Instruction d'utilisation Snapper 1695195

Résumé du contenu de la page N° 1

Sub-Frame Hitch
Installation
Mfg. No. 1695195
For Prestige / 1800 / 2800 & Conquest / 1700 / 2700 Series
Instructions
12
18
16
18
19
7 11 3
17
6
3
17
4
5
22
25
22
2
24
14
13
Hydraulic 15
Lift
8
9
10
21
Manual Lift
(Add to early models
already present on
23
current models)
20
3
1
Front Hole for Dozer Applications
Rear Hole for Snowthrower Applications
Kit Contents:
Ref Part No. Qty. Description Ref Part No. Qty. Description
1 1733779A 1 PUSH BAR ASSEMBLY 13 1722469 1 LOCKDOWN, HYD.
2 1733812 2 RO

Résumé du contenu de la page N° 2

Installation Instructions Sub-Frame Hitch NOTE: Please read through these instructions and the Assemble Lift Rod instructions of any other attachments before beginning 1. Install the set collars (B, Figure 3), spring (C), and installation. rod guide (D) on the lift rod (A) as shown. Final adjustment of the set collars will be made after the WARNING hitch and attachment are installed. Before beginning any service work turn off the PTO, set the parking brake, turn off the ignition, A and disconne

Résumé du contenu de la page N° 3

Sub-Frame Hitch Installation Instructions Snowthrower Snowthrower & Dozer & Dozer E Applications Applications A A B F C D C D E B Mower Mower G Applications Applications A A B F D F C G E Figure 5. Lift Lock Plate - Hydraulic Lift Models Figure 6. Lift Link - Manual Lift Models A. Lift Cylinder A. Pin B. Flat Head Pin (Original) B. Rear Hole of Lift Bar (Snowthrower/Dozer C. Flat Head Pin (New) Applications) D. Lock Plate C. Spacer E. Hair Pin Clips D. Hair Pin Clip F. Lift Shaft Assy. E. Upp

Résumé du contenu de la page N° 4

Installation Instructions Sub-Frame Hitch A B C D E Figure 7. Install Hitch A. J-Hooks D. Hook B. Hitch Rod E. Clamp Plate C. Hitch Rod 5. Push the clamp plate (D) backwards until it is snug Install Hitch against the lift shaft. Tighten the clamp plate hard- 1. Slide the hitch under the tractor. ware (E). 2. Raise the rear of the hitch and place the hook (C) over the lift shaft. 3. Connect the front of the hitch to the tractor J-hooks (A, Figure 7) using the hitch rod (B) and a safety clip i

Résumé du contenu de la page N° 5

Sub-Frame Hitch Installation Instructions Install Lift Rod D 1. Slide the lift lever (A, Figure 8) onto the end of the tractor lift shaft (B) under the right side footrest. 2. Use the tabs on the lift lever (A) to capture the tractor lift arm. Secure in place with a clevis pin (D) and safety clip (C). A B C Figure 8. Install Lift Lever A. Lift Lever B. Lift Shaft C. Safety Clip D. Clevis Pin 3. Insert the rear of the lift rod (B, Figure 9) into the bot- tom of the lift lever (A). Secure with

Résumé du contenu de la page N° 6

OBSOLETE Installation Instructions Sub-Frame Hitch C A B D E F A. Hitch Rod B. Hitch Rod C. Lift Lever D. Pressure Lock Plate (Manual) E. Pressure Lock Plate (Hydraulic) F. Hook Figure 10. Normal Installation & Removal REMOVAL NORMAL INSTALLATION NOTE: After removing components, reinstall the clevis 1. Insert the hook (F, Figure 10) into the back of the pins and clips to prevent loss. hitch. Mount the rear of the hitch on the lift cross- shaft. 1. Disconnect the lift rod from the attachment a

Résumé du contenu de la page N° 7

Sub-Frame Hitch Installation Instructions Snowthrower Snowthrower & Dozer & Dozer E Applications Applications A A B F C D C D E B Mower Mower G Applications Applications A A B F D F C G E Figure 11. Lift Lock Plate - Hydraulic Lift Models Figure 12. Lift Link - Manual Lift Models A. Lift Cylinder A. Pin B. Flat Head Pin (Original) B. Rear Hole of Lift Bar (Snowthrower/Dozer C. Flat Head Pin (New) Applications) D. Lock Plate C. Spacer E. Hair Pin Clips D. Hair Pin Clip F. Lift Shaft Assy. E.

Résumé du contenu de la page N° 8

Installation Instructions Sub-Frame Hitch DOWNWARD PRESSURE LOCK PLATE - OBSOLETE G Note:The following information applies only to models produced before October of 2002. It is being included here for reference pur- poses ONLY. F MANUAL LIFT MODELS 1. Rest the back of the lock plate (G, Figure 4) against the spacer (I) and rotate until it lines up with the hole in the lift bar (F). 2. Secure the lock plate (G) to the lift bar (F) using a flat head pin (C) and hair pin clip (H). A B C I D E F H