Instruction d'utilisation Universal LITEAIDE HE-100BW

Résumé du contenu de la page N° 1

OWNER'S
MANUAL
PREASSEMBLED AUTOMATIC
SECURITY FLOODLIGHTS
MOTION SENSOR SECURITY
LIGHTING SYSTEMS
®
LiteAide
HE-100B
HE-100BW
HE-112
HE-112W
HE-117
HE-117W
HE-117-2B

Résumé du contenu de la page N° 2

OWNER'S MANUAL Also regard the following considerations: FLOOD LAMPS (BULBS)  The security floodlight operates on 110-120 volt, 60 Hertz electrical power only. Do not Your security floodlight uses two 150 watt (maximum) incandescent, quartz or halogen connect it to any other voltage source. flood lamps. if you are replacing an old floodlight  Locate the security floodlight at least 8 feet installation, save the flood lamps. If you are (2.5 meters) above the ground. making a new installation, o

Résumé du contenu de la page N° 3

3. Observe three controls on the sensor. CAUTION Rotate SENS/RANGE (sensitivity) control Never allow sunlight to shine fully clockwise. Rotate DAYLIGHT/TEST- directly into the security floodlight ON control fully counterclockwise. Rotate sensor prior to, during or after TIME (Time Delay) control fully installation. Direct sunlight could counterclockwise. damage the sensor. 2. Remove the preassembled security floodlight from the box. ADJUST SENS DAYLIGHT TIME RANGE TEST-ON TIME

Résumé du contenu de la page N° 4

Connect the security floodlight only to 110-120 volt, 60 Hertz electrical power. There is sufficient voltage and current to harm you if you come into contact with the 110-120 volt, 60 Hertz electrical power. BLACK 1. Turn off all electrical power to the old floodlight as follows: WARNING WHITE Ensure that the 110-120 volt, 60 Hertz electrical power to the old floodlight is OFF. There is BARE WIRE sufficient voltage and current to harm you if you come into contact with the 110-120 volt, 60 Hertz

Résumé du contenu de la page N° 5

ADJUSTMENTS AND TESTING BLACK WHITE Four easy adjustment and testing steps put BARE your security floodlight into operation: sensor and floodlight positioning, test, timing adjustment and sensitivity adjustment. You can make these adjustments and tests in daylight. GREEN (IF SUPPLIED) After a few days of operation, you may want to make readjustments - refer to FINAL ADJUSTMENTS. Sensor and Floodlight Positioning Position the sensor for correct operation and position the floodlights to light th

Résumé du contenu de la page N° 6

3. After the correct position has been Timing Adjustment established, tighten the elbow joint screw and the sensor head locknut at the end of The floodlight on-time is variable from 5 the elbow (near the cover). seconds to approximately 18 minutes. Set the on-time as follows: Screw the lamps into the sockets. 1. Turn the TIME control clockwise to the desired setting. The mid-setting is 9 minutes (approx.). The further it is turned clockwise, the longer the security floodlight remains on when tri

Résumé du contenu de la page N° 7

The floodlight remains on the set time between mode much the same as in 5 seconds and 18 minutes (approximate). the manual mode when a wall switch is installed. The manual mode permits you to turn the security floodlight on for as long a time period Set the circuit breaker as you desire. You end the on-time by manually controlling power to the turning the security floodlight off and then back security floodlight to off and on after 5 seconds (the security floodlight is then immediately on (in le

Résumé du contenu de la page N° 8

LIMITED 5 YEAR WARRANTY Universal Security Instruments, Inc. ("Universal") warrants your Universal product to be free from defects in material and workmanship for a period of five (5) years from the date of purchase. This warranty applies only to the original consumer purchaser and only to products used in normal residential use and service. If this product is found to be defective, Universal's only obligation, and your exclusive remedy, is the repair or replacement of the product, at Universal