Instruction d'utilisation Peerless Industries Peerless SmartMount Universal Tilt Wall Mount ST630

Résumé du contenu de la page N° 1

Installation and Assembly:
SmartMount™ Universal Tilt Wall Mount
for 10" - 24" LCD Flat Panel Screens
Models: ST 630P, ST 630P-S, ST 630, ST 630-S
This product is intended for use with UL
Features: Listed products and must be installed by a

qualified professional installer.
• Fits 10" to 24" LCD flat panel screens
• One-touch tilt for effortless positioning and adjustment of the screen Max UL Load Capacity: 80 lb (36.3 kg)
3215 W. North Ave. • Melrose Park, IL 60160 • (800) 865-2112 or (70

Résumé du contenu de la page N° 2

Note: Read entire instruction sheet before you start installation and assembly. WARNING • Do not begin to install your Peerless product until you have read and understood the instructions and warnings contained in this Installation Sheet. If you have any questions regarding any of the instructions or warnings, please call Peerless customer care at 1-800-865-2112. • This product should only be installed by a qualified professional. • Make sure that the wall will safely support the combined load o

Résumé du contenu de la page N° 3

Parts List ST 630P ST 630P-S ST 630 ST 630-S Description Qty Part # Part # Part # Part # A adapter plate 1 095-1346 095-4346 095-1346 095-4346 B tilt assembly 1 095-0359 095-0360 095-0359 095-0360 Alligator® anchor 2 590-0097 590-0097 590-0097 590-0097 C D M4 x 10 mm phillips screw 4 504-9012 504-9012 504-9012 504-9012 E M4 x 20 mm phillips screw 4 504-9020 504-9020 504-9020 504-9020 F retaining spacer 4 590-5005 590-5005 590-5005 590-5005 G #14 x 2-1/2" hex head wood screw 2 5S1-015-C03 5S1-015

Résumé du contenu de la page N° 4

Installation to Single Wood Stud Wall WARNING • Make sure that the wall will safely support the combined load of the equipment and all attached hardware and components. Use a stud finder to locate the edges of the stud. Use of an edge-to-edge stud finder is highly recommended. Based 1 on its edges, draw a vertical line down the stud’s center. Place tilt assembly (B) on wall as a template, making sure that the two mounting holes are over the stud centerline. Level tilt assembly, and mark the cent

Résumé du contenu de la page N° 5

SOLID CINDER BLOCK CONCRETE Installation to Solid Concrete or Cinder Block WARNING • When installing Peerless wall mounts on cinder block, verify that you have a minimum of 1-3/8" of actual concrete thickness in the hole to be used for the concrete anchors. Do not drill into mortar joints! Be sure to mount in a solid part of the block, generally 1" minimum from the side of the block. Cinder block must meet ASTM C-90 specifica- tions. It is suggested that a standard electric drill on slow setting

Résumé du contenu de la page N° 6

Attaching Adapter Plate to Flat Panel Screen WARNING • If screws don't get three complete turns in the screen inserts or if screws bottom out and bracket is still not tightly secured, damage may occur to screen or product may fail. ® FOR VESA 75 MOUNTING PATTERN: FOR VESA 100 MOUNTING PATTERN: 2 Choose hole pattern as shown below. Attach adapter Choose hole pattern as shown below. Attach adapter plate (A) to back of screen using four M4 x 10 mm plate (A) to back of screen using four M4 x 10 mm s

Résumé du contenu de la page N° 7

Installing and Removing Flat Panel Screen Attach screen to tilt assembly (B). Tighten M5 x 6 3 mm screw (H) to lock screen to tilt assembly. SCREEN Note: For security models, use security driver (I) to H tighten M5 x 6 mm screws (H). To remove screen from mount, loosen screw (H) and lift screen off of mount. A WARNING • Do not lift more weight than you can handle. Use additional man power or mechanical lifting equipment to safely handle placement of the screen. • Failure to lock adapter plate (A