Résumé du contenu de la page N° 1
AD-01 Slave
Auto Dialer
Owner’s Manual
AD-01 Slave Manual.indd 1 10/15/2009 10:20:44 AM
Résumé du contenu de la page N° 2
2 3 AD-01 Slave Manual.indd 2 10/15/2009 10:20:44 AM
Résumé du contenu de la page N° 3
Features: Programmable entry/exit delay time; select up to 9 (32 digit) user programmable phone numbers for each alarm; different 10 second recordable message for each alarm; built-in tamper switch; built-in terminal block for alarm and siren connection; DC adaptor with battery back-up; pro- grammable as silent alarm (dialer only) or audible (siren + dialer). Contents: 1 - Auto Dialer 1 - 12V DC Adaptor 1 - Installation & Programming Guide 1 - Telephone Cable 1 - Back-up Battery 2 3 AD-01 Sla
Résumé du contenu de la page N° 4
Installation Figure 1 Tools needed: Small Phillips Screwdriver; Large Phillips Screwdriver; Small Standard Screwdriver. Set Up: 1. Install the back-up battery (included) into the auto dialer. Use a small Phillips screwdriver to remove screw above battery cover (Figure 1-2). Remove cover by sliding downwards. Plug in battery pack making sure not to force onto pins incorrectly. Put battery pack in space provided, close battery cover, and replace the 1 4 5 3
Résumé du contenu de la page N° 5
Figure 2 (from Figure 1-1) TAMPER ALARM: The tamper alarm is alarmed when the button on the back of the dialer TAMP TR2 TR1 OV 12V+ (Figure 1-3) is depressed. If the tamper output is to be used it is important to be sure the button is depressed when the unit is mounted. The tamper terminals can be connected to any existing Trig 1 12V security system or alarm that accepts a normally Trig 2 closed input trigger. If the tamper output is not connected to any system, the jumper wire must rem
Résumé du contenu de la page N° 6
Advanced Operations How T o program TH e aUT o D Ialer *If no key is pressed for 30 seconds, the dialer will automatically exit the programming mode. Notice: The system must be in the OFF mode for all programming. How to record the voice messages: Alarm 1 = Trigger 1. Alarm 2 = Trigger 2. 1. Key in the four digit user password code (factory default is 1234.) 2. Press RECORD. 3. Press 1 (to save as the message for alarm 1) or 2 (to save as the message for alarm 2). 4. Press ENTER to start re
Résumé du contenu de la page N° 7
How to program phone numbers: You can enter a maximum of nine telephone numbers for the alarms. Each number can be a maximum of 32 digits. (If you are using this Auto Dialer on an office/work phone system you may have to enter 9 before the number to get a line out.) 1. Key in the four digit user password code (factory default is 1234.) 2. Press PROGRAM > 3 > ENTER. 3. The number you press next will select the position in the sequence you want that telephone number to dial (1 = first number
Résumé du contenu de la page N° 8
How to designate telephone numbers to alarm 1 and alarm 2: 1. Key in the four digit user password code (factory default 1234.) 2. Press PROGRAM > 6 > ENTER. 3. Press X (X = 1 for alarm 1; 2 for alarm 2). Press ENTER. 4. Press N (N = 1 for first phone number; 2 for second phone number, etc.). Press ENTER. 5. Repeat the process to designate any other numbers to each alarm. Quick guide: Press 1 2 3 4 > PROGRAM > 6 > ENTER > X > ENTER > N > ENTER How to change the user password code (factory
Résumé du contenu de la page N° 9
How to program the a uto Dialer to give an audible alarm as well as sending a voice message (factory default is alarm o N): 1. Key in the four digit user password code (factory default 1234.) 2. Press PROGRAM > 1 > ENTER 3. Press N (N = 0 for without audible alarm, 1 for with audible alarm). Press ENTER. Quick guide: Press 1 2 3 4 > PROGRAM > 1 > ENTER > N > ENTER How to set the time the alarm will sound on activation (default time is 3 minutes): 1. Key in the four digit user password code
Résumé du contenu de la page N° 10
How to set entry/exit Delay times (default both delay set at 30 seconds): The entry/exit times are the times the Auto Dialer gives you to enter/exit the area covered by the system before it arms/alarms. These are pre-set to 30 seconds. You can also change the timing to instant or 60 seconds. Entry Delay: 1. Key in the four digit user password code (factory default 1234.) 2. Press PROGRAM > 4 > ENTER 3. Press N (N = 0 for instant; 3 for 30 seconds; 6 for 60 seconds). Press ENTER. Quick guid
Résumé du contenu de la page N° 11
How T o opera Te THe aUT o D Ialer How to a rm the a larm System/Turn the Dialer o N: 1. Check that the voice message and at least one phone number has been programmed into the Auto Dialer. 2. Press 1 2 3 4 > ENTER. The Auto Dialer will show ‘ON’ on the display. 3. The alarms will become active after the delay time you have set has expired. Quick guide: Press 1 2 3 4 > ENTER How to disarm the a larm System/Turn Dialer o FF: To disarm the Alarm System or to stop the Dialer from dialing out a
Résumé du contenu de la page N° 12
How to stop the Dialer from dialing the telephone numbers in sequence: When the Auto Dialer starts dialing, it will dial the first telephone number and repeat the pre-recorded voice message for 1 minute. If there is no response from the phone, then it will hang up and dial the next number until all the programmed numbers for that alarm are dialed. It will repeat this dial sequence three times and display ‘NO ANSWER’ if there is no response from any of the phone numbers. To stop this dial seq
Résumé du contenu de la page N° 13
How T o re SeT THe aUT o D Ialer Inside the battery compartment: Remove the power supply and the Auto Dialer from the wall. Remove the 9V battery. Inside the battery compartment is a switch. Move it to the ERASE position. Connect the power to the Auto Dialer then press DELETE twice. There will be 2 short beeps from the Auto Dialer. Switch the power off again. Place switch back to NORMAL. Replace the 9V battery and place back onto the wall. Power the Auto Dialer back up. The Auto Dialer will
Résumé du contenu de la page N° 14
aD-01 Quick reference p rogramming (For step-by-step programming, refer to pages 6-10) programming: Enter Pass code 1234; push the Program button; select option number; 1 - Audible Alarm (N = 1-Audible; 0-Silent) 1234>PROGRAM>1>ENTER>N>ENTER 2 - Length of Audible Alarm (N = 1-99 Mins) 1234>PROGRAM>2>ENTER>N>ENTER 3 - Add Numbers (N = 1-9 order in which numbers are dialed) 1234>PROGRAM>3>ENTER>N>ENTER>PHONE NUMBER>ENTER Delete Numbers (N = 1-9 order in which numbers are dialed)
Résumé du contenu de la page N° 15
TECHNICAL SUPPORT If you encounter any difficulty in the operation of this product after reading the manual, please contact us. You can reach us by phone at 605-356-2772 from 8:30 AM to 5:00 PM Monday through Friday (Central Standard Time). We will be happy to answer your questions and help you in any way we can. WARRANTY Dakota Alert warrants this product to be free of defects in material and workmanship for a period of one year from the date of purchase. This warranty does not cover damage
Résumé du contenu de la page N° 16
Dakota Alert, Inc. Phone: (605) 356-2772 32556 E. Main Street Fax: (605) 356-3662 P0 Box 130 Web: www.dakotaalert.com Elk Point, SD 57025 AD-01 Slave Manual.indd 16 10/15/2009 10:20:45 AM
