Camera User Guide, provides information about installing, configuring, and using the Cisco Video Surveillance 2900 Series Standard Definition IP PTZ cameras. Organization This manual is organized as follows: Chapter 1, “Installation” Provides instructions for installing the Cisco 2900 Series IP Dome cameras Chapter 2, “Operation” Describes how to operate the Cisco 2900 IP Dome camera Appendix A, “Troubleshooting” Provides

Résumé du contenu de la page N° 8

Preface Cisco Video Surveillance IP PTZ Dome Camera User Guide, Cisco 2900 Series IP Dome viii OL-24281-01

Résumé du contenu de la page N° 9

CH A P T E R 1 Installation This chapter provides instructions for installing the Cisco 2900 Series IP Dome cameras. This chapter includes these topics: • Overview, page 1-1 � Mounting, page 1-1 � Installing the Dome Drive, page 1-8 � Installing the Lower Dome, page 1-9 � Switch Settings, page 1-11 Overview The Cisco 2900 Series IP Dome cameras are designed with ease of installation and ease of maintenance in mind. Each camera consists of three components: a back box, a dome drive, and a

Résumé du contenu de la page N° 10

Chapter 1 Installation Mounting In-Ceiling Step 1 Prepare the ceiling (see Figure 1-1): a. Locate the center point of the mounting location, and insert the compass tool into the ceiling. b. Place the end of a pencil in the hole on the end of the compass tool, and draw a circle. c. Cut out the circle. Figure 1-1 Preparing the Ceiling d. Attach a conduit fitting (not supplied), lock nut (not supplied), and safety chain bracket (see Figure 1-2). Figure 1-2 Attaching the Conduit Fitting, Lo

Résumé du contenu de la page N° 11

Chapter 1 Installation Mounting Step 4 Pull the wiring into the back box through the conduit fitting. Step 5 Connect all required wiring (see the “Wiring” section on page 1-4). Step 6 Install the back box by compressing the spring clips and pushing the back box through the hole. Step 7 Tighten the screws until you hear a clicking noise. Pendant Step 1 Install the mount for the pendant dome. See the instructions supplied with the mount. Note If the mount is outdoors, make sure it is proper

Résumé du contenu de la page N° 12

Chapter 1 Installation Mounting Wiring Step 1 Open the hinged door to the back box by pushing the tab lock toward the wall of the unit and lifting the door open (see Figure 1-4). Figure 1-4 Black Box Door Step 2 Remove the TXB-N from the back box circuit board (see Figure 1-5): a. Loosen the captive screw on the TXB-N. b. Carefully unplug the TXB-N from the back box circuit board. Figure 1-5 Removing the TXB-N + - Cisco Video Surveillance IP PTZ Dome Camera User Guide, Cisco 2900 Series

Résumé du contenu de la page N° 13

Chapter 1 Installation Mounting 1 RJ-45 Connector 7 Standoff 2 Ethernet Cable 8 UTP Connector 3 Video Coaxial Cable 9 Back Box Circuit Board 4 16-Pin Connector 10 Audio Connectors 5 Heat Sink Standoff 11 TXB-N 6 Captive Screw Step 3 Connect the auxiliary, alarm, and other wiring to the back box circuit board (see Figure 1-6). Note Aux 1: Maximum 2 A at low voltage (<40 V). Aux 2: Maximum 30 mA at 32 VDC. If you are installing an environmental back box in a railway application, attac

Résumé du contenu de la page N° 14

Chapter 1 Installation Mounting Note To take full advantage of the distance and noise immunity benefits of audio, you must use a 600-ohm impedance matching transformer and twisted pair cable (see Figure 1-7). A stable power supply is required for optimal audio performance. Figure 1-7 Connecting Audio to the TXB-N 1 Microphone 5 Line-Out Audio Twisted Pair Cable 2 Amplifier 6 600-Ohm Impedance Matching Transformer 3 600-Ohm Impedance Matching Transformer 7 Amplifier 4 Line-In Audio Twi

Résumé du contenu de la page N° 15

Chapter 1 Installation Mounting Warning An electrical short in the back box may occur if the metal BNC connector on the video coaxial cable is not completely covered by the protective boot. Step 7 Perform one of the following options: � View video using both analog and IP connections—Connect the video coaxial cable from the back box circuit board to the coaxial cable coming in from the outside. Make sure that the BNC connector is completely covered by the protective boot. � View vide

Résumé du contenu de la page N° 16

Chapter 1 Installation Installing the Dome Drive Table 1-1 shows the maximum distances for video coaxial cable types. A cable must meet these requirements: � 75-ohm impedance � All-copper center conductor � All-copper braided shield with 95 percent braid coverage Table 1-1 Video Coaxial Cable Requirements Cable Type Maximum Distance RG59/U 750 ft (229 m) RG6/U 1,000 ft (305 m) RG11/U 1,500 ft (457 m) Table 1-2 shows the recommended maximum distances for 24 VAC and 24 VDC applications

Résumé du contenu de la page N° 17

Chapter 1 Installation Installing the Lower Dome Note When connecting more than one Cisco 2900 Series IP Dome to a single controller, terminate the unit farthest from the controller. To terminate the dome drive set the SW2-10 switch to the ON position. Figure 1-9 Setting the DIP Switches Step 2 Install the dome drive. Caution Improper installation of the dome drive can be dangerous and can seriously damage the equipment. a. Align the blue and red tabs with the blue and red labels on the

Résumé du contenu de la page N° 18

Chapter 1 Installation Installing the Lower Dome In-Ceiling Step 1 Snap the clip on the end of the trim ring leash into the hole on the lip of the back box (see Figure 1-10). Figure 1-10 Installing the In-Ceiling Lower Dome Step 2 Snap the trim ring into the plastic snap washers on the mounting screws. Pendant Step 1 Attach the back box leash to the lower dome (see Figure 1-11). Figure 1-11 Attaching the Leash to the Pendant Lower Dome Step 2 Push the lower dome into the back box. Cisco V

Résumé du contenu de la page N° 19

Chapter 1 Installation Switch Settings Step 3 Tighten the captive Phillips pan head screws to secure the lower dome (see Figure 1-12). Figure 1-12 Installing the Pendant Lower Dome Switch Settings Table 1-3 shows SW2 switch settings. Note If you are using Pelco D-type or Pelco P-type control, your system may not operate if the baud rate and address switches are not set correctly. The switches are set at the factory using the defaults for Pelco D-type control (2400 baud and address 1). T

Résumé du contenu de la page N° 20

Chapter 1 Installation Switch Settings Table 1-3 Switch Settings for SW2 (continued) Pelco D or Pelco P Protocol Baud Rate Switch Number 1 2 3 4 5 6 7 8 9 10 2400 Baud (Default for D-type Control) OFF OFF OFF 4800 Baud (Default for P-type Control) ON OFF OFF 9600 Baud OFF ON OFF Video Cable Type Switch Number 1 2 3 4 5 6 7 8 9 10 Coaxial Cable OFF Dome Termination Switch Number 1 2 3 4 5 6 7 8 9 10 Terminated ON Not Terminated OFF Table 1-4 shows SW1 switch settings for Pelco P-Type contr


Instructions pareilles
# Instruction d'utilisation Catégorie Téléchargez
1 Cisco Systems Cisco Asa 5505 10-User Bundle ASA5505BUNK9 Manuel d'utilisation Système domestique de protection 323
2 Cisco Systems 4300E Manuel d'utilisation Système domestique de protection 3
3 Cisco Systems H.323 VC-289 Manuel d'utilisation Système domestique de protection 0
4 Cisco Systems 15454-FTF2 Manuel d'utilisation Système domestique de protection 1
5 Cisco Systems ASA 5500 Manuel d'utilisation Système domestique de protection 20
6 Cisco Systems Cisco Asa 5505 10-User Bundle ASA 5505BUNK9 Manuel d'utilisation Système domestique de protection 10
7 Cisco Systems Cisco Asa 5505 10-User Bundle ASA 5505 Manuel d'utilisation Système domestique de protection 31
8 Cisco Systems ONS 15454 SDH Manuel d'utilisation Système domestique de protection 1
9 Cisco Systems OL-5742-01 Manuel d'utilisation Système domestique de protection 0
10 Cisco Systems WVC80N Manuel d'utilisation Système domestique de protection 77
11 Cisco Systems IPS4510K9 Manuel d'utilisation Système domestique de protection 2
12 Cisco Systems Cisco 5505 Adaptive Security Appliance ASA5505K8RF Manuel d'utilisation Système domestique de protection 24
13 3Com 1000BASE-T-GBIC Manuel d'utilisation Système domestique de protection 0
14 Sony BRCSDP12 Manuel d'utilisation Système domestique de protection 3
15 3Com TECHD-0000000122 Manuel d'utilisation Système domestique de protection 1
16 Sony SSC-M354 Manuel d'utilisation Système domestique de protection 3
17 Sony DIGITAL 8 DCR-TRV130E Manuel d'utilisation Système domestique de protection 9