Résumé du contenu de la page N° 1
02478
182565 Rev. 1 3.18.02 MH/TR
Printed in U.S.A.
Résumé du contenu de la page N° 2
SAFETY RULES SAFE OPERATION PRACTICES FOR RIDE-ON MOWERS IMPORTANT: THIS CUTTING MACHINE IS CAPABLE OF AMPUTATING HANDS AND FEET AND THROWING OBJECTS. FAILURE TO OBSERVE THE FOLLOWING SAFETY INSTRUCTIONS COULD RESULT IN SERIOUS INJURY OR DEATH. Avoid starting or stopping on a slope. If tires lose traction, I. GENERAL OPERATION disengage the blades and proceed slowly straight down • Read, understand, and follow all instructions in the manual the slope. and on the machine before starting. On
Résumé du contenu de la page N° 3
SAFETY RULES Safe Operation Practices for Ride-On Mowers Look for this symbol to point out im- portant safety precautions. It means Be sure the area is clear of other people before mowing. CAUTION!!! BECOME ALERT!!! YOUR Stop machine if anyone enters the area. SAFETY IS INVOLVED. Never carry passengers or children even with the blades off. Do not mow in reverse unless absolutely necessary. Al- CAUTION: In order to prevent acciden- ways look down and behind before and while backing. ta
Résumé du contenu de la page N° 4
CONGRATULATIONS on your purchase of a new tractor. It PRODUCT SPECIFICATIONS has been designed, engineered and manufactured to give GASOLINE CAPACITY 2.0 GALLONS you the best possible dependability and performance. AND TYPE: UNLEADED REGULAR Should you experience any problem you cannot easily remedy, please contact your nearest authorized service OIL TYPE (API-SF-SJ): SAE 30 (above 32°F) center. We have competent, well-trained technicians and SAE 5W-30 (below 32°F) the proper tools to service
Résumé du contenu de la page N° 5
UNASSEMBLED PARTS Seat Steering Wheel Steering Wheel Insert (1) Washer 17/32 x 1-3/16 x 12 Gauge Steering Extension Shaft (1) Knob (1) Hex Bolt Steering 3/8-16 x 1 Sleeve Slope Sheet Steering Adapter (1) Large Flat Washer Key (2) Keys (1) Lock washer 3/8 (2) Mulch Blades (1) Locknut 5/16-18 (1) Oil Drain Tube (1) Hex Bolt 5/16-18 x 1-1/4 5
Résumé du contenu de la page N° 6
ASSEMBLY Your new tractor has been assembled at the factory with exception of those parts left unassembled for shipping purposes. To ensure safe and proper operation of your tractor all parts and hardware you assemble must be tightened securely. Use the correct tools as necessary to insure proper tightness. TOOLS REQUIRED FOR ASSEMBLY INSERT A socket wrench set will make assembly easier. Standard wrench sizes are listed. 3/8 HEX BOLT (2) 1/2" wrenches Utility knife 3/8 LOCK WASHER (1) 9/16"
Résumé du contenu de la page N° 7
ASSEMBLY INSTALL SEAT (See Fig. 3) NOTE: You may now roll or drive your tractor off the skid. Follow the appropriate instruction below to remove the Adjust seat before tightening adjustment knob. tractor from the skid. Remove adjustment knob and flat washer securing seat to cardboard packing and set aside for assembly of seat TO ROLL TRACTOR OFF SKID (See Operation to tractor. section, page 10, for location and function of Pivot seat upward and remove from the cardboard controls) packing. Re
Résumé du contenu de la page N° 8
ASSEMBLY CHECK TIRE PRESSURE IMPORTANT: FOR SHIPPING PURPOSES, THE MULCHER PLATE WAS PREATTACHED TO YOUR The tires on your tractor were overinflated at the factory for MOWER. THE MULCHER PLATE MUST ONLY BE USED shipping purposes. Correct tire pressure is important for WITH THE MULCHING BLADES THAT CAME PACKED best cutting performance. SEPARATELY IN THE CARTON. Reduce tire pressure to PSI shown in “PRODUCT SPECIFICATIONS” section of this manual. YOUR MOWER CAME FACTORY EQUIPPED WITH HIGH PERFO
Résumé du contenu de la page N° 9
OPERATION These symbols may appear on your tractor or in literature supplied with the product. Learn and understand their meaning. BATTERY CAUTION OR REVERSE FORWARD FAST SLOW WARNING LIGHTS ON OVER TEMP ENGINE ON ENGINE OFF OIL PRESSURE LIGHT PARKING BRAKE UNLOCKED MOWER LIFT FUEL CHOKE MOWER HEIGHT LOCKED P ATTACHMENT REVERSE NEUTRAL HIGH LOW PARKING BRAKE CLUTCH ENGAGED 15 15 15 KEEP AREA CLEAR SLOPE HAZARDS ATTACHMENT (SEE SAFETY RULES SECTION) CLUTCH DISENGAGED IGNITION FREE WHEEL DANG
Résumé du contenu de la page N° 10
OPERATION KNOW YOUR TRACTOR READ THIS OWNER'S MANUAL AND SAFETY RULES BEFORE OPERATING YOUR TRACTOR Compare the illustrations with your tractor to familiarize yourself with the locations of various controls and adjustments. Save this manual for future reference. ATTACHMENT LIGHT IGNITION CLUTCH LEVER SWITCH SWITCH POSITION AMMETER LIFT LEVER PLUNGER THROTTLE/CHOKE CONTROL ATTACHMENT LIFT LEVER CLUTCH/ BRAKE PEDAL HEIGHT ADJUSTMENT KNOB PARKING BRAKE MOTION FREE WHEEL CONTROL CONTROL LEVER FIG.
Résumé du contenu de la page N° 11
OPERATION The operation of any tractor can result in foreign objects thrown into the eyes, which can result in severe eye damage. Always wear safety glasses or eye shields while operating your tractor or performing any adjustments or repairs. We recommend a wide vision safety mask over spectacles or standard safety glasses. IMPORTANT: LEAVING THE IGNITION SWITCH IN ANY HOW TO USE YOUR TRACTOR POSITION OTHER THAN "OFF" WILL CAUSE THE BATTERY TO BE DISCHARGED, (DEAD). TO SET PARKING BRAKE (See
Résumé du contenu de la page N° 12
OPERATION TO ADJUST GAUGE WHEELS (See Fig. 7) TO OPERATE ON HILLS Gauge wheels are properly adjusted when they are slightly off the ground when mower is at the desired cutting height in CAUTION: Do not drive up or down hills operating position. Gauge wheels then keep the deck in with slopes greater than 15° and do not proper position to help prevent scalping in most terrain drive across any slope. conditions. Choose the slowest speed before starting up or down NOTE:Adjust gauge wheels with
Résumé du contenu de la page N° 13
OPERATION Insert key into ignition and turn key clockwise to BEFORE STARTING THE ENGINE “START” position and release key as soon as engine starts. Do not run starter continuously for more than CHECK ENGINE OIL LEVEL fifteen seconds per minute. If the engine does not start The engine in your tractor has been shipped, from the after several attempts, move throttle control to fast factory, already filled with summer weight oil. position, wait a few minutes and try again. If engine still Chec
Résumé du contenu de la page N° 14
OPERATION Sitting in the tractor seat, start engine. After the engine is running, move throttle control to slow position. With motion control lever in neutral (N) position, slowly disengage clutch/brake pedal. Move motion control lever to full forward position and hold for five (5) seconds. Move lever to full reverse position and hold for five (5) seconds. Repeat this procedure three (3) times. NOTE: During this procedure there will be no movement of drive wheels. The air is being removed f
Résumé du contenu de la page N° 15
CUSTOMER RESPONSIBILITIES MAINTENANCE SCHEDULE FILL IN DATES AS YOU COMPLETE REGULAR SERVICE SERVICE DATES Check Brake Operation Check Tire Pressure Check Operator Presence and Interlock Systems T R Check for Loose Fasteners 5 A Sharpen/Replace Mower Blades 3 C Lubrication Chart T Check Battery Level 4 0 Clean Battery and Terminals R Check Transaxle Cooling Check V-Belts Check Engine Oil Level Change Engine Oil (with oil filter) 1,2 Change Engine Oil (without oil filter) 1,2 E Clean Air Filter N
Résumé du contenu de la page N° 16
CUSTOMER RESPONSIBILITIES TRACTOR MANDREL TRAILING ASSEMBLY EDGE UP Always observe safety rules when performing any mainte- BLADE nance. CENTER HOLE BRAKE OPERATION If tractor requires more than six (6) feet stopping distance at high speed in highest gear, then brake must be adjusted. (See “TO ADJUST BRAKE” in the Service and Adjustments section of this manual). LOCK WASHER STAR TIRES Maintain proper air pressure in all tires (See “PRODUCT SPECIFICATIONS” section of this manual). FLAT WASHER
Résumé du contenu de la page N° 17
CUSTOMER RESPONSIBILITIES NOTE: Although multi-viscosity oils (5W30, 10W30 etc.) NOTE: The original equipment battery on your tractor is improve starting in cold weather, these multi-viscosity oils maintenance free. Do not attempt to open or remove caps or will result in increased oil consumption when used above covers. Adding or checking level of electrolyte is not 32°F. Check your engine oil level more frequently to avoid necessary. possible engine damage from running low on oil. TO CLEAN BA
Résumé du contenu de la page N° 18
CUSTOMER RESPONSIBILITIES ENGINE COOLING FINS (See Fig. 16) COVER Remove any dust, dirt or oil from engine cooling fins to KNOB prevent engine damage from overheating. Remove oil fill cap/dipstick. CARTRIDGE Remove hex bolts from blower housing and lift housing NUT COVER off engine. Cover oil fill opening to prevent entry of dirt. Use compressed air or stiff bristle brush to thoroughly clean engine cooling fins. PAPER To reassemble, reverse above procedure. CARTRIDGE FOAM HEX BLOWER H
Résumé du contenu de la page N° 19
SERVICE AND ADJUSTMENTS CAUTION: BEFORE PERFORMING ANY SERVICE OR ADJUSTMENTS: Depress clutch/brake pedal fully and set parking brake. Place motion control lever in neutral (N) position. Place attachment clutch in “DISENGAGED” position. Turn ignition key “OFF” and remove key. Make sure the blades and all moving parts have completely stopped. Disconnect spark plug wire from spark plug and place wire where it cannot come in contact with plug. TRACTOR TO INSTALL MOWER (SEE FIG. X) R
Résumé du contenu de la page N° 20
SERVICE AND ADJUSTMENTS When distance “D” is 1/8" to 1/2" lower at front than rear, TO LEVEL MOWER HOUSING tighten nuts “F” against trunnion on both front links. Adjust the mower while tractor is parked on level ground or To raise front of mower, loosen nut “F” from trunnion on driveway. Make sure tires are properly inflated (See “PROD- both front links. Tighten nut “E” on both front links an UCT SPECIFICATIONS” section of this manual). If tires are equal number of turns. over or underinf
