Instruction d'utilisation Hans Grohe 35807801

Résumé du contenu de la page N° 1

Installation Instructions / Warranty
Axor Steel
35807801

Résumé du contenu de la page N° 2

Axor Steel Kitchen Faucet 35807801 Max water pressure 145 PSI Recommended water pressure 45 - 7.5 PSI o o Recommended hot water temp 10 - 140 F* Hole size in mounting surface 1 1/” Max. mounting surface thickness 1/4”  Flow rate: . GPM  *Please know and follow all applicable local codes when setting the temperature on the water heater. o In Massachusetts, the water heater may be set no higher than 11 F. Installer Notes: Significant pressure differences between t

Résumé du contenu de la page N° 3

Preparation for Installation: Turn the water supplies off before removing the old faucet. Flush the supply lines of debris before beginning installation. Damage to the cartridge caused by debris is not covered under the Hansgrohe limited lifetime warranty. Install the faucet: Position the faucet and sealing ring on top of the mounting surface. From beneath, install the plastic washer, slide washer and metal washer. Thread on the collar nut loosely. If the total thickness of the mounting

Résumé du contenu de la page N° 4

Connect the handspray hose: Loosen the compression fitting on the end of the flexible handspray hose. Slide it onto the end of the handspray supply hose. While holding the hose still with a 1 mm wrench, tighten the nut with a 17 mm wrench. Do noT aLLoW THe HoSe To TWIST . IF THe HoSe TWISTS, THe FLoW FRoM THe SPRayHeaD May Be ReDuceD. Connect the supplies: connect the hot and cold supply hoses to the supplies with 3/8” compression fittings (not included). Tighten them wrench tight.

Résumé du contenu de la page N° 5

Set the High Temperature Limit Stop (optional): Turn off the water at the supply stops. close the drain or cover it with a cloth. Gently pry off the screw cover. Put it aside in a safe place. use a 4mm hex wrench to loosen the handle screw (4 revolutions). Remove the handle and the decorative flange underneath. Remove the nut. Remove the handle screw from the stem of the cartridge. Remove the high temperature limit stop. Replace the high temperature limit stop so that the pin is

Résumé du contenu de la page N° 6

Replacement Parts: 1. handle 35891800 1.1 screw cover 9418000 1   flange 9750800 1.1 3 nut 94194000 3 4 M3 cartridge 9730000 4 5 hose 95048000  handspray 35893800 7 aerator 9791000 10 8 mounting set 95049000 9 check valve 97350000 filter  10 connection hose 9510000 11 hose weight 98551000 1 1 squeezing connection 9099000 9 7 5 8 11 

Résumé du contenu de la page N° 7

Cleaning Recommendation for Hansgrohe Products Modern lavatory faucets, kitchen faucets and showers consist of very different materials to comply with the needs of the market with regard to design and functionality. To avoid damage and returns, it is necessary to consider certain criteria when cleaning. Cleaning Materials for Faucets and Showers acids are a necessary ingredient of cleaning materials for removing lime, however please pay attention to the follow- ing points when cleaning faucet

Résumé du contenu de la page N° 8

THIS WaRRanTy DoeS noT coVeR and HanSGRoHe WILL noT P ay FoR: a. conditions, malfunctions or damage not resulting from defects in material or workmanship. B. conditions, malfunctions or damage resulting from (1) normal wear and tear, improper installation, improper maintenance, misuse, abuse, negligence, accident or alteration, or () the use of abrasive or caustic cleaning agents or “no-rinse” cleaning products, or the use of the product in any manner contrary to the product instructions. (3)