Résumé du contenu de la page N° 8
SYSTEM OK Alrm Test SYSTEM Uplink Alrm OK ETHERNET Alrm TX Test RX Uplink Alrm SYSTEM Coll OK ETHERNET Alrm TX Test RX Uplink Alrm Coll ETHERNET TX RX Coll SCM Card LEDs The following table describes the meaning and states of the LEDs on the Hotwire SCM card faceplate. Example faceplates are shown at left. Type LED LED is . . . Indicating . . . SYSTEM OK Green, Card functioning normally. Winking Winking describes a recurring pulse when the LED is ON longer than OFF at a ratio of approximatel
Résumé du contenu de la page N° 9
SCM Card Technical Specifications Table 3. SCM Card Technical Specifications (1 of 2) Specifications Criteria* Size Length: 10.4 inches (26.42 cm) Height: 11.15 inches (28.32 cm) Width: 1.0 inches (2.54 cm) Weight Approximately 1.4 lbs. (0.64 kg) Approvals Safety Certifications Refer to the equipment’s label for approvals on product. Power The SCM card contains a DC-to-DC converter that requires 48V power input. The 48V power is distributed through the Hotwire chassis backplane. Typical Power
Résumé du contenu de la page N° 10
Table 3. SCM Card Technical Specifications (2 of 2) Specifications Criteria* OC3 Uplink Specifications Number of ports 1 OC3 Connector Type Fiber SC connectors Standards Supported ANSI T1.105.06-94 Jitter, ANSI T1.105.09 94 Jitter, ANSI T1.117.06-91, ITU-T G.957 7/95 Frame Formats OC3 or STM-1 Operation, Direct Mode only Line Type Non-Return to Zero Data Rates Supported 155.52 Mbps Facility Datalink Protocol ANSI T1.105 Format, ANSI T1.646 HEC, ITU-T I.432 Scrambler Cable Distance Model 8022 (
Résumé du contenu de la page N° 11
Warranty, Sales, Service, and Training Information Contact your local sales representative, service representative, or distributor directly for any help needed. For additional information concerning warranty, sales, service, repair, installation, documentation, training, distributor locations, or Paradyne worldwide office locations, use one of the following methods: Internet: Visit the Paradyne World Wide Web site at www.paradyne.com. (Be sure to register your warranty at www.paradyne.com
Résumé du contenu de la page N° 1
®
Hotwire Shelf Concentration Module (SCM) Card
Installation Instructions
Document Number 8021-A2-GZ40-20
November 2000
What is a Hotwire Shelf Concentration Module?
®
A Hotwire Shelf Concentration Module (SCM) is a circuit card assembly (CCA)
that contains a parentcard with an ATM switch, a backplane interface, a processor,
a cell mux/demux, and an uplink childcard. The childcard determines the type of
ATM uplink supported by the SCM.
When the SCM card is used in a Hotwire 8820 GranDSLAM cha
Résumé du contenu de la page N° 2
Product Documentation Online Complete documentation for this product is available at www.paradyne.com. Select Library → Technical Manuals → Hotwire DSL & MVL Systems. Select the following documents: 8000-A2-GB22 Hotwire Management Communications Controller (MCC) Card, IP Conservative, User’s Guide 8000-A2-GB26 Hotwire MVL, ReachDSL/MVL, RADSL, IDSL, and SDSL Cards, Models 8310, 8312/8314, 8510/8373/8374, 8303/8304, 8353/8354, and 8343/8344, User’s Guide 8021-A2-GB20 Hotwire Shelf Concentrati
Résumé du contenu de la page N° 3
Installing the SCM Card Procedure To install the Hotwire SCM Card in Slot A of the GranDSLAM chassis: 1. If there is a filler plate covering the slot, remove it. 2. Remove the yellow screw covers. 3. Insert the card into the card guides of the slot on the chassis. 4. Carefully slide the card into the slot. Lift the insertion/ejection levers away from the faceplate until the card begins to engage the connectors on the backplane. Then press in on the insertion/ejection levers until the card is f
Résumé du contenu de la page N° 4
SYSTEM OK Alrm Test Uplink Alrm ETHERNET TX RX Coll IMA Uplink Card Connector Pinouts The IMA uplink has a RJ48M 50-pin Telco connector with 8 Tip/Ring and 8 Tip1/Ring1 connections that conforms to ANSI T1.403-1999. Paradyne offers an octopus cable for use with the IMA uplink (Feature No. 8026-F1-001 for Models 8026 and 8028, and Feature No. 8027-F1-001 for Model 8027). These cables contain a required ferrite to meet EMI requirements. If purchasing other Telco cables, you must attach the su
Résumé du contenu de la page N° 5
Table 1 lists connector pin assignments for Models 8026 and 8028. Table 2 lists connector pin assignments for Model 8027. Table 1. Feature No. 8026-F1-001 Connector Pin Assignments (1 of 2) DS1 or 120 Ohm RJ48M 50-Pin Telco RJ48C Connector E1 Port Connector Pinouts Pinouts Function Port 1 27 5 Data Out (Tip) 2 4 Data Out (Ring) 26 2 Data In (Tip) 1 1 Data In (Ring) Port 2 30 5 Data Out (Tip) 5 4 Data Out (Ring) 29 2 Data In (Tip) 4 1 Data In (Ring) Port 3 33 5 Data Out (Tip) 8 4 Data Out (Rin
Résumé du contenu de la page N° 6
Table 1. Feature No. 8026-F1-001 Connector Pin Assignments (2 of 2) DS1 or 120 Ohm RJ48M 50-Pin Telco RJ48C Connector E1 Port Connector Pinouts Pinouts Function Port 8 48 5 Data Out (Tip) 23 4 Data Out (Ring) 47 2 Data In (Tip) 22 1 Data In (Ring) Table 2. Feature No. 8027-F1-001 Connector Pin Assignments (1 of 2) RJ48M 50-Pin Telco 75 Ohm E1 Port Function Connector Pinouts BNC Connector Port 1 Data In 1 Shell (Ring) 26 Pin (Tip) Data Out 2 Shell (Ring) 27 Pin (Tip) Port 2 Data In 4 Shell (Rin
Résumé du contenu de la page N° 7
Table 2. Feature No. 8027-F1-001 Connector Pin Assignments (2 of 2) RJ48M 50-Pin Telco 75 Ohm E1 Port Function Connector Pinouts BNC Connector Port 6 Data In 16 Shell (Ring) 41 Pin (Tip) Data Out 17 Shell (Ring) 42 Pin (Tip) Port 7 Data In 19 Shell (Ring) 44 Pin (Tip) Data Out 20 Shell (Ring) 45 Pin (Tip) Port 8 Data In 22 Shell (Ring) 47 Pin (Tip) Data Out 23 Shell (Ring) 48 Pin (Tip) 8021-A2-GZ40-20 November 2000 7
