Résumé du contenu de la page N° 1
®
GPSMAP 4000/5000 SerieS i nSt AllA tion i nStructionS
The GPSMAP 4000/5000 series chartplotter and GPS 17 antenna must be properly installed according to the following instructions. You
need the appropriate fasteners, tools, and mounts listed in each section. These items are available at most marine dealers. Always wear safety
goggles, ear protection, and a dust mask when drilling, cutting, or sanding. When drilling or cutting, always check what is on the opposite side
of the surface. Mount
Résumé du contenu de la page N° 2
To install the bail mount and unit: 1. Usingthe bail mountas a template,mark the locationof the fourmounting holes. Be sureto leave at least5" (12.7 cm)of clearance behind the unit for thewiring. 1 3 " NoTE: Mount a 4008/4208/5008/5208 unit 31 / " (80 cm), and a 4012/4212/5012/5212 unit 39 / from a magnetic compass to avoid interference. 4 8 2. Usingan appropriately sizeddrill bit, drill the pilot holes foryour mounting hardware. 3. Secure the bail mount
Résumé du contenu de la page N° 3
To flush mount the unit: 1. The flush mount template is included in the product box. T rim the template and ensure it will fit in the location you want to flush mount the unit. NoTE: Make sure the surface on which you mount the unit has at least 7" (17.75 cm) of open space behind it to fit the unit and the connected wires. 1 NoTE: Make sure to leave approximately / " (13 mm) of space on the right side of the unit to access the SD card door. 2 1 3 " NoTE: Mount a 4008/4208/5008/52
Résumé du contenu de la page N° 4
Mounting the GPS 17 Antenna Either flush mount the GPS 17 Antenna or install it on on any standard 1" O. D. 14 threads-per-inch marine mount. When mounting the GPS 17, the cable can be run externally, through the mounting surface, or through the center of the marine ABOVE - BEST ABOVE - BEST mount. The GPS 17 connects to the 19-pin NMEA 0183 cable on the GPSMAP 4000/5000 series unit and provides the GPS/WAAS signal to the unit. If two BELOW - OK BELOW - OK 3' (1 m) 3' (1 m) or more Garmin
Résumé du contenu de la page N° 5
To attach the enclosed pole mount adapter to the GPS 17: To mount the GPS 17 with the cable run outside the 1. Thread the cable though the pole mount adapter. mount: 1. Place the cablein the verticalslot alongthe base of the 2. Alignthe tab on the polemount adapter to the notch onthe assembledGPS 17 and pole mount adapter. GPS17. 2. Screw the assembledGPS 17 and polemount adapter onto 3. Usethe enclosed screws tosecure the polemount
Résumé du contenu de la page N° 6
Wiring and Cables The GPSMAP 4000/5000 series unit comes with a power cable, a 19-pin NMEA 0183 data cable, and a 17-pin Marine Video cable. Optional Garmin Marine Network components use specialized Garmin Network cables. Depending on the installation, it may be necessary to drill holes to route the connector end of these cables. Garmin rubber grommets are provided to cover these holes for a finished look. You may not need the grommets in some installations. The grommets do NOT create a water
Résumé du contenu de la page N° 7
Wiring the GPS 17 Antenna The GPS 17 antenna must be wired to the included 19-pin NMEA 0183 cable as well as to the boat’s power supply. Refer to the diagram below when wiring the GPS 17 to the 19-pin NMEA 0183 cable. Use 22 AWG shielded wiring for extended runs of wire to the NMEA 0183 cable or GPS 17 cable. Solder all connections and seal them with heat shrink tubing. NoTE: If you are using more than one Garmin chartplotter over a Garmin Marine Network, only wire one chartplotter to a GPS
Résumé du contenu de la page N° 8
x x x x x x x x The Garmin Marine Network Cable: • TheGarmin Marine Network Cablehas a locking ring thatsecures the cable to the chartplotter or marine network device. Because of the sizeof this locking ring, itis not connectedto the network cableat the factory tomake it easier to install onyour boat. • Oncethe cable is runto the chartplotteror networkdevice, snap the locking ring together aroundthe connector and insert the r
Résumé du contenu de la page N° 9
x x x x x x x x NMEA NMEA 0183 0183 CABLE CABLE GARMIN MARINE RADAR GSD 22 SOUNDER UNIT M MARINE ARINE N NETWORK ETWORK CABLE CABLE T TRANSDUCER RANSDUCER x xx xx xx xx xx xx xx xx x CABLE CABLE xxxxxxxxxxxxxxxxxxx TO TRANSDUCER GMS 10 MARINE NETWORK PORT EXPANDER GDL 30/30A XM WEATHER RECEIVER GPS 17 GARMIN GARMIN GPSMAP 3000 SERIES GPSMAP 4000/5000 SERIES CHARTPLOTTER CHARTPLOTTER ADDITIONAL NMEA 0183 DEVICES Connecting a GPSMAP 4000/5000 Series chartplotter to an existing Garmin
Résumé du contenu de la page N° 10
Wiring Additional NMEA 0183 Devices The NMEA 0183 data cable included with the GPSMAP 4000/5000 series chartplotter supports the NMEA 0183 standard, which is used to wire various NMEA 0183-compliant devices, such as VHF radios, NMEA instruments, autopilots, or a computer. The GPSMAP 4000/5000 series unit features four ports to receive NMEA 0183 data (RX ports), and two ports to send NMEA 0183 data (TX ports). Wire one NMEA 0183 device per RX port to send data to a 4000/5000 series unit, wire u
Résumé du contenu de la page N° 11
GPSMAP 4000/5000 Series NMEA 0183 Data Cable + - BATTERy 10-35 VDC WIRE WIRE SEE TABLE FOR WIRE COLORS FUSE 7.5A - 42V RED (POWER) RED (POWER) Garmin POWER BLACK (PWR GND) BLACK (PWR GND) CABLE NMEA 0183 GPSMAP 4000/5000 BLACK (DATA GND) BLACK (DATA GND) Compliant Device Series Unit RX / A(+) TX / A (+) NMEA 0183 CABLE RX / B(-) TX / B(-) TX / A(+) RX / A(+) > > TX / B(-) RX / B(-) > > Wiring to a Standard NMEA 0183-compliant Device with 2-way Communication + - BATTERy WIRE WIRE 10-35 VD
Résumé du contenu de la page N° 12
1 Wiring to an Optional Alarm The GPSMAP 4000/5000 series unit can be used with a lamp, a horn, or both, to sound or flash an alert when the unit displays a message. The alarm does not need to be wired for the 4000/5000 unit to function. The alarm circuit pulls low when the alarm sounds. The maximum current is 100 mA, and a relay is needed to limit the current from the unit to 100 mA. A switch can be installed to select between visual and audible alerts. + - BATTERy 10-35 VDC WIRE COLOR FUSE
Résumé du contenu de la page N° 13
Connecting to a NMEA 2000 Network The GPSMAP 4000/5000 series unit is NMEA 2000 certified, and can receive data from a NMEA 2000 network installed on the boat to show engine specific information on the Gauges section of the Information screen. Also, the unit can receive heading data from a heading sensor connected to an installed NMEA 2000 network. The 4000/5000 series unit features a male NMEA 2000 Micro-connector. Connect the unit to an installed NMEA 2000 network using a cable with a fema
Résumé du contenu de la page N° 14
Marine Video Cable The included Marine Video 17-pin cable allows input of NTSC (National Television System Committee)/PAL (Phase Alternate Line) composite video sources, and PC monitor output (4008/4208/5008/5208 = VGA output, 4012/4212/5012/5212 = XGA output). Marine Video inputs are only available on the chartplotter to which they are attached and will not transmit over the Garmin Marine Network. 1 & 2. VIDEO 1 and VIDEO 2 Inputs (RCA connectors) allow input from two separate NTSC/P AL c
Résumé du contenu de la page N° 15
Making the Final Connections to the GPSMAP 4000/5000 Unit Once the power cable and the GPS 17 antenna (as well as any optional Garmin Marine Network devices, NMEA 0183 devices, NMEA 2000 connections, or video connections) have been wired to the boat, the cables must be connected to the GPSMAP 4000/5000 series unit. There are seven connectors on the back of the unit, one for power, three for Garmin Marine Network devices, one for the NMEA 0183 cable, one for a NMEA 2000 cable, and one for the m
Résumé du contenu de la page N° 16
Updating the Unit Software Your GPSMAP 4000/5000 series unit may contain a software update SD card. If so, follow the instructions provided with the card. If a software update SD card is not included, visit www.garmin.com to make sure your chartplotter software is up-to-date. To determine the version of software on your unit, select or touch Configure > System > System Information. GPSMAP 4000/5000 Series Installation Instructions
Résumé du contenu de la page N° 17
GPS 17 Antenna Drilling Template Drill using a 11/64" (4.5 mm) drill bit Drill this 3/4" (19 mm) hole if the coax is going to be installed through the mounting panel. GPSMAP 4000/5000 Series Installation Instructions 7
Résumé du contenu de la page N° 18
© Copyright 2007 Garmin Ltd. or its subsidiaries Garmin International, Inc. 1200 E 151st Street, Olathe, Kansas 66062 USA Tel. 913/397.8200 Fax. 913/397.8282 Garmin (Europe) Ltd Liberty House, Hounsdown Business Park, Southampton, Hampshire, SO40 9RB UK. Tel. 44/0870.8501241 (outside the UK.) or 0808 2380000 (UK only) Fax. 44/0870.8501251 Garmin Corporation No. 68, Jangshu 2nd Road, Shijr, Taipei County, Taiwan Tel. 886/2.2642.9199 Fax. 886/2.2642.9099 Part Number 190-00779-02 Rev. C
