Instruction d'utilisation Flymo VENTURER 320

Résumé du contenu de la page N° 1

For all customer enquiries or for replacement parts, contact:-
☎ ☎ 01325 300303
www.flymo.com
eop.customer.services@electrolux.co.uk
IMPORTANT INFORMATION
Read before use
& retain for future reference

Résumé du contenu de la page N° 2

Carton Contents start/stop lever switchbox cable clip lock off button washer nut upper handle bolt plastic handle lower handles knob grassbox upper safety flap grassbox lower lower handle fixing screws electric cable with motor cover moulded on plug spanner/scraper tool wheel assembly (x2) roller & rear height adjustment assembly instruction deck (1 lever each side) manual IMPORTANT ! Please check the contents of the carton are correct BEFORE assembling your new Flymo product. IF ANY PARTS AR

Résumé du contenu de la page N° 3

General 4. Replace worn or damaged blades together with 1. Never allow children or people unfamiliar with their fixings in sets to preserve balance. these instructions to use the mower. Local reg- Use ulations may restrict the age of the operator. 1. Use the lawnmower only in daylight or good 2. Only use the lawnmower in the manner and for artificial light. the functions described in these instructions. 2. Avoid operating your lawnmower in wet grass, 3. Never operate the lawnmower when you are w

Résumé du contenu de la page N° 4

CABLES MAINS PLUG REPLACEMENT IMPORTANT IMPORTANT 2 • Use only 1.00mm size cable up to 40 metres • If the plug supplied is cut off it should be length maximum. destroyed. There is an electric shock hazard if Maximum rating : a cut off plug is inserted into a 13 amp socket. 2 1.00mm size cable, 10 amps 250 volts AC. 1. No earth required. Flymo products are double • THE VENTURER 320 IS SUPPLIED WITH CABLE insulated to EN60335 and under no circumstances WIRED DIRECTLY INTO THE PRODUCT. shoul

Résumé du contenu de la page N° 5

Cutting Height Adjustment E Wheels - Front Cutting Height Adjustment • Height of cut is adjusted by raising or lower- ing the front wheels and rear roller. • NOTE The wheels and the roller must be adjusted to the same position: HEIGHT OF CUT WHEEL ROLLER Low Hole 1 Position H to remove to fit Medium Hole 2 Position J turn anti-clockwise turn clockwise High Hole 3 Position K • NOTE F A medium height of cut is recommended for wheel most lawns. mounting 1. To remove the wheel assembly turn the whe

Résumé du contenu de la page N° 6

Starting and Stopping To Start your Lawnmower M N 1. Form loop in mains cable and push the loop through the slot. (M) 2. To secure, position loop over the hook and pull the cable back through the slot (N). 3. Connect plug to mains and switch on. 4. Tilt the handle downwards to slightly raise the front of the lawnmower and to reduce the risk of lawn damage whilst starting. The switchbox is provided with a lock-off button P Q (P1) to prevent accidental starting. 5. Press and hold the lock-off butt

Résumé du contenu de la page N° 7

Caring for your Lawnmower Cleaning (U) • USE GLOVES U • IMPORTANT It is very important that you keep your lawnmower clean. Grass clippings left in any of the air intakes or under the deck could become a potential fire hazard. 1. Remove grass from under the deck with brush. 2. Using a soft brush - remove grass clippings from all air intakes, the discharge chute and the grass box. 3. Remove the blade, see Figure T, to gain access to the fan and clean with a soft brush. 4. Wipe over the surface of

Résumé du contenu de la page N° 8

Environmental Information The symbol on the product or on its packaging indicates that this product may not be treated as household waste. Instead it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment. By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the envi- ronment and human health, which could otherwise be caused by inappropriate waste handling of this product.