Résumé du contenu de la page N° 1
FCCID: GU67400-433
RF LINK OPERATING
Canadian Certification Number: 15021021494A
INSTRUCTIONS
This device complies with part 15 of the FCC rules. Operation is subject to the following two
conditions: 1) This device may not cause harmful interference, and 2) This device must accept any
interference received, including interference that may cause undesired operation. The Monarch® RF link 7400 radio frequency (RF) device provides a cable-
less solution to communications between the followin
Résumé du contenu de la page N° 2
Module/Unit Diagrams Following are diagrams of the available units with RF link modules attached. Renegade 4 Printer (also Rascal Printer available with an internal module) Sierra Sport 2 Printer (internal module only) 2 RF link Operating Instructions
Résumé du contenu de la page N° 3
If the printer and terminal are not communicating, try each of the following items: ♦ Change or recharge the batteries. ♦ Correct the orientation of the batteries in the compartment. ♦ Re-link the printer and terminal. ♦ Move the modules closer than three meters apart. ♦ Move the terminals and the printers around to find the best relative position between the two. LDT/LRT 3800 and PDT 6800 PDT 3100 ♦ Swap in new printers and terminals to narrow the problem down to a particular
Résumé du contenu de la page N° 4
2. Squeeze both sides of the module and snap it into the slots beneath the 3. Squeeze both sides of the module, and firmly pull the module straight terminal (below the keyboard). up. You will hear a loud snap when it comes apart from the terminal. NOTE: This step may be difficult the first few times you try it. PDT 3100 To remove the module from the PDT 3100: 1. Pull on the elastic hand strap and remove the latch from the slot. 2. Let go of the hand strap and gently pull the module off
Résumé du contenu de la page N° 5
NOTE: Internal RF link modules have their own communications port. If you 6. Insert the module onto the end of the terminal. are using an internal module, do not use the printer’s external port. Also, there are no problems using multiple printer/terminal pairs in the same area. Linking enables the two modules to talk only to each other during that link. Modules can be linked differently at other times. Powering RF link RF link runs on batteries, although in certain cases, the printer c
Résumé du contenu de la page N° 6
Printers Rascal Printers To install external RF link modules onto the printers: 1. Insert a 9-volt (PP3) battery in the module. See “Inserting Batteries” for more information. 2. Attach VELCRO to the serial port sides of the printer and the external module. Place the VELCRO so the cable on the module can reach the serial port. 3. Using the VELCRO, attach the module to the printer. Note that on the Renegade 4 printer, you must place the module so the cable faces down. On the Rasca
Résumé du contenu de la page N° 7
Renegade 4 Printers with External Modules Inserting Batteries To insert a battery into the external RF link module: 1. Carefully slide the battery door (located on the bottom of the terminal module and the non-VELCRO side of the printer module) to the right. You will hear a click. 2. Open the door to the left. It does not detach from the module. 3. Keeping the door pulled out, insert the battery in the compartment. Orient the battery so the top faces right, and the + contact (the small
Résumé du contenu de la page N° 8
Sierra Sport 2 Printers Renegade 4 Printers with Internal Modules To link a Renegade 4 printer (with an internal RF link module) to a data To link a Sierra Sport 2 printer to a data collection terminal: collection terminal: 1. Turn off the printer and the terminal’s RF link module. 1. Turn the printer, terminal, and the RF link modules off. 2. Turn on the printer. 2. Turn on the printer. The green LED on the side of the printer turns on. 3. Turn on the terminal’s RF link module. 3.
Résumé du contenu de la page N° 9
Sierra Sport 2 Printers Renegade 4 Printers with Internal Modules To link a Renegade 4 printer (with an internal RF link module) to a data To link a Sierra Sport 2 printer to a data collection terminal: collection terminal: 1. Turn off the printer and the terminal’s RF link module. 1. Turn the printer, terminal, and the RF link modules off. 2. Turn on the printer. 2. Turn on the printer. The green LED on the side of the printer turns on. 3. Turn on the terminal’s RF link module. 3.
Résumé du contenu de la page N° 10
Renegade 4 Printers with External Modules Inserting Batteries To insert a battery into the external RF link module: 1. Carefully slide the battery door (located on the bottom of the terminal module and the non-VELCRO side of the printer module) to the right. You will hear a click. 2. Open the door to the left. It does not detach from the module. 3. Keeping the door pulled out, insert the battery in the compartment. Orient the battery so the top faces right, and the + contact (the small
Résumé du contenu de la page N° 11
Printers Rascal Printers To install external RF link modules onto the printers: 1. Insert a 9-volt (PP3) battery in the module. See “Inserting Batteries” for more information. 2. Attach VELCRO to the serial port sides of the printer and the external module. Place the VELCRO so the cable on the module can reach the serial port. 3. Using the VELCRO, attach the module to the printer. Note that on the Renegade 4 printer, you must place the module so the cable faces down. On the Rasca
Résumé du contenu de la page N° 12
NOTE: Internal RF link modules have their own communications port. If you 6. Insert the module onto the end of the terminal. are using an internal module, do not use the printer’s external port. Also, there are no problems using multiple printer/terminal pairs in the same area. Linking enables the two modules to talk only to each other during that link. Modules can be linked differently at other times. Powering RF link RF link runs on batteries, although in certain cases, the printer c
Résumé du contenu de la page N° 13
2. Squeeze both sides of the module and snap it into the slots beneath the 3. Squeeze both sides of the module, and firmly pull the module straight terminal (below the keyboard). up. You will hear a loud snap when it comes apart from the terminal. NOTE: This step may be difficult the first few times you try it. PDT 3100 To remove the module from the PDT 3100: 1. Pull on the elastic hand strap and remove the latch from the slot. 2. Let go of the hand strap and gently pull the module off
Résumé du contenu de la page N° 14
If the printer and terminal are not communicating, try each of the following items: ♦ Change or recharge the batteries. ♦ Correct the orientation of the batteries in the compartment. ♦ Re-link the printer and terminal. ♦ Move the modules closer than three meters apart. ♦ Move the terminals and the printers around to find the best relative position between the two. LDT/LRT 3800 and PDT 6800 PDT 3100 ♦ Swap in new printers and terminals to narrow the problem down to a particular
Résumé du contenu de la page N° 15
Module/Unit Diagrams Following are diagrams of the available units with RF link modules attached. Renegade 4 Printer (also Rascal Printer available with an internal module) Sierra Sport 2 Printer (internal module only) 2 RF link Operating Instructions
Résumé du contenu de la page N° 16
FCCID: GU67400-433 RF LINK OPERATING Canadian Certification Number: 15021021494A INSTRUCTIONS This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: 1) This device may not cause harmful interference, and 2) This device must accept any interference received, including interference that may cause undesired operation. The Monarch® RF link 7400 radio frequency (RF) device provides a cable- less solution to communications between the followin
