Résumé du contenu de la page N° 1
Touchcomputer User Guide
19R SERIES 19-inch LCD Multifunction Touchcomputer
Résumé du contenu de la page N° 2
Elo TouchSystems Touchcomputer User Guide 19" LCD Multifunction Touchcomputer 19R series Revision A P/N E065202 Elo TouchSystems 1-800-ELOTOUCH (1-800-356-8682) www.elotouch.com
Résumé du contenu de la page N° 3
Copyright © 2009 Tyco Electronics. All Rights Reserved. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language or computer language, in any form or by any means, including, but not limited to, electronic, magnetic, optical, chemical, manual, or otherwise without prior written permission of Elo TouchSystems. Disclaimer The information in this document is subject to change without notice. Elo TouchSystems makes no re
Résumé du contenu de la page N° 4
Table of Contents Setup 5 Desktop 22 Unpacking Your Touchcomputer 5 Maintenance 23 Product Overview 6 Care and Handling 23 Front View 6 Warning 24 Rear View 6 Waste Electrical and Electronic Side View 7 Equipment (WEEE) Directive 24 Base Bottom View 7 Technical Specifications 25 Display Orientation 8 Touchcomputer Specifications 25 Initial Connections 9 Dimensional Diagrams 25 Standard Unit: 9 Front 25 Advanced Unit: 9 VESA 26 Initial Power-On 10 Rear 26 Language Selection 10 Base Mounting 27 Te
Résumé du contenu de la page N° 5
C H A P T E R 1 Setup This chapter discusses how to set up and test your Touchcomputer and any included peripheral options. Unpacking Your Touchcomputer Check that the following items are present and in good condition: OR Touchcomputer Power cable US/Canadian European power cable Quick Install Guide & CD/DVD Power Adapter Elo TouchSystems 19R series User Guide 5
Résumé du contenu de la page N° 6
Product Overview Front View Rear View Elo TouchSystems 19R series User Guide 6
Résumé du contenu de la page N° 7
Side View Base Bottom View Elo TouchSystems 19R series User Guide 7
Résumé du contenu de la page N° 8
Display Orientation Elo TouchSystems 19R series User Guide 8
Résumé du contenu de la page N° 9
Initial Connections Prior to turning on your Touchcomputer you must take the power adapter and appropri- ate power cable from the accessories box. Plug the small round plug with four pins into the 12Vdc power input on the Touchcomputer. Plug the power cable into the power adapter and the other end into a suitable power outlet (mains). Make sure the audio jumper cable and video jumper cable are in place as shown below. Standard Unit: Intel: Integrated Dual-core Intel® Atom™ 1.6 GHz processor
Résumé du contenu de la page N° 10
Initial Power-On The initial setup of the operating system takes approximately 5-10 minutes. Additional time may be needed depending on touchcomputer hardware configuration and con- nected devices. To setup the Windows Operating System (OS) for the touchcomputer, turn on the touchcomputer and follow the instructions on the screen. Language Selection When the following window appears, you have the option of changing the language used in menus and dialogs. Click Customize. The Regional and Languag
Résumé du contenu de la page N° 11
Time-zone selection When the following window appears, you may change the time-zone, date, and/or time of the touchcomputer. After making any changes, click Next to finish. Windows Setup will complete the initialization of the touchcomputer. Test Devices Testing the Touchscreen The touchscreen is pre-calibrated for accurate touch response. Elo TouchSystems 19R series User Guide 11
Résumé du contenu de la page N° 12
Calibration* If for any reason the touchscreen needs to be re-calibrated, go to the control panel and double-click the Elo Touchscreen icon. The window shown below will open. Click on the Align button. This launches the align/calibration program. A window similar to the one shown below will open. Follow the instructions to align/calibrate the touchscreen. *The alignment/calibration procedure may vary between touch technologies. Elo TouchSystems 19R series User Guide 12
Résumé du contenu de la page N° 13
C H A P T E R 2 Operation This chapter shows the user how to: control the On-Screen Display (OSD) and Power buttons, use the I/O panel, securely mount the Touchcomputer and adjust the display head. MENU UP / INCREASE DOWN / DECREASE SELECT POWER Elo TouchSystems 19R series User Guide 13
Résumé du contenu de la page N° 14
Side Panel Controls All adjustments made to the display via OSD and Power controls are automatically saved. User settings will remain unchanged after powering off/on or in the case of a power failure. Control Function 1. Menu/Exit Opens On Screen Display (OSD) / Exits the OSD menu 2. Up 1. Enter contrast adjustment 2. Increase value of the selected item. 3. Move OSD selection clockwise. 3. Down 1. Enter brightness adjustment 2. Decrease value of the adjustment item. 3. Move OSD selection count
Résumé du contenu de la page N° 15
The OSD shall control the following audio and screen characteristics: PARAMETER ADJUSTMENT Auto Adjust Automatically adjusts the system clock to the input video signal. Luminance Brightness Adjusts the Brightness signal from 0 (minimum brightness) to 100 (maximum brightness). Default: 100 (maximum brightness) Contrast Adjusts the contrast of the video signal from 0 (minimum) to 100 (maximum). Default: 50. Image setting H-position Moves the image horizontally in single-pixel increments on a scale
Résumé du contenu de la page N° 16
Miscellaneous Aspect Ratio Select between “Fill Screen” (input image is scaled to fill the LCD vertically and horizontally with no over- or under-scan) and “Fill to Aspect Ratio” (for input images with aspect ratio lower than the LCD panel’s aspect ratio of 16:10, input image is scaled to preserve input aspect ratio with no over-scan, & the unused portions of the panel will be black). Default: Fill Screen. Sharpness Adjusts sharpness of video signals on a scale from 1 to 5 using steps. Default:
Résumé du contenu de la page N° 17
Power Control Power Button The power button function can be set by the operating system under: Control Panel->Display Properties->Screen Saver->Power->Advanced->Power Buttons. To override all Operating System settings and shut down the Touchcomputer, press and hold the power button for 4-5 seconds. Note: On select models the delay to override the operating system is extended to 15 seconds. Elo TouchSystems 19R series User Guide 17
Résumé du contenu de la page N° 18
Using the I/O panel The Touchcomputer provides the following I/O interfaces for connecting a wide vari- ety of compliant devices. Standard Unit: Intel® Desktop Board D945GCLF2 VGA There is one VGA (HD-15) port (normally connected with supplied jumper cable to display VGA input). USB There are four USB 2.0 type A ports. Ethernet There is one RJ45 Ethernet port providing LAN capabilities. Serial There is one RS232 serial port. Microphone Input There is one 3.5 mm microphone input jack for connecti
Résumé du contenu de la page N° 19
Advanced Unit: Intel® Desktop Board D MS9820 VGA There is one VGA (HD-15) port (normally connected with supplied jumper cable to display VGA input). USB There are four USB 2.0 type A ports. Ethernet There are 2 RJ45 Ethernet ports providing LAN capabilities. Serial There is one RS232 serial port. Microphone Input There is one 3.5 mm microphone input jack for connecting an external microphone. Audio Output There is one 3.5 mm stereo audio output jack for connecting headphones, normally connected
Résumé du contenu de la page N° 20
Kensington Lock The Kensington lock is a security device that prevents theft. To find out more about this security device, look for Computer Locks on the Kensington website at: http:// www.kensington.com. Elo TouchSystems 19R series User Guide 20
