Résumé du contenu de la page N° 1
ENGLISH ESpañOL
See page 2 Vea la página 37
Model 45051 Hunter Home Light Control System
Installation and Operation Manual
43012-01 r101107
Résumé du contenu de la page N° 2
TABLE OF CONTENTS Introduction..............................2 Vacation program.....................25 Features...................................3 Manual Operation.....................30 Limitations/Warnings..............4 Keychain Remote Operation....31 Transmitter Controls...............5 Daily Operation.........................32 Transmitter Wall Mount.............34 Receiver Controls....................7 Setup.........................................8 Maintenance.............................
Résumé du contenu de la page N° 3
Features • A Home Program with three modes: ~ 7-day Same mode - allows you to quickly and easily program the same On/Off times for every day of the week either for all Light Groups or for individual Light Groups. ~ Week / Weekend mode - allows you to program the same On/Off times for the weekdays, and different On/Off times for the weekend either for all Light Groups or for individual Light Groups. ~ Custom mode - allows you to program individual On/Off times for each day of
Résumé du contenu de la page N° 4
Limitations & Warnings • For use with switched wall outlets. • Maximum load for receptacles is 500 watts. • Receivers conform to UL 60730-2-7, Timers and Time Switches. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply w
Résumé du contenu de la page N° 5
Transmitter Controls WIRELESS LA MP TIMER SY STEM all Off / Scroll Up/ all Off / Scroll Setup Left Button Button ALL SETUP OFF OFF A D B C ALL ALL ON ON ON all On / Scroll all On / Right / Enter Scroll Down Button Button Transmitter Controls 43012-01 5
Résumé du contenu de la page N° 6
Transmitter Controls (cont.) 1 2 3 Channel Switch •VA C ATION •HOME •M ANU AL program Select Switch 43012-01 6
Résumé du contenu de la page N° 7
Receiver Controls Light Group Select Dial Channel Select Dial Receiver Controls 43012-01 7
Résumé du contenu de la page N° 8
Setup 1) Remove the Battery Cover from the back of the Transmitter. 2) Slide the Channel Select Switch to any of the three numbers next to it. 1 2 3 43012-01 8
Résumé du contenu de la page N° 9
Setup (cont.) 3) On each Receiver rotate the Channel Select Dial to the channel to which you set the Transmitter Channel Select Switch. Channel Select Dial (shown with channel 3 selected) 4) The Hunter Home Light Control System divides the rooms and areas of your home into four Light Groups labeled a, B, C, and D on the Transmitter keyboard. assign your rooms and areas to Light Groups, and make a note of the assignments. We suggest that the entry area of your home be as- signed to Light G
Résumé du contenu de la page N° 10
Setup (cont.) NOTE - OBTAINING ADDITIONAL RECEIVERS Each Light Group can support an unlimited number of Receivers. To purchase additional Receivers, visit our website at www.hunterfan.com. 5) On each Receiver rotate the Light Group Select Dial to the Light Group for which it is intended. Light Group Select Dial (shown with Light Group C selected) 43012-01 10
Résumé du contenu de la page N° 11
Setup (cont.) 6) Plug your lamps into the Receivers (observing correct plug polarities), then plug the Receivers into standard wall electrical outlets. Receiver plugs into wall outlet. Lamp plugs in under Receiver 7) Switch the lamps that will be controlled by the Home Light Control System to the On position. 43012-01 11
Résumé du contenu de la page N° 12
Setup (cont.) 8) Install two fresh AA batteries into the Battery Compartment. Ensure the battery polarities are correctly oriented. 9) Reinstall the Battery Cover. 10) The Welcome screen will appear: WELCOME PRESS ANY KEY TO BEGIN SETUP 11) Press any key. The Setup screen will appear: SETUP DATE / TIME ENTER 12) To exit Setup press or so the Setup screen shows Exit, then press . To proceed with Setup press . If you decide to exit the Setup, then the Setup Complete scr
Résumé du contenu de la page N° 13
Setup (cont.) After approximately five seconds the screen will show the mode on which the Program Select Switch is set. If you decide to proceed with Setup, then the Calendar / Clock screen will appear: JAN 01 2007 12:00A MONDAY ENTER NOTE - BUTTON OPERATION Press or to select the Calendar and Clock positions; press or to change settings. To fast scroll, press and hold the buttons; for slow scroll, press the buttons repeatedly. 13) Press or to find the
Résumé du contenu de la page N° 14
Setup (cont.) 17) Press or to find the current minute. Press to set the minute. The Automatic Daylight Savings Time screen will appear. AUTO DST UPDATE? YES ENTER NOTE - AUTOMATIC DAYLIGHT SAVINGS TIME SETTING If you select Yes, then the Home Light Control will update automatically for Daylight Savings Time. 18) Press or to choose Yes or No. Press to set your choice. The Final Setup screen will appear: SETUP PROGRAM ENTER 19) To proceed to the
Résumé du contenu de la page N° 15
Home Program The Home Program has three modes: PROGRAM: HOME 7 DAY SAME ENTER ~ 7-day Same mode - allows you to quickly and easily program the same On/Off times for every day of the week either for all Light Groups or for individual Light Groups. PROGRAM: HOME WEEK / WEEKEND ENTER ~ Week / Weekend mode - allows you to program the same On/Off times for the weekdays, and different On/Off times for the weekend either for all Light Groups or for individual Light Groups. PROG
Résumé du contenu de la page N° 16
Home Program (cont.) To program the 7-day Same mode: PROGRAM: HOME 7 DAY SAME ENTER 1) Press to select the 7 Day Same mode. The Time/Group screen will appear: ON 06:00A 05:00P OFF 08:00A 11:00P GROUP A ENTER NOTE - PROGRAMMING TIMES You can program two different On/Off times for each Light Group. NOTE - GROUPS The word GROUP on the screen means Light Group. 2) Press or to select the Time and Group positions. Press or to change the settings. To fast
Résumé du contenu de la page N° 17
Home Program (cont.) 3) Once your desired times are programmed the screen will show: SAME PROGRAM FOR ALL GROUPS? YES ENTER 4) Press to program the other Light Groups with the same times for every day of the week. The screen will show the Vacation Program screen (explained later). If you want to program the other Light Groups with different times for everyday of the week, or if you want to program no other Light Groups, then press or so the screen shows “NO”: S
Résumé du contenu de la page N° 18
Home Program (cont.) 6) Press to program the other individual Light Groups with different times for every day of the week. You will be taken back to Step 2 of the 7-Day Same option. If you do not want to program the other Light Groups with different times, then press or so the screen shows “NO”: PROGRAM ADDITIONAL GROUPS? NO ENTER 7) Press . The screen will show the Vacation Program option screen (explained on page 26): PROGRAM VACATION NOW? YES
Résumé du contenu de la page N° 19
Home Program (cont.) To program the Week / Weekend mode: PROGRAM: HOME WEEK / WEEKEND ENTER 1) Press to select the Week / Weekend option option. The Week Time/Group screen will appear: ON 06:00A 05:00P WEEK OFF 08:00A 11:00P GROUP A ENTER 2) Press or to select the Time and Group positions. Press or to change the settings. To fast scroll, press and hold the buttons; for slow scroll, press the buttons repeatedly. When your desired setting appears, pres
Résumé du contenu de la page N° 20
Home Program (cont.) 3) Press or to select the Time and Group positions. Press or to change the settings. To fast scroll, press and hold the buttons; for slow scroll, press the buttons repeatedly. When your desired setting appears, press . The Weekend Time/Group for Sunday screen will appear: ON 06:00A 05:00P SUN OFF 08:00A 11:00P GROUP A ENTER 5) Press or to select the Time and Group positions. Press or to change the settings. To
