Résumé du contenu de la page N° 1
XG200 Elliptical
OWNER’S MANUAL
Please carefully read this entire manual before operating your new elliptical
Résumé du contenu de la page N° 2
TABLE OF CONTENTS Product Registration 1 Important Safety Instructions 2 Important Electrical Instructions 3 Important Operation Instructions 4 Features 4 XG200 Assembly Instructions 5 Console Operation 11 General Maintenance 13 Manufacturer’s Limited Warranty 14 ATTENTION This elliptical is intended for residential use only and is warranted for this application. Any other application voids this warranty in its entirety.
Résumé du contenu de la page N° 3
Congratulations on your new elliptical and welcome to the Spirit family! Thank you for your purchase of this quality elliptical trainer from Spirit Manufacturing, Inc. Your new elliptical was manufactured by one of the leading fitness manufacturers in the world and is backed by one of the most comprehensive warranties available. Through your dealer, Spirit will do all we can to make your ownership experience as pleasant as possible for many years to come. If not purchased direct from Spirit,
Résumé du contenu de la page N° 4
IMPORTANT SAFETY INSTRUCTIONS WARNING - Read all instructions before using this appliance. If using the optional power supply: DANGER - To reduce the risk of electric shock disconnect your Spirit elliptical from the electrical outlet prior to cleaning and/or service work. WARNING - To reduce the risk of burns, fire, electric shock, or injury to persons, install the elliptical on a flat level surface with access to a 110-volt, 15-amp grounded outlet with only the elliptical plugged into the cir
Résumé du contenu de la page N° 5
IMPORTANT ELECTRICAL INSTRUCTIONS WARNING! NEVER remove any cover without first disconnecting AC power. If voltage varies by ten percent (10%) or more, the performance of your elliptical may be affected. Such conditions are not covered under your warranty. If you suspect the voltage is low, contact your local power company or a licensed electrician for proper testing. NEVER expose this elliptical to rain or moisture. This product is NOT designed for use outdoors, near a pool or spa, or in a
Résumé du contenu de la page N° 6
IMPORTANT OPERATION INSTRUCTIONS NEVER operate this elliptical without reading and completely understanding the results of any operational change you request from the computer. Understand that changes in resistance do not occur immediately. Set your desired resistance level on the computer console and release the adjustment key. The computer will obey the command gradually. NEVER use your elliptical during an electrical storm. Surges may occur in your household power supply that coul
Résumé du contenu de la page N° 7
XG200 ASSEMBLY INSTRUCTIONS PRE-ASSEMBLY 1. Using a razor knife (Box Cutter), cut the banding straps that wrap around the carton. Reach under the bottom edge of the carton and pull it away from the cardboard underneath, separating the staples that join the two together. Lift the box over the unit and unpack. 2. Carefully remove all parts from carton and inspect for any damage or missing parts. If damaged parts are found, or parts are missing, contact your dealer immediately. 3. Locate the h
Résumé du contenu de la page N° 8
CONSOLE MAST 1. The computer cable is pre-installed to the console mast and main frame so be careful not to pull too hard on the console mast during assembly to avoid 1 damaging them. 2. Connect cable (100) to (101). 3. Place the console mast onto the mating plate of the main frame; Be careful not to pinch the speed sensor wire between the console mast and the main frame plates during assembly. 4. Secure the console mast in place with the four stainless steel bolts (42) and split washers (5
Résumé du contenu de la page N° 9
SWING ARMS & PEDALS 1. Remove the foam from the console mast axles and the plastic ties from the tubes that slide onto 2 the console mast axles. 2. Slide the two swing arms (8 Right & 9 Left) onto the console mast axle. There is a left and right swing arm (marked with an “R” and an “L”) so make sure you assemble the correct one on each side. Do not force the arms onto the axle or use a hammer, as damage to the bearings could occur. The swing arms have been previously installed at the factory
Résumé du contenu de la page N° 10
CONSOLE 1. Attach the transport wheels (77) to each bracket with the two bolts (44) and nuts (34). Partially 3 tighten with the wrenches provided (110 & 111). Over tightening the hardware won’t allow the wheels to rotate. 2. Remove the cover on the back of the console and install the 4 C batteries. 3. Snap the four end caps (67) onto the cup washers on the left & right pedal arm assemblies. HARDWARE #44. 5/16” x 1-3/4” #34. 5/16” Bolt Nut (2 pcs) (2 pcs) XG200 Elliptical 8
Résumé du contenu de la page N° 11
ARM ATTACHMENTS 1. Assemble the brackets at the bottom of the swing arms to the pedal arms using a shoulder bolt (55) and a nut (56) on each side. Tighten securely with the wrenches provided (109 & 116). 4 HARDWARE #55. M10 x 20mm #56. M10 Shoulder Bolt Nut (2 pcs) (2 pcs) 9 XG200 Elliptical
Résumé du contenu de la page N° 12
LEVELERS & END CAPS 1. Tilt the elliptical to one side and put something under the unit for support and install the three levelers (83) for that side. Tilt the unit to the other side and install those three levelers (83). Level 5 the elliptical once it is positioned where it will be used. Screw the two middle levelers all the way in and the front and rear levelers all the way in, then back them out about two or three turns. Level the unit using only the front and rear levelers first, then ad
Résumé du contenu de la page N° 13
CONSOLE OPERATION POWER The power for the console is provided by 4 C alkaline batteries (provided) and will operate on rechargeable NiCd C batteries. There is an AC electrical power supply that will override the batteries when used. The power supply will not charge the batteries. The NiCD batteries will need to be charged separately. Once the batteries are installed or the electrical cord is plugged into an outlet, the console will power on, the Time window will display an hour meter readi
Résumé du contenu de la page N° 14
DISPLAYS TIME: Displays workout time two ways; either count up (accumulated time) or count down (remaining time), depending on your preference. RPM/SPEED: Displays the current pedaling speed as revolutions per minute or miles per hour. LEVEL/DISTANCE: Displays resistance Level or virtual distance traveled in miles or kilometers (units selected through management mode, see page 13 for details). CALORIES/PULSE: Displays total calories burned during the current exercise session or heart rate i
Résumé du contenu de la page N° 15
GENERAL MAINTENANCE The elliptical is practically maintenance free. Just keep it clean by wiping down the unit with a damp cloth after each use. Do not use harsh detergents. Every month check that all the hardware is securely tightened. Do not use the elliptical if any parts are loose or broken. The wheels and aluminum tracks will need to be kept clean to prevent noise and maintain smoothness. No lubrication should be necessary but if persistent noises from the wheels develop you can use
Résumé du contenu de la page N° 16
MANUFACTURER’S LIMITED WARRANTY ELLIPTICAL WARRANTY - Effective September 15, 2010 Spirit Fitness Inc. warrants all its elliptical parts for a period of time listed below from the date of retail sale, as determined by sale receipt, or in the absence of a sales receipt eighteen (18) months from the original factory shipping date. Spirit’s responsibilities include providing new or remanufactured parts, at Spirit’s option, and technical support to our independent dealers and servicing organizat
