Résumé du contenu de la page N° 1
Safety Instructions & Operator’s Manual for
LAWN TRACTOR
HYDROSTATIC DRIVE
ELECTRIC CLUTCH
SERIES I
MODELS
LT180H42IBV2
WLT180H42IBV2
LT200H48IBV2
WLT200H48IBV2
MODEL NUMBER EXPLANATION
LT 180 H 42 I B V 2
MODEL DESIGNATION ENGINE OPTION
ENGINE HP ENGINE TYPE
DRIVE SYSTEM TYPE ENGINE MODEL
CUTTING WIDTH SERIES DESIGNATION
LT/WLT – Model Designation I – Series Designation
180 – 18.0 HP (Engine Horse Power) B – Briggs & Stratton Engine
200 – 20.0 H
Résumé du contenu de la page N° 2
IMPORTANT SAFETY INSTRUCTIONS WARNING: This powerful cutting machine is capable of amputating hands and feet and can throw objects that can cause injury and damage! Failure to comply with the following SAFETY instructions could result in serious injury or death to the operator or other persons. The owner of the machine must understand these instructions and must allow only persons who understand these instructions to operate machine. Each person operating the machine must be of sound mind
Résumé du contenu de la page N° 3
IMPORTANT SAFETY INSTRUCTIONS PREPARATION OPERATION (Continued From Previous Page) (Continued From Previous Column) 7. Keep people and pets out of mowing area. 14. Exercise CAUTION when pulling loads. Limit loads Immediately STOP blades, STOP engine, and to those you can safely control and attach loads to STOP machine if anyone enters the area. hitch plate as specified with SNAPPER attachment 8. Check shields, deflectors, switches, blade instructions. controls and other safety devic
Résumé du contenu de la page N° 4
TABLE OF CONTENTS IMPORTANT SAFETY INSTRUCTIONS.................. 2 - 3 SECTION 4 - ADJUSTMENTS & REPAIR..............16-33 Engine Adjustments & Repair .............................16 TABLE OF CONTENTS..................................................4 Mower Deck & Component Adjustments ...........16 Blade Brake Adjustment ......................................16 SECTION 1 - FAMILIARIZATION ...................................5 Blade Belt Adjustment...................................
Résumé du contenu de la page N° 5
Section 1 - FAMILIARIZATION LIGHT CLUTCH/BRAKE PEDAL SWITCH CHOKE PARK BRAKE BLADE SWITCH LEVER FAST SLOW DOWN BATTERY OPERATOR’S SEAT (UNDER SEAT) IGNITION ENGINE SPEED STEERING KEY CONTROL WHEEL SEAT ADJUSTMENT KNOB DASHBOARD CONTROLS (UNDER SEAT) FUEL TANK (UNDER HOOD) SPEED CONTROL LEVER HOOD OVERRIDE LEVER HEADLIGHTS CUTTING HEIGHT ADJUSTMENT LEVER DISCHARGE ENGINE
Résumé du contenu de la page N° 6
Section 2 - OPERATING INSTRUCTIONS 2.1 PRE-START CHECKLIST Make the following checks and perform service as required before each start-up. FUEL TANK 2.1.1. Check tires and add air as needed to bring pressure to 12 P.S.I. in front tires and 12 P.S.I. in rear tires. 2.1.2. Check guards, deflectors and covers to make sure all are in place and securely tightened. If guards are missing or damaged, replace BEFORE using mower. TIGHTEN CAP 2.1.3. Check engine o
Résumé du contenu de la page N° 7
Section 2 - OPERATING INSTRUCTIONS 2.3 STARTING & OPERATION 5. Choke engine for cold starting by moving engine 2.3.1. STARTING ENGINE speed control to "CHOKE" position. NOTE: Some models are equipped with a separate choke control, 1. Take a comfortable position in seat of machine, look around to make sure that the area you are going to located on the dash of the tractor. Pull the control “OUT” to choke position to start a cold engine. Little mow is clear of people, children and pets. T
Résumé du contenu de la page N° 8
Section 2 - OPERATING INSTRUCTIONS 2.3 STARTING & OPERATION (Continued) 2.4 STOPPING ENGINE, BLADE, WHEEL DRIVE 2.3.2. STARTING WHEEL DRIVE 2.4.1. STOPPING ENGINE 1. Shift speed control lever to neutral. 1. Stop engine by turning key to the "OFF" position. See Figure 2.9. 2. Start engine. Refer to Section “STARTING ENGINE”. 3. Release clutch/brake pedal. 4. Slowly shift speed control lever forward for forward motion or to the rear for reverse motion. See RUN OFF START Figure 2.7
Résumé du contenu de la page N° 9
Section 2 - OPERATING INSTRUCTIONS 2.4 STOPPING 2.4.5. RELEASING PARK BRAKE 2.4.3. STOPPING MOWER BLADES 1. Fully depress clutch/brake pedal. Move park brake lever “DOWN” to release park brake. Release 1. Stop mower blade by pushing blades switch IN to disengage blades. See Figure 2.11. clutch/brake pedal. See Figure 2.13. ON PUSH BLADE SWITCH IN TO PARK THE “OFF” POSITION CLUTCH/BRAKE BRAKE PEDAL LEVER OFF PULL BLADE SWITCH OUT TO THE “ON” POSITION FULLY DEPRESS CLUTCH
Résumé du contenu de la page N° 10
Section 2 - OPERATING INSTRUCTIONS 2.6. ROLLING TRACTOR WITH ENGINE OFF 2.6.1. Rolling Hydro Models 1. With engine "OFF", move to rear of tractor. 2. Pull the roll release control all the way out to disengage the hydro transmission. See Figure 2.15. PULL ROLL RELEASE WARNING CONTROL ALL THE WAY OUT TO DISENGAGE DO NOT disengage the hydro transmission and coast HYDRO TRANSMISSION down slopes. DO NOT use Roll Release Control to disengage hydro transm
Résumé du contenu de la page N° 11
Section 2 - OPERATING INSTRUCTIONS 2.7. REVERSE LOCKOUT MECHANISM 2.7.1. Reverse Lockout Mechanism Override 1. Stop machine. Stop blades. Data indicates that tragic back-over accidents occur 2. Depress and hold Override Lever. each year. These accidents usually involve unsupervised 3. Pull blade switch “OUT” to engage blade. children. Many times these children have been given 4. Release Override Lever rides on the machine and have been trained to view this potentially dangerous p
Résumé du contenu de la page N° 12
Section 3 – MAINTENANCE 3.1 INTRODUCTION 4. Check blade for straightness. Refer to Section To retain the quality of the Tractor, use genuine “ADJUSTING MOWER BLADE”. SNAPPER replacement parts only. Contact a local 5. Check torque of blade mounting bolts. Torque to: SNAPPER dealer for parts and service assistance. For 42" deck - 30 to 40 ft lbs. See Figure 3.2. the correct part or information for a particular Tractor, 48" deck - 70 to 80 ft lbs. always mention the model and serial numbe
Résumé du contenu de la page N° 13
Section 3 - MAINTENANCE WARNING AIR CLEANER DO NOT attempt any adjustments, maintenance, RETAINING BOLTS service or repairs with the engine running. Stop engine. Stop blade. Engage parking brake. Remove key. Remove spark plug wire from spark plug and secure away from plug. Engine and components are HOT. Avoid serious burns, allow all parts to cool before working on machine. AIR CLEANER COVER 3.2.4. CHECK DECK DRIVE BELT 1. The idler and spring provide pr
Résumé du contenu de la page N° 14
Section 3 - MAINTENANCE 3.3.2. MOWER COMPONENTS 3.3.4. TRACTOR LUBRICATION 1. Check deck drive belt for proper tension. Refer 3. Clutch/Brake Pivot to Section, “CHECK DECK DRIVE BELT”. The clutch/brake pivot is located on the L.H. underside of the tractor and is lubricated with one 2. Check blades for sharpness, wear, damage and torque. Refer to Section on “MOWER BLADE shot of general purpose grease. See Figure 3.6. SERVICE”. 3. Check mower deck for proper levelness. Refer CLUTCH/BRA
Résumé du contenu de la page N° 15
Section 3 - MAINTENANCE 3.3.4. TRACTOR LUBRICATION 9. Deck Lift Mechanism Lubricate all wear and pivot points of the deck lift. 6. Steering Drag Link Lubricate both ends of steering drag link with a small amount of 30 wt. motor oil from an oil can. See 3.4 ANNUALLY (END OF EACH SEASON) Figure 3.8. Perform all maintenance as described in Section “SERVICE - EVERY 25 OPERATING HOURS”. Also DRAG LINK see Service Schedule. LUBRICATION 3.4.1. ENGINE POINT 1. Service engine according to
Résumé du contenu de la page N° 16
Section 4 - ADJUSTMENT & REPAIR WARNING DO NOT attempt any adjustments, maintenance or service with the engine or blades running. STOP blades. STOP engine. Set brake. Remove key. ADJUSTING INSPECTION Remove spark plug wire from spark plug and secure NUT (3) SLOT (3) wire away from spark plug. Engine and components can be extremely hot. Avoid burns by allowing engine and components sufficient time to cool. 4.1 ENGINE ADJUSTMENTS & REPAIR Refer to the en
Résumé du contenu de la page N° 17
Section 4 – ADJUSTMENT & REPAIR SECTOR PLATES WARNING DO NOT attempt any adjustments, maintenance or service with the engine or blades running. STOP blades. STOP engine. Set brake. Remove key. Remove spark plug wire from spark plug and secure wire away from spark plug. Engine and components can be extremely hot. Avoid burns by allowing engine and components sufficient time to cool. 4.2.3. MOWER DECK ADJUSTMENT (LEVELNESS) LOWEST DECK 1. SIDE-To-SIDE (42” Decks) HIGHEST DECK
Résumé du contenu de la page N° 18
Section 4 - ADJUSTMENT & REPAIR 4.2.5. MOWER DECK ADJUSTMENT (LEVELNESS) TOP VIEW OF DECK SIDE-To-SIDE (48” Decks) Before making deck leveling adjustments, check the tire pressure. Check tires and add or release air as needed to bring pressure to 12 PSI in front and 12 PSI in rear tires. If tires are properly inflated and mowing is still uneven, adjust side-to-side deck levelness as follows: 1. Place machine on a smooth level surface. 2. Rotate outside blades so tips are pointed
Résumé du contenu de la page N° 19
Section 4 - ADJUSTMENT & REPAIR WARNING 4.2.6. MOWER DECK ADJUSTMENT (LEVELNESS) DO NOT attempt any adjustments, maintenance or (FRONT To REAR) service with the engine or blades running. STOP Before making deck leveling adjustments, check the tire pressure. Add or release air as needed to bring blades. STOP engine. Set brake. Remove key. pressure to 12 PSI in front and 12 PSI in rear tires. If Remove spark plug wire from spark plug and secure tires are properly inflated and mowing
Résumé du contenu de la page N° 20
Section 4 - ADJUSTMENT & REPAIR WARNING FUEL TANK DO NOT attempt any adjustments, maintenance or service with the engine or blades running. STOP blades. STOP engine. Set brake. Remove key. Remove spark plug wire from spark plug and secure wire away from spark plug. Engine and components can be extremely hot. Avoid burns by allowing engine and components sufficient time to cool. ROTATE TO 4.3 TRACTOR DRIVE COMPONENTS REDUCE “PLAY” ECCENTRIC 4.3.1. BRAKE ADJUSTMENT MOUNTING NUT
