Résumé du contenu de la page N° 1
PO Box 1200
305 Commerce Drive
Winfield, Alabama 35594
ROTARY MOWER
OPERATION AND PARTS
MANUAL
www.kingkutter.com
Part No 999998
Résumé du contenu de la page N° 2
Résumé du contenu de la page N° 3
TO THE PURCHASER This manual contains valuable information about your new King Kutter Mower. It has been carefully prepared to give you helpful suggestions for operating, adjusting, ser- vicing and ordering repair parts. Keep this manual in a convenient place for quick and easy reference. Study it carefully. You have purchased a de- pendable and sturdy mower, but only by proper care and op- eration can you expect to receive the service and long life designed and built into it. S
Résumé du contenu de la page N° 4
It is the purchaser and/or operator’s responsibility to…. Read and understand the information contained in this manual. Operate, lubricate, assemble and maintain the equipment in accordance with all instructions and safety procedures in this manual. Inspect the equipment and replace or repair any parts that are damaged or worn which under contin- ued operation would cause damage, wear to other parts, or cause a safety hazard. Return the equipment or parts to the authoriz
Résumé du contenu de la page N° 5
CONTENTS ITEM PAGE Safety ......................................................................... 6 Assembly Instructions ................................................ 8 Before Putting Into Service ...................................... 11 Safety Training ......................................................... 12 Operational Safety ................................................... 14 Transportation Safety ............................................... 16 Attaching To Tractor
Résumé du contenu de la page N° 6
SAFETY READ AND FOLLOW THE INSTRUC- TIONS IN THIS MANUAL AND ESPE- CIALLY IN THE SAFETY SECTION. FAILURE TO DO SO CAN RESULT IN SERIOUS INJURY OR DEATH. TAKE NOTE! THIS SAFETY ALERT SYMBOL FOUND THROUGHOUT THIS MANUAL IS USED TO CALL YOUR ATTENTION TO INSTRUC- THIS SYMBOL MEANS TIONS INVOLVING YOUR PERSONAL ATTENTION! SAFETY AND THE SAFETY OF OTH- BECOME ALERT! YOUR SAFTEY IS INVOLVED ERS. SIGNAL WORDS: The signal words DANGER, WARNING and CAUTION are used with the safety me
Résumé du contenu de la page N° 7
EQUIPMENT SAFETY GUIDELINES Safety of the operator and by standards is one of the main concerns in designing and devel- oping a mower. However, every year accidents occur which could have been avoided by a few seconds of thought and a more careful approach to handling equipment. You, the op- erator, can avoid many accidents by observing the following precautions and insist those working with you, or for you, follow them. In order to provide a better view, certain photographs or i
Résumé du contenu de la page N° 8
ROTARY MOWER ASSEMBLY INSTRUCTIONS STEP 1 Place rotary mower on a flat, level surface. (See Figure A) STEP 2 Remove the wired on PTO shaft, lift pins, and spacers. Loosen and remove the (4) bolts on the lift arm brackets, that secure the lift arm support straps, lift arms, and lift arm braces from the shipping positions and set aside. (See Figure B) STEP 3 Install the right lift arm and lift arm support strap using (2) two short bolts and (1) one lift pin. (See Figure C) Note:
Résumé du contenu de la page N° 9
STEP 7 Using the right side lift arm as a lever, pull to the outside of the lift arm bracket and inset bolt through lift arm and lift arm bracket. (See Figure I) Install washer and nut. Place the lift pin in the larger of the (2) holes on the lift arm brace and loosely attach the lift arm. Finally insert bolt, nut and washer to lower section of lift arm support strap to lift arm bracket. (See Figure J) STEP 8 Tighten all nuts and bolts. Figure A Figure B Figure C Figure D 9
Résumé du contenu de la page N° 10
Figure E Figure F Figure G Figure H Figure I Figure J 10
Résumé du contenu de la page N° 11
BEFORE PUTTING ROTARY MOWER INTO SERVICE (IMPORTANT-INSTRUCTIONS PRIOR TO START UP) SHIPPED WITH OIL IN GEARBOX SHIPPED WITHOUT GREASE IN GREASE FITTINGS. UNIT MUST BE SERVICED BEFORE USING. • Use Multi-Purpose Gear Oil (I.E. S.A.E. 80w/90 or S.A.E. 85w/140 Multi- purpose gear oil) in Gearbox. • For all Grease Fittings use TYPE/grade II tube grease. STEP 1 Place rotary mower so that the deck is secure and level. STEP 2 Remove 1/2” Pipe Plug (Located at top of gearbox) and 1/8” Pip
Résumé du contenu de la page N° 12
SAFETY TRAINING Safety is a primary concern in the design and manufacture of our product. Un- fortunately, our efforts to provide safe equipment can be wiped out by a single careless act of an operator or bystander. In addition to the design and configuration of equipment, hazard control and ac- cident prevention are dependent upon the awareness, concern, prudence and proper training of personnel involved in the operation, transport, maintenance and storage of this equipment.
Résumé du contenu de la page N° 13
PREPARTION Never operate the tractor and mower until you have read and completely under- stand this manual, the Tractor Operator’s Manual, and each of the safety mes- sages found on the safety signs on the tractor and mower. Personal protection equipment including hardhat, safety glasses, safety shoes, and gloves are recommended during assembly, installation, operation, adjustment, maintenance, repair- ing, removal, or moving the implement. Do not allow long hair, loose fitting clothi
Résumé du contenu de la page N° 14
OPERATIONAL SAFETY The use of this equipment is subject to certain hazards that cannot be protected against by the mechanical means or product design. All operators of this equip- ment must read and understand this entire manual, paying particular attention to safety and operating instructions, prior to using. If there is something in this manual you do not understand, ask your supervisor, or your dealer, to explain it to you. Most accidents occur because of neglect or carelessn
Résumé du contenu de la page N° 15
OPERATIONAL SAFETY continued... Never allow the cutting blade to con- tact such items. Cut material higher at first, allowing rotary mower to clear hidden objects. Never assume an area is clear. Always Check! Always stop the tractor, disengage PTO, set brake, shut off the tractor engine, remove the ignition key, lower implement to the ground and allow mower blades to come to a complete stop before dismounting tractor. Never leave equipment unattended with the tractor running.
Résumé du contenu de la page N° 16
OPERATIONAL SAFETY continued... Pass rotary mower diagonally through sharp dips and avoid sharp drops to pre- vent “hanging up” tractor and rotary mower. Practice will improve your skills in maneuvering on rough terrain. Always cut down slopes, never across the face. Always check tractor manual for proper use on slopes. When using a unit, a minimum 20% of tractor and equipment weight must be on tractor front wheels. Without this weight, tractor could tip over, causing personal i
Résumé du contenu de la page N° 17
ATTACHING TO TRACTOR WARNING Never stand between tractor and rotary mower while backing up tractor to the hitch. STEP 1 Attach to tractor's category 1 three point hitch as described in the Tractor's Operator’s Manual. WARNING Failure to install retaining clip on gearbox input shaft would allow driveline to swing freely if bolt is sheared causing possible injury or death. STEP 2 D
Résumé du contenu de la page N° 18
ATTACHING TO TRACTOR continued.... STEP 5 Place and hold inner PTO shaft section next to outer section and check if PTO shaft is too long. Each section should end approximately 3 inches short of reaching u-joint shield on the opposite section. If the shaft is too long measure 3 inches back from each u-joint shield and mark the other shaft section. Be sure to do this for both PTO shaft halves. NOTE: Do not cut PTO shaft sections at this time. STEP 6 Raise rotary mower and re
Résumé du contenu de la page N° 19
SIZING PTO SHAFT STEP 1 Cutting the PTO shaft to length. NOTE: Be sure to cut equal lengths of each PTO shaft section. Clamp end of PTO shaft in a vice and cut off shield where marked. (Figure 1-A & 1-B) Figure 1-A STEP 2 Using cut section of the shield as a guide cut shaft off the same amount. (Figure 2) STEP 3 Repeat steps 1 and 2 for other PTO shaft section. STEP 4 Figure 1-B Use a file to deburr PTO shafts. Clean up all chi
Résumé du contenu de la page N° 20
OPERATING INSTRUCTIONS This mower was designed to CUT PASTURE GRASS AND ROUGH AREAS UP TO 1" IN DIAMETER.. Use of your rotary mower to cut any material larger than 1" in diame- ter may damage the mower and void your warranty. PRE-OPERATIONAL ADJUSTMENTS Set tractor's lift control stop at a position that will prevent the PTO shaft from coming in contact with the front edge of the mower when it is at full lift. Consult your tractor manual for instructions. CUTTING HEIGHT ADJUS
