Résumé du contenu de la page N° 1
INSTALLATION INSTRUCTIONS
Instrucciones de instalación Istruzioni di installazione
Installationsanleitung Installatie-instructies
Instruções de Instalação Instructions d´installation
Medium Flat Panel In-Wall Mount
Spanish Product Description
German Product Description
Portuguese Product Description
Italian Product Description
Dutch Product Description
French Product Description
MIWRF SERIES
Résumé du contenu de la page N° 2
MIWRF SERIES Installation Instructions DISCLAIMER Milestone AV Technologies, and its affiliated corporations and CAUTION: A CAUTION alerts you to the possibility of subsidiaries (collectively, "Milestone"), intend to make this damage or destruction of equipment if you do not follow the manual accurate and complete. However, Milestone makes no corresponding instructions. claim that the information contained herein covers all details, conditions or variations, nor does it provide for every possibl
Résumé du contenu de la page N° 3
Installation Instructions MIWRF SERIES TOOLS REQUIRED FOR INSTALLATION AND PARTS 1/2" 1/8" 7/16" 9/16" 1" Universal Interface Bracket provided with Models MIWRFUB and MIWRFVB not shown. I/M B (2) x1 A (1) C (4) D (4) E (2) F (1) G (2) F1 (4) F2 (4) 5/16" x 2 1/2" 5/16" H (8) L (4) J (8) K (4) 5/16-18 Figure 1 3
Résumé du contenu de la page N° 4
MIWRF SERIES Installation Instructions Installation Cutout Area WARNING: IMPROPER INSTALLATION CAN RESULT IN DEATH OR SERIOUS PERSONAL INJURY! This accessory should be installed by qualified personnel only. WARNING: IMPROPER INSTALLATION CAN LEAD TO MOUNT FALLING CAUSING SEVERE PERSONAL INJURY OR DAMAGE TO EQUIPMENT! DO NOT deviate from installation instructions provided. DO NOT substitute hardware. The MIW Series is designed to accommodate up to 3 1/2" of lateral shift adjustment (right or left
Résumé du contenu de la page N° 5
Installation Instructions MIWRF SERIES WARNING: ELECTRICAL SHOCK HAZARD! CUTTING WARNING: IMPROPER INSTALLATION CAN LEAD TO OR DRILLING INTO ELECTRICAL WIRES OR CABLES MOUNT FALLING CAUSING SEVERE PERSONAL INJURY CAN CAUSE DEATH OR SERIOUS PERSONAL INJURY! OR DAMAGE TO EQUIPMENT! Wiring of equipment must ALWAYS make certain area behind mounting surfaces is free be performed by properly trained and certified persons of electrical wires and cables before cutting, drilling, or following all appli
Résumé du contenu de la page N° 6
MIWRF SERIES Installation Instructions Cover and Trim Installation Cover Installation To install covers: (F1) x4 (F2) x4 1. Install upper and lower wall channel covers (E) by tipping cover top down and positioning as shown in end view of figure below. (See Figure 8) 2. Tap firmly across bottom of channels to lock in place as shown in figure below. (See Figure 8) 3. Install four R.H. and L.H. end caps (D) by aligning tabs on 9 (A) x1 end caps (F) with slots in wall channel covers (E) and sliding
Résumé du contenu de la page N° 7
Installation Instructions MIWRF SERIES To install display: Trim Installation To install optional trim; 1. Install interface bracket (if model MIWRFUB or MIWRFVB) following the installation instructions provided with the 1. Orient two trim pieces (G) as shown in figure below. interface bracket. (See Figure 9) 2. Move mount faceplate to extended position by grasping 2. Slide slat in trim edge over lip in mount enclosure and press faceplate and pulling outward away from wall. trim (G) onto enclosur
Résumé du contenu de la page N° 8
MIWRF SERIES Installation Instructions CABLE MANAGEMENT ADJUSTMENTS Pitch Tension Adjustment WARNING: IMPROPER INSTALLATION CAN LEAD TO To adjust display pitch tension: SERIOUS PERSONAL INJURY OR DAMAGE TO 1. With display installed, tighten or loosen two screws, one on EQUIPMENT! Make sure cables do not run through pinch each side. (See Figure 14) points. 2. Check for desired tension. 3. Repeat Steps 1 and 2 until desired tension is obtained. 1. Locate and install cable tie clips (J) where desi
Résumé du contenu de la page N° 9
Installation Instructions MIWRF SERIES 2 1 1 (on back side in this view) 3 2 Figure 16 Display Height Adjustment The mount is designed to accommodate up to 1" of display height adjustment. To adjust display height: 1. With display installed, loosen adjustment locking screw using hex wrench. (See Figure 17) 2. Adjust display height by turning adjustment nut in desired Figure 15 direction. (See Figure 17) Extend/Retract Tension Adjustment 3. Tighten adjustment locking screw when display is at des
Résumé du contenu de la page N° 10
MIWRF SERIES Installation Instructions YAW Tension Adjustment The mount is designed to accommodate up to 37.5 deg. of travel to left and right of center. To adjust YAW tension: 1. With display installed, loosen adjustment screw using hex wrench. (See Figure 18) 2. Check for desired tension. 3. Repeat Steps 1 and 2 until desired tension is obtained. NOTE: If changing from a smaller display to a larger display may be necessary to increase tension. 1 3 TOP VIEW Figure 18 10
Résumé du contenu de la page N° 11
Installation Instructions MIWRF SERIES DIMENSIONS 11
Résumé du contenu de la page N° 12
MIWRF SERIES Installation Instructions USA/International A 8401 Eagle Creek Parkway, Savage, MN 55378 P 800.582.6480 / 952.894.6280 F 877.894.6918 / 952.894.6918 Europe A Fellenoord 130 5611 ZB EINDHOVEN, The Netherlands Chief Manufacturing, a products division P +31 (0)40 2668620 of Milestone AV Technologies F +31 (0)40 2668615 Asia Pacific A Room 24F, Block D, Lily YinDu International Building LuoGang, BuJi Town, Shenzhen, CHINA. 8805-000249 Rev A 2008 Milestone AV Technologies P +86-755-8996
