Instruction d'utilisation Waring TAILGATER TG15

Résumé du contenu de la page N° 1

™
TAILGATER BLENDER
TG15
For your safety and continued enjoyment of this product,
always read the instruction book carefully before using.

Résumé du contenu de la page N° 2

CONTENTS Important Safeguards . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  Important Hot Blending Instructions . . . . . . . . . . . . . . . . . . 3 Operating Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 How To Assemble Containers with Removable Blades . . . 4 How To Disassemble and Clean Containers with Removable Blades. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 How To Clean Unit Base . . . . . . . . . . . . . . . . . . . . . . .

Résumé du contenu de la page N° 3

7. Do not let cord hang over edge of table or counter, or touch hot surfaces. 8. Keep hands and utensils out of jar while blending, to prevent the possibility of severe personal injury and/or damage to the blender. A rubber spatula may be used, but must be used only when the blender is not running. 9. Blades are very sharp. Handle carefully.  0. To avoid injury, never place blade assembly on the base unless container is properly attached.  . Always operate blender

Résumé du contenu de la page N° 4

IMPORTANT: HOT BLENDING INSTRUCTIONS To minimize possibility of being scalded when blending hot ingredients, the following precautions and procedures must be observed:  . Begin blending with no more than one cup (8 oz.) of ingredients. 2. Before turning blender on, remove the center lid insert. This will allow venting of the rapidly heated and expanding air. 3. Start blending on low speed. 4. While blender is running, up to  ½ cups ( 2 oz.) of additional liquid can

Résumé du contenu de la page N° 5

HOW TO ASSEMBLE CONTAINERS WITH REMOVABLE BLADES Always wash and rinse container prior to initial use.  . Before starting, make sure that the blender cord is unplugged and that the switch is in the Off position. 2. Refer to Figure  on page 5. The following points are important to note when putting together the container assembly: • Container gasket must be placed between blade assembly and container. • Collar must be threaded properly onto the blender container

Résumé du contenu de la page N° 6

HOW TO DISASSEMBLE AND CLEAN CONTAINERS WITH REMOVABLE BLADES Always wash and rinse container immediately after use.  . Be sure the switch is in the Off position. 2. Remove the container assembly from the unit base and empty the contents. 3. To disassemble the Waring ® ™ Pro Tailgater Blender, turn container collar clockwise. 4. The collar, blade assembly and gasket are dishwasher safe. The plastic container lid and insert must be washed by Fig.

Résumé du contenu de la page N° 7

HOW TO CLEAN UNIT BASE  . To clean the unit base, unplug the power cord. Wipe the exterior surfaces with a soft cloth or sponge dampened with cleaning solution. Rinse with clean water. Do not immerse the base in cleaning solution or water. Wipe the base with dry towel. FUSE REPLACEMENT The plug on the blender power cord contains a replaceable cartridge fuse. To gain access to the fuse, push the metal tip of the plug inward as far as it will go, then turn it counterclock

Résumé du contenu de la page N° 8

©2008 Waring Consumer Products Division of Conair Corporation Printed in USA  50 Milford Road TG 5 Tailgater IB East Windsor, NJ 08520 08WR204 www.waringproducts.com 028340