Résumé du contenu de la page N° 1
Dell OptiPlex 9010 All-In-One (Touch)
Owner's Manual
Regulatory Model: W04C
Regulatory Type: W04C001
Résumé du contenu de la page N° 2
Notes, Cautions, and Warnings NOTE: A NOTE indicates important information that helps you make better use of your computer. CAUTION: A CAUTION indicates either potential damage to hardware or loss of data and tells you how to avoid the problem. WARNING: A WARNING indicates a potential for property damage, personal injury, or death. © 2013 Dell Inc. All Rights Reserved. ™ ™ ™ ™ ™ ™ ™ Trademarks used in this text: Dell , the Dell logo, Dell Boomi , Dell Precision , OptiPlex , Latitude , PowerEdge
Résumé du contenu de la page N° 3
Contents 1 Working on Your Computer....................................................................................................... 7 Before Working Inside Your Computer.....................................................................................................................7 Turning Off Your Computer....................................................................................................................................... 8 After Working Inside Your Computer........
Résumé du contenu de la page N° 4
Removing the Input/Output Board Shield............................................................................................................... 27 Installing the Input/Output Board Shield................................................................................................................ 29 Removing the Power-Button Board........................................................................................................................29 Installing the Power-Button Board....
Résumé du contenu de la page N° 5
6 Technical Specifications......................................................................................................... 73 7 Contacting Dell ......................................................................................................................... 79
Résumé du contenu de la page N° 6
6
Résumé du contenu de la page N° 7
1 Working on Your Computer Before Working Inside Your Computer Use the following safety guidelines to help protect your computer from potential damage and to help to ensure your personal safety. Unless otherwise noted, each procedure included in this document assumes that the following conditions exist: • You have read the safety information that shipped with your computer. • A component can be replaced or--if purchased separately--installed by performing the removal procedure in reverse orde
Résumé du contenu de la page N° 8
CAUTION: Before touching anything inside your computer, ground yourself by touching an unpainted metal surface, such as the metal at the back of the computer. While you work, periodically touch an unpainted metal surface to dissipate static electricity, which could harm internal components. Turning Off Your Computer CAUTION: To avoid losing data, save and close all open files and exit all open programs before you turn off your computer. 1. Shut down the operating system: – In Windows 8: * Usi
Résumé du contenu de la page N° 9
Important Information NOTE: Avoid using the touchscreen in dusty, hot, or humid environments. NOTE: Sudden change in temperature may cause condensation on the inner surface of the glass screen, which will disappear after a short time and does not affect normal usage. 9
Résumé du contenu de la page N° 10
10
Résumé du contenu de la page N° 11
2 Removing and Installing Components This section provides detailed information on how to remove or install the components from your computer. Recommended Tools The procedures in this document may require the following tools: • Small flat-blade screwdriver • Phillips screwdriver • Small plastic scribe Removing the Video Electronics Standards Association (VESA) Stand 1. Follow the procedures in Before Working Inside Your Computer. 2. Place the computer on a flat surface, display side facing down
Résumé du contenu de la page N° 12
5. Remove the screws that secure the VESA stand to the computer and lift the VESA stand away from the computer. Installing the VESA Stand 1. Align and place the VESA stand on the back of the computer. 2. Tighten the screws to secure the VESA stand to the computer. 3. Place and press the VESA cover on the computer, till it clicks into place. 4. Follow the procedures in After Working Inside Your Computer. Removing the Back Cover 1. Follow the procedures in Before Working Inside Your Computer. 2. R
Résumé du contenu de la page N° 13
4. Lift the cover and remove it from the computer using the notches near the input/output panel. Installing the Back Cover 1. Place the cover on the back of the computer using the notches near the input/output panel. 2. Tighten the screws to secure the back cover to the computer. 3. Install the VESA stand. 4. Follow the procedures in After Working Inside Your Computer. Removing the Memory 1. Follow the procedures in Before Working Inside Your Computer. 2. Remove the: a) VESA stand b) back cover
Résumé du contenu de la page N° 14
3. Lift the memory shield outwards. 4. Pry the retention clips away from the memory module until it pops up. Lift and remove the memory module from its connector. Installing the Memory 1. Align the notch on the memory-card with the tab in the system-board connector. 2. Press down on the memory module until the release tabs spring back to secure them in place. 3. Place the memory shield back into its place. 4. Install the: a) back cover b) VESA stand 5. Follow the procedures in After Working Ins
Résumé du contenu de la page N° 15
Installing the VESA Mount Bracket 1. Align and place the bracket on the back of the computer. 2. Tighten the screws to secure the VESA mount bracket to the computer. 3. Install the: a) back cover b) VESA stand 4. Follow the procedures in After Working Inside Your Computer. Removing the Touchscreen Board 1. Follow the procedures in Before Working Inside Your Computer. 2. Remove the: a) VESA stand b) back cover c) VESA mount bracket 3. Press the sides of the touchscreen-board shield to release the
Résumé du contenu de la page N° 16
Installing the Touchscreen Board 1. Tighten the screws to secure the touchscreen board to the chassis. 2. Connect all the touchscreen-board cables to the connectors on the touchscreen board and secure the latches. 3. Connect the system-board cable to the touchscreen-board cable connector. 4. Align and press the sides of touchscreen-board shield to secure the notches into the slots and snap the shield into place. 5. Install: a) VESA mount bracket b) back cover c) VESA stand 6. Follow the procedu
Résumé du contenu de la page N° 17
4. Install the: a) back cover b) VESA stand 5. Follow the procedures in After Working Inside Your Computer. Removing the System-Board Shield 1. Follow the procedures in Before Working Inside Your Computer. 2. Remove the: a) VESA stand b) back cover c) VESA mount bracket 3. Remove the screws that secure the system-board shield to the computer. Lift the system-board shield away from the computer. Installing the System-Board Shield 1. Align and place the system-board shield on the back of the comp
Résumé du contenu de la page N° 18
c) system-board shield 3. Press the release latch away from the battery. The battery pops out from the socket; lift the coin-cell battery out of the computer. Installing the Coin-Cell Battery 1. Place the coin-cell battery into its slot on the system board. 2. Press the coin-cell battery downward until the release latch springs back into place and secures it. 3. Install: a) system-board shield b) base cover c) VESA stand 4. Follow the procedures in After Working Inside Your Computer. Removing t
Résumé du contenu de la page N° 19
5. Lift the optical drive from the computer. 6. Remove the screws that secure the optical-drive bracket to the optical drive. Remove the optical-drive bracket from the optical drive. 19
Résumé du contenu de la page N° 20
Installing the Optical Drive 1. Place the optical-drive bracket on the optical drive. 2. Tighten the screws that secure the optical-drive bracket to the optical drive. 3. Align and slide the optical drive into its slot. 4. Connect the optical-drive cable. 5. Tighten the screws that secure the optical drive to the computer. 6. Install the: a) VESA mount bracket b) back cover c) VESA stand 7. Follow the procedures in After Working Inside Your Computer. Removing the Hard Drive 1. Follow the procedu
