Résumé du contenu de la page N° 1
Impact Wrench
MODEL 6953
DOUBLE
INSULATION
INSTR U CTION MANU AL
WARNING:
For your personal safety, READ and UNDERSTAND before using.
SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.
www.makitatools.com
Résumé du contenu de la page N° 2
SPECIFICATIONS Capacities No load Impacts per Max. fasten- Overall length Net weight High tensile speed (RPM) minute ing torque Standard bolt bolt 10mm - 16mm 8mm - 12mm 150 N m 233 mm 0 - 3000/min. 0 - 3000 1.4kg(3lbs) (3/8”- 5/8”) (5/16” - 1/2”) (111ft lbs) (9-1/8”) Manufacturer reserves the right to change specifications without notice. Specifications may differ from country to country. GENERAL SAFETY RULES USA002-2 (For All Tools) WARNING: Read and understand all instructions. Failur
Résumé du contenu de la page N° 3
6. Do not expose power tools to rain or wet Tool Use and Care conditions. Water entering a power tool will 15. Use clamps or other practical way to increase the risk of electric shock. secure and support the workpiece to a 7. Do not abuse the cord. Never use the cord stable platform. Holding the work by hand or to carry the tools or pull the plug from an against your body is unstable and may lead outlet. Keep cord away from heat, oil, to loss of control. sharp edges or moving parts. Replace 16.
Résumé du contenu de la page N° 4
24. When servicing a tool, use only identical Use of unauthorized parts or failure to follow replacement parts. Follow instructions in Maintenance instructions may create a risk of the Maintenance section of this manual. electric shock or injury. USE PROPER EXTENSION CORD: Make sure your extension cord is in good condition. When using an extension cord, be sure to use one heavy enough to carry the current your product will draw. An undersized cord will cause a drop in line voltage resulting in l
Résumé du contenu de la page N° 5
SAVE THESE INSTRUCTIONS WARNING: MISUSE or failure to follow the safety rules stated in this instruction manual may cause serious personal injury. SYMBOLS USD202-2 The followings show the symbols used for tool. V ....................... volts ....................no load speed n ˚ A ....................... amperes ....................Class II Construction Hz ..................... hertz .../min................revolutions or reciprocation per minute ................ alternating current ............
Résumé du contenu de la page N° 6
FUNCTIONAL CAUTION: DESCRIPTION Always be sure that the tool is switched off and unplugged before adjusting or checking function on the tool. Switch action CAUTION: Before plugging in the tool, always check to see that the switch trigger actuates properly and returns to the ''OFF'' position when released. 001642 To start the tool, simply pull the switch trigger. Tool speed is increased by increasing pressure on the switch trigger. Release the switch trigger to stop. 1 1. Switch trigger Rever
Résumé du contenu de la page N° 7
ASSEMBLY CAUTION: Always be sure that the tool is switched off and unplugged before carrying out any work on the tool. Selecting correct socket Always use the correct size socket for bolts and nuts. An incorrect size socket will result in inaccurate and inconsistent fastening torque and/or damage to the bolt or nut. Installing or removing socket CAUTION: Always be sure that the tool is switched off and unplugged before installing or removing the socket. 001644 To install the socket, push it
Résumé du contenu de la page N° 8
The proper fastening torque may differ depending upon the OPERATION kind or size of the bolt. The relation between fastening torque and fastening time is shown in the figures. OPERATION 001658 Hold the tool firmly and place the socket over the bolt or nut. Standard bolt Turn the tool on and fasten for the proper fastening time. N·m (ft·lbs) M16 (5/8”) 140 NOTE: (100) 120 When fastening screw M8 (5/16”) or smaller, carefully (86) M16 (5/8”) adjust pressure on the switch trigger so that the scre
Résumé du contenu de la page N° 9
MAINTENANCE CAUTION: Always be sure that the tool is switched off and unplugged before attempting to perform inspection or maintenance. 001145 Replacing carbon brushes Remove and check the carbon brushes regularly. Replace when they wear down to the limit mark. Keep the carbon brushes clean and free to slip in the holders. Both carbon brushes should be replaced at the same time. Use only iden- tical carbon brushes. 1 1. Limit mark 001646 Use a screwdriver to remove the brush holder caps. Take
Résumé du contenu de la page N° 10
ACCESSORIES CAUTION: These accessories or attachments are recommended for use with your Makita tool specified in this manual. The use of any other accessories or attachments might present a risk of injury to persons. Only use accessory or attachment for its stated purpose. If you need any assistance for more details regarding these accessories, ask your local Makita service center. Extension bar Universaljoint Bit adapter Phillips bits (#2, #3) 10
Résumé du contenu de la page N° 11
Memo 11
Résumé du contenu de la page N° 12
Memo 12
Résumé du contenu de la page N° 13
First-Class Postage Required Post Office will not deliver without proper postage. Makita U.S.A., Inc. 14930 Northam Street La Mirada, CA 90638-5753 Fold 13 Cut
Résumé du contenu de la page N° 14
MAIL THIS PORTION Your answer to the following questions are appreciated. 1.This product was purchased from: 3. How did you learn of about this product: Home Center Other ( ) Magazine Radio Hardware/Lumber Store From Dealer Exhibition Tool Distributor Newspaper From Friend Industrial Supply Store Display Previous Usage Construction Supply Catalog Other ( ) 2. Use of the product is intended for: 4. Most favored points are: Construction Trade Design Repair Service Industrial Maintenance Features D
Résumé du contenu de la page N° 15
FACTORY SERVICE CENTERS 1-800-4-MAKITA RETAIN THIS PORTION FOR YOUR RECORDS ALABAMA COLORADO KENTUCKY NEW MEXICO PUERTO RICO 2365 Pelham Parkway 11839 E. 51st Ave. 1215 S. Hurstbourne Parkway 5805 Menaul Blvd. NE 200 Guayama St. Pelham, AL 35124 Denver, CO 80239-2709 Louisville, KY 40222 Albuquerque, NM 87110 Hato Rey, PR 00917 (205) 620-1791 (303) 371-2850 (502) 326-3740 (505) 881-4619 (787) 250-8776 ARIZONA CONNECTICUT LOUSIANA NEW YORK TENNESSEE 3707 E. Broadway Rd., Ste. 6 508 Spring St. 562
Résumé du contenu de la page N° 16
WARNING Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are: lead from lead-based paints, crystalline silica from bricks and cement and other masonry products, and arsenic and chromium from chemically-treated lumber. Your risk from these exposures varies, depending on how often you do this type of w
