Résumé du contenu de la page N° 1
INSTALLATION INSTRUCTIONS
Instrucciones de instalación Istruzioni di installazione
Installationsanleitung Installatie-instructies
Instruções de Instalação Instructions d´installation
XSM
XTM
FUSION EXTRA LARGE HEIGHT ADJUST
FLAT PANEL MOUNTS
XSM/XTM Series
Résumé du contenu de la page N° 2
XSM/XTM Series Installation Instructions DISCLAIMER Milestone AV Technologies, and its affiliated corporations and CAUTION: A CAUTION alerts you to the possibility of subsidiaries (collectively "Milestone"), intend to make this damage or destruction of equipment if you do not follow the manual accurate and complete. However, Milestone makes no corresponding instructions. claim that the information contained herein covers all details, conditions or variations, nor does it provide for every possib
Résumé du contenu de la page N° 3
Installation Instructions XSM/XTM Series DIMENSIONS XSM MAX MOUNTING PATTERN IS 46" (1168.4 mm) WITHOUT REVERSING UPRIGHTS WITH REVERSING THE UPRIGHTS MAX MOUNTING PATTERN IS 48.4" (1229.4 mm) 0 10.2 45 .40 12.9 1.77 .51 90 3.54 105 4.13 24.3 MINIMUM UPRIGHT SPACING 38.4 150 .96 24" 25.4 5.91 1.51 73.9 1.00 165 2.91 6.50 210 8.27 225 8.3 8.86 270 .33 10.63 285 51 11.22 2 383.4 44.5 685.8 330 15.10 1.75 27.00 419.6 12.99 16.52 345 13.58 405 RAILS CAN BE SLID LEFT 15.94 OR RIGHT FOR OFFSET 25.4 46
Résumé du contenu de la page N° 4
XSM/XTM Series Installation Instructions LEGEND Tighten Fastener Pencil Mark Apretar elemento de fijación Marcar con lápiz Befestigungsteil festziehen Stiftmarkierung Apertar fixador Marcar com lápis Serrare il fissaggio Segno a matita Bevestiging vastdraaien Potloodmerkteken Serrez les fixations Marquage au crayon Loosen Fastener Drill Hole Aflojar elemento de fijación Perforar Befestigungsteil lösen Bohrloch Desapertar fixador Fazer furo Allentare il fissaggio Praticare un foro Bevestiging los
Résumé du contenu de la page N° 5
Installation Instructions XSM/XTM Series TOOLS REQUIRED FOR INSTALLATION #2 7/32" (5.5mm) Wood Stud 5/16" (7.9mm) Concrete PARTS B (1) C (1) A (1) [Included with XSM2XXX/XTM2XXX (XTM Only) Models Only] J (1) [Used on XSMU/XTMU Models Only] E (1) Custom J2 (6) J1 (6) XSM2XXX/ M6x25mm M6x16mm XTM2XXX Hardware G (1) F (1) J3 (6) J4 (6) M8x20mm M8x30mm (XSM Only) J5 (4) J6 (6) M8x50mm M10x40mm H (4) K (1) J7 (6) J8 (6) J9 (6) M10x50mm M6 M8 L (1) K1
Résumé du contenu de la page N° 6
XSM/XTM Series Installation Instructions INSTALLATION Center of screen The XTM and XSM have been designed to be mounted directly onto either a wood stud or concrete wall. The XTM has brackets which allow the display to be tilted. The XSM has static brackets which keep the display in an upright position. 7-1/2" Locate Mounting Site WARNING: IMPROPER INSTALLATION CAN LEAD TO MOUNT FALLING CAUSING SEVERE PERSONAL INJURY OR DAMAGE TO EQUIPMENT! It is the installers responsibility to make certain the
Résumé du contenu de la page N° 7
Installation Instructions XSM/XTM Series WARNING: EXPLOSION AND FIRE HAZARD! CUTTING OR DRILLING INTO GAS PLUMBING CAN CAUSE DEATH OR SERIOUS PERSONAL INJURY! ALWAYS make certain 5 6 area behind mounting surface is free of gas, water, waste, or any other plumbing before cutting, drilling, or installing fasteners. 8 4 (K1) x 4 6 10 x4 5 9 7 (K3) x 4 10 8 9 (K2) x 4 Figure 2 8. Mark the attachment points for the lower mounting slots, 7 11 (K3) x 4 making sure the attachment points are located on t
Résumé du contenu de la page N° 8
XSM/XTM Series Installation Instructions 1 Knobs Center of bracket Figure 4 WARNING: IMPROPER INSTALLATION CAN LEAD TO 2 DISPLAY FALLING CAUSING SERIOUS PERSONAL INJURY OR DAMAGE TO EQUIPMENT! Using screws of improper size may damage your display. Properly sized screws will easily and completely thread into display mounting holes. If spacers are required, be sure to use longer screws of the same diameter. Figure 5 2. Select correct screws, spacers (if necessary) and washers from the hardware bag
Résumé du contenu de la page N° 9
Installation Instructions XSM/XTM Series Center Line (CL) 3d 3e Pull strap NEVER place both interface brackets to one side of the wall mount center line (CL)! Knobs to outside of brackets Figure 6 Attaching Screen to Wall Mount 1. Attach wall bracket caps (H) to top and bottom of both wall brackets. (See Figure 7) Both interface brackets must NEVER be located to one side of the wall brackets! Figure 8 XTM Model NOTE: Proceed to Step 8 for XSM Model instructions. 3. Hang top hook of interfac
Résumé du contenu de la page N° 10
XSM/XTM Series Installation Instructions 7. Proceed to Adjusting Roll/Height of Wall Brackets 10. Move screen towards the wall by pulling display bottom section. away from wall and pushing the interface bracket tabs up one notch to the detent which you will be able to feel (approximately half way up). 11. Push bottom of display toward the wall bracket so that lower (Screen not shown for clarity) latch on interface bracket surrounds lower bar of wall mount. Top 12. Raise interface brackets tabs a
Résumé du contenu de la page N° 11
Installation Instructions XSM/XTM Series Locking XSM Mount (Optional) Add padlock (not included) to interface bracket tab to lock the XSM mount. (See Figure 13) Add padlock Figure 13 11
Résumé du contenu de la page N° 12
XSM/XTM Series Installation Instructions USA/International A 8401 Eagle Creek Parkway, Savage, MN 55378 P 800.582.6480 / 952.894.6280 F 877.894.6918 / 952.894.6918 Europe A Fellenoord 130 5611 ZB EINDHOVEN, The Netherlands P +31 (0)40 2668620 F +31 (0)40 2668615 Chief Manufacturing, a products Asia Pacific A Room 24F, Block D, Lily YinDu International Building division of Milestone AV Technologies LuoGang, BuJi Town, Shenzhen, CHINA. 8805-000259 P +86-755-8996 9226 2008 Milestone AV Technologies
