Résumé du contenu de la page N° 1
Transition Networks
CPSMC0800-100
8-Slot PointSystem™ Chassis
User’s Guide
(revision A)
Résumé du contenu de la page N° 2
CPSMC0800-100 PointSystem™ Chassis Compliance Information UL Listed C-UL Listed (Canada) CISPR22/EN55022 Class A + EN55024 CE Mark FCC Regulations This equipment has been tested and found to comply with the limits for a class A digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equip- ment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency
Résumé du contenu de la page N° 3
CPSMC0800-100 PointSystem™ Chassis Table of Contents 1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 1.1 Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 1.2 Unpacking the CPSMC0800-100 Equipment . . . . . . . . . . . . . . . . .5 2 Slide-in-Modules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6 2.1 Media Converter Slide-in-Modules . . . . . . . . . . . . . . . . . . . . . . . .
Résumé du contenu de la page N° 4
introduction CPSMC0800-100 PointSystem™ Chassis 1 Introduction 1.1 Description The Transition Networks PointSystem™ CPSMC0800-100 is a 19-inch, rack-mount- able chassis for selected Transition Networks Media Converter Slide-In-Modules. The CPSMC0800-100 allows the network administrator to connect various copper and fiber-optic network media over protocols that include Ethernet™, Fast Ethernet™, DS3/E3, and OC-12. The CPSMC0800-100 provides installation space for up to eight (8) single-slot or
Résumé du contenu de la page N° 5
introduction CPSMC0800-100 PointSystem™ Chassis 2.1 Unpacking the CPSMC0800-100 Equipment Use the following list to verify the shipment: Item Part Number 8-Slot chassis with AC power supply CPSMC0800-100 8-Slot chassis with DC power supply CPSMC0810-100 Power Cord (varies by country) External AC Power Supply CPSMP-180 (optional) External DC Power Supply CPSMP-190 (optional) 1-slot Master Management Module CPSMM-100 (optional) 2-slot Master Management Module CPSMM-200 (optional) FocalPoint™ Sof
Résumé du contenu de la page N° 6
slide-in-modules CPSMC0800-100 PointSystem™ Chassis 2 Slide-in-Modules 2.1 Media Converter Slide-in-Modules Transition Networks Media Converter Slide-in-Modules, installed in slots at the front of the chassis, allow the network administrator to connect various copper and fiber- optic network media over protocols that include Ethernet, Fast Ethernet, DS3/E3, and OC-12 as well as many others (see www.transition.com for a complete listing.) NOTE: Refer to the documentation that comes with each Med
Résumé du contenu de la page N° 7
slide-in-modules CPSMC0800-100 PointSystem™ Chassis 2.1.2 Installing the Media Converter Slide-in-Modules CAUTION: Wear a grounding device and observe electrostatic discharge precau- tions when installing the Media Converter Slide-in-Module(s) into the chassis. Failure to observe this caution could result in damage to, and subsequent failure of, the Media Converter Slide-in-Module(s). NOTE: Media Converter Slide-in-Modules can be installed in any installation slot, in any order. To install th
Résumé du contenu de la page N° 8
slide-in-modules CPSMC0800-100 PointSystem™ Chassis 2.2.3 Replacing the Media Converter Slide-in-Modules CAUTION: Wear a grounding device and observe electrostatic discharge precau- tions when replacing Media Converter Slide-in-Module(s). Failure to observe this caution could result in damage to, and subsequent failure of, the Media Converter Slide-in-Module(s). NOTE: The Media Converter Slide-in-Modules are hot-swappable. To replace a Media Converter Slide-in-Module: 1. Remove the Media Conve
Résumé du contenu de la page N° 9
slide-in-modules DB-9 10BASE-T SERIAL TERM INIT 12C 12C-1 INPORT OUTPORT 10BASE-T CPSMC0800-100 PointSystem™ Chassis 2.2 Management Modules Optional network management is provided by SNMP software embedded in ™ Transition Networks PointSystem Management Module(s) that can be installed in the CPSMC0800-100 8-Slot chassis. Transition Networks provides two such modules: CPSMM-120 Single-Slot Master Management Module. CPSMM-200 Dual-Slot Master Management Module. Along with an additiona
Résumé du contenu de la page N° 10
slide-in-modules CPSMC0800-100 PointSystem™ Chassis 2.2.2 Installing the Managment Modules CAUTION: Wear a grounding device and observe electrostatic discharge precau- tions when installing the Management Module(s) in the 8-Slot chassis. Failure to observe this caution could result in damage to, and subsequent failure of, the Management Module. Install one (1) Master Management Module (CPSMM-120 or CPSMM-200) in the primary managed CPSMC0800-100 8-Slot chassis. If several PointSystem™chas
Résumé du contenu de la page N° 11
slide-in-modules CPSMC0800-100 PointSystem™ Chassis 2.2.3 Replacing the Mangement Modules CAUTION: Wear a grounding device and observe electrostatic discharge precau- tions when replacing Media Converter Slide-in-Module(s). Failure to observe this caution could result in damage to, and subsequent failure of, the Management Module(s). NOTE: The Managment Modules are NOT hot-swappable. To replace a Managment Module: 1. Remove the Managment Module to be replaced by loosening the one (1) screw tha
Résumé du contenu de la page N° 12
power supply CPSMC0800-100 PointSystem™ Chassis 3 Powering the CPSMC0800-100 The CPSMC0800-100 chassis can be powered through an AC or DC Power Supply. An optional auxilliary power supply, with Instant Fail Over protections, is also avail- able. NOTE: The CPSMC0800-100 8-Slot chassis does not have an ON/OFF switch. Power up the chassis by connecting the power supply. Power-down the chassis by disconnecting power supply. WARNING: THE AC AND DC POWER SUPPLIES CONTAIN NO USER-SERVICA- BLE
Résumé du contenu de la page N° 13
power supply CPSMC0800-100 PointSystem™ Chassis 3.2 Auxilliary Power Supply The CPSMC0800-100 can also be supplied with auxilliary power through the Auxilliary Power Inlet, located on the back panel. The External Power Converter and additional power cord are sold separately. To power the CPSMM0800-100 8-Slot chassis through the Auxilliary Power Supply: 1. Connect the female end of the External Power Converter to the Auxilliary Power Inlet on the back of the 8-Slot chassis. 2. Connect the f
Résumé du contenu de la page N° 14
chassis CPSMC0800-100 PointSystem™ Chassis 4 CPSMC0800-100 Chassis 4.1 Installing the CPSMC0800-100 Chassis The CPSMC0800-100 can be installed in a standard 19-inch rack or on a table, shelf, or other stable surface. 4.1.1 Standard 19-inch Rack Installation NOTE: The maximum recommended ambient temperature (Tmra) for the 8-Slot chassis is 40°C. If the 8-Slot chassis is installed in a closed or mult-unit rack assem- bly, the operating ambient temperature of the the rack environment may be great
Résumé du contenu de la page N° 15
chassis CPSMC0800-100 PointSystem™ Chassis To install the CPSMC0800-100 8-Slot chassis into a standard 19-inch rack: 1. Determine the preferred alignment of the 8-Slot chassis in the rack. NOTE: Installation bracket mounting screws are provided. Rackmount screws and clip nuts are NOT provided. 2. Locate six (6) installation bracket mounting screws (provided) for each chassis to be installed. WARNING: Mount the chassis evenly and securely onto the rack. Failure to observe this warning could allo
Résumé du contenu de la page N° 16
chassis CPSMC0800-100 PointSystem™ Chassis 4.2 Cascade Option The Management Module cascade option allows the network administrator to con- nect up to eight (8) CPSMC0800-100 8-Slot chassis into one manageable stack, pro- viding a single management source for up to 55 installed Media Converter devices. To create the cascade option, the CPSMM-200 Dual Slot Master Management Module is installed in the first chassis in the series. The CPSMM-210 Single-Slot Expansion Management Module is install
Résumé du contenu de la page N° 17
chassis CPSMC0800-100 PointSystem™ Chassis To cascade two or more CPSMC0800-100 8-Slot chassis: 1. Locate one (1) Transition Networks CPSMC0800-100 Management Module cas- cade cable (with RJ-45 connectors installed at both ends) for each set of two (2) chassis to be cascaded. NOTE: Transition Networks Management Module cascade cables are one (1) meter long. Ensure that the chassis are installed within one (1) meter of each other. 2. At the first chassis in the series: Plug the RJ-45 connector
Résumé du contenu de la page N° 18
chassis CPSMC0800-100 PointSystem™ Chassis 4.4 Operation Daily operation of the CPSMC0800-100 8-Slot chassis requires no network admin- istrator activity except for the occasional monitoring of the status LED indicators on the installed Media Converter Slide-In-Modules. Each Media Converter Slide-in-Module and each Management Slide-in-Module has one or more LED indicators to help monitor the CPSMC0800-100 PointSystem™ chassis network. Refer to the User’s Guide included with each Transition Ne
Résumé du contenu de la page N° 19
SNMP 10BASE-T SERIAL DB-9 TERM INIT 12C 12C-1 INPORT 10BASE-T OUTPORT CPSMC0800-100 PointSystem™ Chassis 5 SNMP Agent in the Management Module Both Management Modules (CPSMM-120 and (CPSMM-200) have an SNMP (Simple Network Managment Protocol) Agent installed in the module that allows remote managment of networked devices. The SNMP agent includes the Transition Networks PointSystem™ Command Line Interface (CLI) and an embedded Telnet server. These tools allow the network adminsitrator to con
Résumé du contenu de la page N° 20
SNMP CPSMC0800-100 PointSystem™ Chassis RJ-45 Ethernet™ Port The RJ-45 Ethernet™ Port allows the network administrator to manage the CPSMC1800-100 8-Slot chassis via a remote Network Management Station (NMS) in one of two ways: 1. Using the Transition Networks FocalPoint™ graphical user interface. 2. Using a remote Telnet connection. Use an RJ-45 network cable to attach a terminal (via a network hub or switch) to the RJ-45 Ethernet™port on the Management Module as shown. DB-9 Mpls, MN 55344 Mp
