Instruction d'utilisation Ariens 939002 ST520

Instruction d'utilisation pour le dispositif Ariens 939002 ST520

Dispositif: Ariens 939002 ST520
Catégorie: Tondeuse
Fabricant: Ariens
Dimension: 2.91 MB
Date d'addition: 8/21/2013
Nombre des pages: 26
Imprimez l'instruction

Téléchargez

Comment utiliser?

Notre objectif consiste à vous assurer le plus rapide accès au contenu de l'instruction d'utilisation du dispositif Ariens 939002 ST520. En utilisant l'aperçu en ligne vous pouvez parcourir le sommaire et passer à la page où vous trouverez la résolution de votre problème avec Ariens 939002 ST520.

Pour votre confort

Si regarder l'instruction Ariens 939002 ST520 directement sur la page n'est pas confortable pour vous, vous pouvez profiter de deux solutions possibles:

  • Exploration au mode de plein écran - pour analyser l'instruction d'une manière commode (sans l'avoir téléchargée sur votre ordinateur) vous pouvez utiliser le mode d'exploration en plein écran. Pour démarrer l'exploration de l'instruction Ariens 939002 ST520 en plein écran, utilisez le bouton Plein écran.
  • Téléchargement sur l'ordinateur - vous pouvez aussi télécharger l'instruction Ariens 939002 ST520 sur votre ordinateur et la sauvegarder dans vos ressources. Si vous n'avez pas envie de gaspiller votre espace disque, vous pouvez toujours télécharger cette instruction du ManualsBase dans l'avenir.
Ariens 939002 ST520 Manuel d'utilisation - Online PDF
Advertisement
« Page 1 of 26 »
Advertisement
Version imprimée

Beaucoup de gens préfèrent de lire les documents dans la version imprimée et non pas sur l'écran. L'option d'impression de l'instruction est aussi prévue et vous pouvez en profiter en cliquant le lien ci-dessus - Imprimez l'instruction. Il n'est pas nécessaire d'imprimer toute l'instruction Ariens 939002 ST520 - on peut choisir des pages. Economisez le papier.

Résumés

Vous trouverez ci-dessous les annonces des contenus qui se trouvent sur les pages suivantes de l'instruction de Ariens 939002 ST520. Si vous voulez parcourir rapidement le contenu des pages suivantes de l'instruction, vous pouvez en profiter.

Résumés du contenu
Résumé du contenu de la page N° 1

Sno-Thro®
Owner/Operator Manual
Models
939001 – ST520E
939002 – ST520
ENGLISH
FRANÇAIS
00582600A 6/06
Printed in USA

Résumé du contenu de la page N° 2

TABLE OF CONTENTS SAFETY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 STORAGE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 SERVICE PARTS. . . . . . . . . . . . . . . . . . . . . . . . . . 20 CONTROLS AND FEATURES . . . . . . . . . . . . . . . . 9 ACCESSORIES . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Résumé du contenu de la page N° 3

1. Read and understand all assembly instructions in 3. Review control functions and operation of the this manual. If you do not understand or have unit. Do not operate the Sno-Thro unless all difficulty following the instructions, contact your controls function as described in this manual. nearest Ariens Dealer for assistance. Make sure 4. Review recommended lubrication, maintenance all assembly has been properly completed. and adjustments. NOTE: To locate your nearest Ariens Dealer, go to

Résumé du contenu de la page N° 4

1. WARNING! 3. DANGER! Read Owner/Operator Manual. ROTATING PARTS. Keep clear of auger while engine is running. OL1801 � Read Operator’s Manual. OS2080 � Allow operation only by properly Keep people away from unit while trained adult, never children. operating. Keep children out of work � Stop engine and remove ignition area and under watchful care of a OL4370 key prior to leaving the operator’s responsible adult. position for any reason. � Keep all controls, guards and Never direct dis

Résumé du contenu de la page N° 5

NEVER operate unit after or during the use of Use only approved extension cords and receptacles medication, drugs or alcohol. Safe operation requires when starting units equipped with electric starter. DO your complete and unimpaired attention at all times. NOT connect electric starter cord to any wiring system that is not a three-wire grounded system. NEVER allow anyone to operate this unit when their alertness or coordination is impaired. ALWAYS allow unit and engine to adjust to outdoor

Résumé du contenu de la page N° 6

Keep unit free of ice or other debris. Clean up oil or fuel Before tipping unit up onto housing, remove fuel so no spills. spills will occur. Ensure unit is secure and will not tip over during maintenance. This product is equipped with an internal combustion type engine. DO NOT use unit on or near any ALWAYS keep protective structures, guards, and unimproved, forest-covered or brush covered land panels in good repair, in place and securely fastened. unless exhaust system is equipped with a

Résumé du contenu de la page N° 7

ASSEMBLY 1 WARNING: AVOID INJURY. Read and 1 understand the entire Safety section before proceeding. WARNING: Dropping or tipping over boxed unit could result in personal injury or damage to unit. PACKAGE CONTENTS 2 2 1 3 3 1. Lower 3.Upper Handlebar Handlebar 2. Hardware OS7035 Figure 4 Install Discharge Chute (Figure 5) 1. Grease underside of discharge chute ring (if not already greased). 2. Remove mounting hardware from the bottom of the chute pedestal. 4 3. Install discharge chute o

Résumé du contenu de la page N° 8

Check Tire Pressure Check Function of all Controls Check tire pressure and adjust to the pressure listed on Ensure unit runs and performs properly. Refer to tire sidewall. Operation. Check Auger Gearcase Oil Run-in Attachment Belt Check oil level in auger gearcase (see Check Auger 1. Start unit in a well-ventilated area according to Gearcase on page 14). Starting and Shut Off on page 12. 2. Engage attachment clutch lever and run Check Engine Crankcase Oil attachment for about 15 minutes. IMPO

Résumé du contenu de la page N° 9

CONTROLS AND FEATURES 1. Attachment Clutch Lever 1 2 2. Traction Drive Clutch Lever 3. Chute Handle (939001, 002) 4. Discharge Chute Deflector 3 5. Discharge Chute 6. Impeller 4 7. Auger 5 8. Scraper Blade 23 6 9. Auger Gearcase 10. Clean-out Tool 7 13 11. Oil Fill and Dipstick 12. Gas Tank and Cap 11 13. Electric Starter (939001) 14. Recoil Starter Handle 15. Primer Bulb 8 16. Oil Drain Plug 22 9 17. Throttle (Engine Stop) 10 21 18. Ignition Switch (push-pull) 19. Choke 20. Spark Plug and Wire

Résumé du contenu de la page N° 10

OPERATION Primer Bulb WARNING: AVOID INJURY. Read and Pushing the primer bulb in adds fuel for understand the entire Safety section before easier engine start. Refer to Starting and proceeding. Shut Off on page 12. OS1321 WARNING: To avoid injury to hands and feet, Choke Control Knob always disengage clutches, shut off engine, and wait for all movement to stop before 1. Choke Closed position: chokes off unclogging or working on snow thrower. air to engine for easier start. Keep hands and

Résumé du contenu de la page N° 11

To clear the discharge chute: FILLING FUEL TANK 1. Shut off the engine. WARNING: AVOID INJURY. Read and 2. Wait 10 seconds and make sure impeller blades understand the entire Safety section before have stopped rotating. proceeding. 3. Remove the snow clean-out tool (1) from the To add fuel to fuel tank: auger housing and use it to remove the clog from 1. ALWAYS place unit in open or well-ventilated the discharge chute. area. 4. Replace the snow clean-out tool on the auger 2. Stop engine

Résumé du contenu de la page N° 12

4. Make sure that the traction clutch and attachment TO STOP IN AN EMERGENCY drive clutch levers are fully disengaged. Immediately release both control levers to stop unit in an emergency. Stop engine, remove key and wait for 5. Push Primer Bulb 2 or 3 times for cold engine. all rotating parts to stop before leaving operator’s NOTE: When temperature is below -15° F (-26° C) position. additional priming may be needed. 6. Insert key into ignition switch on engine and push STARTING AND SHUT OF

Résumé du contenu de la page N° 13

Tips for Operation TRAVELING Snow is best removed as soon as possible after snow To travel from one work area to another: fall. 1. Set Throttle to Slow or Part-Throttle position. To clear an area, run unit in an overlapping series of 2. Press down on handlebars enough to raise front paths. For large areas, start in the middle and throw of unit slightly off surface. snow to each side, so snow is not cleared more than 3. Disengage traction drive clutch and push unit to once. new work area. AL

Résumé du contenu de la page N° 14

MAINTENANCE SCHEDULE CHECK ENGINE OIL The chart below shows the recommended The engine crankcase oil should be checked every 5 maintenance schedule that should be performed on a hours of operation. Oil level MUST be maintained in regular basis. More frequent service may be required. safe operating range on dipstick at all times or engine damage will result (See Engine Manual). Park unit on a level surface. Refer to Engine Manual for MAINTENANCE SCHEDULE detailed instructions. Service Each

Résumé du contenu de la page N° 15

IMPORTANT: DO NOT allow grease or oil to get on the belts. NOTE: Apply Ariens Hi-Temp Grease or equivalent to Grease Oil the lubrication fittings. See SERVICE PARTS on page 20. Sno-Thro should be lubricated (Figure 10) at beginning of season or every 25 operating hours. Auger Shaft NOTE: To grease auger shaft, remove shear bolt nuts, and shear bolts. Apply grease at the grease zerks and then turn the auger shaft. Replace shear bolts per instructions in Shear Bolts on page 15. Figure 10 OS

Résumé du contenu de la page N° 16

For Replacement: ATTACHMENT CLUTCH/BRAKE 1. Align shear bolt holes in auger with shear bolt ADJUSTMENT holes in the shaft. WARNING: IMPROPER ADJUSTMENT 2. Drive shear bolt through hole (if shear bolt was could result in unexpected movement of broken this will drive remaining part from shaft). auger and impeller causing death or serious injury. AUGER / IMPELLER MUST STOP 3. Secure shear bolt with nut. within 3 seconds when Attachment NOTE: DO NOT overtighten the shear bolt. Tighten Clutch

Résumé du contenu de la page N° 17

1 3 2 2 1 1/16 in. (1.6 mm) 1.Drive Brake 2.Brake Shoe and Pad Figure 17 7. Repeat steps 5 – 6 until attachment clutch lever distance and brake contact are correct. IMPORTANT: If attachment clutch/brake cannot be 1.Attachment Clutch Cable adjusted within tolerances, see your Dealer for repairs. 2.Jam Nut 3. Adjustment Barrel 8. Check belt finger clearance. With clutch lever engaged, belt fingers should be Figure 16 positioned as shown in Figure 22. Adjust belt 3. Check attachment clutch leve

Résumé du contenu de la page N° 18

To adjust traction clutch (Figure 19): 5. Remove top two cap screws and loosen lower two cap screws holding blower housing to frame 1. Loosen jam nut on traction clutch cable (one on each side). adjustment barrel. 6. Remove attachment drive belt from engine Turn adjustment barrel up the cable to decrease sheave (it may be necessary to turn engine the distance between clutch lever and handlebar. sheave using recoil starter handle). Turn the adjustment barrel down the cable to 7. Separate h

Résumé du contenu de la page N° 19

TRACTION DRIVE BELT REPLACEMENT 2 3 NOTE: Housing and frame must be tipped apart and 1 attachment drive belt removed from engine sheave in order to change traction drive belt (Figures 20 and 21). CAUTION: Always support Sno-Thro frame 6 and blower housing when loosening the cap screws holding them together. Never loosen cap screws while unit is in service position. 6 1. Shut off engine, remove key, disconnect spark plug wire and allow unit to cool completely. 2. Remove attachment drive bel

Résumé du contenu de la page N° 20

8. Replace attachment drive belt (See Replace SERVICE PARTS Attachment Drive Belt on page 18). Order the following parts through your Dealer: 9. Check traction drive clutch adjustment. See Traction Drive Clutch Adjustment on page 17. Part No. Description 00036800 Ariens Hi-Temp Grease (3, 3 oz. STORAGE cartridges) 21533400 Spark Plug (939001, 002) WARNING: AVOID INJURY. Read and 07200108 Impeller Belt understand the entire Safety section before proceeding. 07200109 Stretch Fit Traction Be


Instructions pareilles
# Instruction d'utilisation Catégorie Téléchargez
1 Ariens 311 Manuel d'utilisation Tondeuse 21
2 Ariens 070 - Professional G, 071 - Professional G, 072 - Professional G Manuel d'utilisation Tondeuse 3
3 Ariens 475 Manuel d'utilisation Tondeuse 4
4 Ariens 064 Manuel d'utilisation Tondeuse 4
5 Ariens 467-469 Manuel d'utilisation Tondeuse 3
6 Ariens 304 Manuel d'utilisation Tondeuse 2
7 Ariens 010-1540 Manuel d'utilisation Tondeuse 8
8 Ariens 511 Manuel d'utilisation Tondeuse 2
9 Ariens 067-073 Manuel d'utilisation Tondeuse 0
10 Ariens 911044-062 Manuel d'utilisation Tondeuse 16
11 Ariens 911099, 911101, 911102, 911330, 911331, 911514, 911515, 911525, 911526, 911531 Manuel d'utilisation Tondeuse 48
12 Ariens 911110 - SP21 Manuel d'utilisation Tondeuse 6
13 Ariens 911099 - LM21SH Manuel d'utilisation Tondeuse 8
14 Ariens 911094 - Pro 21SCH, 911095 - Pro 21CH, 911098 - LM21S, 911100 - LM21SW, 911394 - Pro 21SCH Manuel d'utilisation Tondeuse 8
15 Ariens 911110 - P 21LM Manuel d'utilisation Tondeuse 2
16 2Wire 7-1/4 Inch Circular Saw 94245 Manuel d'utilisation Tondeuse 3
17 Agilent Technologies E4371A Manuel d'utilisation Tondeuse 0
18 Agilent Technologies E4370A Manuel d'utilisation Tondeuse 3
19 Agilent Technologies E4374A Manuel d'utilisation Tondeuse 1
20 Adams 22 Manuel d'utilisation Tondeuse 1