Instruction d'utilisation Fisher-Price L0538

Résumé du contenu de la page N° 1

L0538
www.fisher-price.com/uk
WARNING
IMPORTANT! KEEP INSTRUCTIONS
FOR FUTURE REFERENCE.

Résumé du contenu de la page N° 2

Consumer Information WARNING � Please read these instructions before assembly and use of this product. To prevent serious injury or death: � Adult assembly is required. Tool needed for assembly: Phillips screwdriver (not included). � Fall Hazard - It is dangerous to use � Requires one "D" (LR20) alkaline battery (not included) for this reclined cradle on an elevated soothing unit operation. Includes two LR44 button batteries for surface, since child's movement may flower toy operation. cau

Résumé du contenu de la page N° 3

Parts IMPORTANT! Please remove all parts from the package and identify them before assembly. Some parts may be packed in the pad. 2 Toys (Toys may be different) Adjustable Pillow Seat Back Tube Pad Footrest Left Base Wire Base Tube 2 Feet Right Base Wire 3 #8 x 1,9 cm ( /4") Screw – 2 M5 x 20 mm Screw – 2 Shown Actual Size NOTE: Tighten and loosen all screws with a Phillips screwdriver. Do not over-tighten the screws. 3

Résumé du contenu de la page N° 4

Assembly IMPORTANT! Before assembly and each use, inspect this product for damaged hardware, loose joints, missing parts or sharp edges. DO NOT use if any parts are missing or broken. Contact Mattel for replacement parts and instructions if needed. Never substitute parts. Base Tube Left Base Wire Right Base Wire 1 3 � Place the base tube on a flat surface. � Position the left and right base wires as shown. � Fit the left base wire and right base wire into the base tube. � Insert an M5 x 20

Résumé du contenu de la page N° 5

Assembly Seat Back Tube Seat Back Pocket Square Openings Bottom Pocket 5 � Position the seat back tube so that the square openings are upright. � Fit the seat back tube onto the ends of the base wire. 7 � Push the seat back tube to be sure it is completely on the base wires. � Fit the pad seat back pocket over the seat back tube. � Pull and fit the pad seat bottom pocket around the soothing unit and footrest. Handles 8 6 � Fit the handles through the side openings in the pad. 3 � Insert a #8

Résumé du contenu de la page N° 6

Assembly Battery Installation Hint: We recommend using an alkaline battery for longer battery life. Toy Bar Plugs 1,5V – “D” (LR20) + Sockets � Protect the environment by not disposing of this product with household waste (2002/96/EC). Check your local authority for recycling advice and facilities (Europe only). 9 � Insert and “snap” the toy bar plugs into each handle socket. Hint: The toy bar is removable. Press the ends of the latches and lift the toy bar. Toy Bar Straps 1 � Remove the pa

Résumé du contenu de la page N° 7

Battery Safety Information Setup and Use In exceptional circumstances, batteries may leak fluids that can cause a chemical burn injury or ruin your Restraint Pad product. To avoid battery leakage: � Do not mix old and new batteries or batteries of different types: alkaline, standard (carbon-zinc) or rechargeable (nickel-cadmium). � Insert batteries as indicated inside the battery compartment. � Remove batteries during long periods of non-use. Always remove exhausted batteries from the produc

Résumé du contenu de la page N° 8

Adjustable Pillow Soothing Unit and Toybar Pillow Strap P Power Switch Power Switch ower Switch � Make sure your child is properly secured in the seat. Soothing Unit � Slide the power switch to: Vibrations or Off. IMPORTANT! Low battery power causes this product to operate erratically: no vibrations and the product may not turn off. Remove and discard the battery and replace with a new 1 “D” (LR20) alkaline battery. Toy Bar � Pull the ring on the centre toy for a delightful tune! � Place t