Résumé du contenu de la page N° 1
December 2009
LR0201A-KIT
G.SHDSL Two-Wire Ethernet Network Extender
Extend Ethernet with full-duplex transmission
®
BL A CK BOX
up to 5.696 Mbps—more than four miles—over
a pair of copper wires.
Complies with ITU-T Rec. G.991.2 G.shdsl.bis standards.
Supports adaptive data rates from 4.608 Mbps to 192 kbps for SHDSL line.
Works at distances up to 22,500 feet over 26 AWG twisted-pair cable.
Has two RJ-45 connectors for 10BASE-T/100BASE-TX Ethernet ports
for combining two separate Ether
Résumé du contenu de la page N° 2
G.SHDSL Two-Wire Ethernet Network Extender Trademarks Used in this Manual Black Box and the Double Diamond logo are registered trademarks of BB Technologies, Inc. Any other trademarks mentioned in this manual are acknowledged to be the property of the trademark owners. We‘re here to help! If you have any questions about your application or our products, contact Black Box Tech Support at 724-746-5500 or go to blackbox.com and click on “Talk to Black Box.” You’ll be live with one of our techni
Résumé du contenu de la page N° 3
FCC and IC RFI Statements Federal Communications Commission and Industry Canada Radio Frequency Interference Statements This equipment generates, uses, and can radiate radio-frequency energy, and if not installed and used properly, that is, in strict accordance with the manufacturer’s instructions, may cause interf erence to radio communication. It has been tested and found to comply with the limits for a Class A computing device in accordance with the specifications in Subpart J of Part 15 o
Résumé du contenu de la page N° 4
G.SHDSL Two-Wire Ethernet Network Extender Normas Oficiales Mexicanas (NOM) Electrical Safety Statement INSTRUCCIONES DE SEGURIDAD 1. Todas las instrucciones de seguridad y operación deberán ser leídas antes de que el aparato eléctrico sea operado. 2. Las instrucciones de seguridad y operación deberán ser guardadas para referencia futura. 3. Todas las advertencias en el aparato eléctrico y en sus instrucciones de operación deben ser respetadas. 4. Todas las instrucciones de operación y uso d
Résumé du contenu de la page N° 5
CE Statement European Community (CE) Electromagnetic Compatibility Directive This equipment has been tested and found to comply with the protection requirements of European Emission Standard EN55022/EN61000-3 and the Generic European Immunity Standard EN55024. EMC: EN55022(2003)/CISPR-2( 2002): Class A IEC61000-4-2 (2001): 4 KV CD, 8 KV AD IEC61000-4-3( 2002): 3V/m IEC61000-4-4(2001): 1 KV (power line), 0.5 KV (signal line) 724-746-5500 | blackbox.com Page 5
Résumé du contenu de la page N° 6
G.SHDSL Two-Wire Ethernet Network Extender 1. Specifications ........................................................................................................................................................................................ 7 2. Overview ............................................................................................................................................................................................... 8 2.1 Introduction ......................
Résumé du contenu de la page N° 7
Chapter 1: Specifications 1. Specifications Data Rate: 64 kbps–5.696 Mbps Distance: On 26 AWG twisted pair: 5696 kbps: 4500 feet (0.9 miles), 4608 kbps: 5500 feet (1 miles), 3088 kbps: 9500 feet (1.8 miles), 2304 kbps: 12,000 feet (2.3 miles), 2048 kbps: 13,000 feet (2.5 miles), 1544 kbps: 13,300 feet (2.5 miles), 1536 kbps: 13,500 feet (2.6 miles), 1152 kbps: 15,000 feet (2.8 miles), 768 kbps: 17,000 feet (3.2 miles), 512 kbps: 18,000 feet (3.4 miles), 384 kbps: >18,000 feet
Résumé du contenu de la page N° 8
G.SHDSL Two-Wire Ethernet Network Extender 2. Overview 2.1 Introduction The LR0201A-KIT, a G.SHDSL (Single-pair High-bit-rate Digital Subscriber Line) Two-Wire Ethernet Network Extender, provides broadband full-duplex transmission with bandwidth up to 5.696 Mbps over a pair of copper twisted-pair lines for point-to-point LAN connectivity between two Ethernet networks. The LR0201A-KIT is a cost-effective symmetrical broadband solution for band- width-hungry applications such as LAN-to-LAN conne
Résumé du contenu de la page N° 9
Chapter 2: Overview 2.3. Application LR0201A-KIT LR0201A-KIT (CO Site—Master) (Remote SIte—Slave) Ethernet Switch Ethernet Switch LAN LAN SHDSL Cooper Line (5.696 Mbps at 7000 ft.) Internet Figure 2-1. Typical application. 2.4 What’s Included Your package should include the following items. If anything is missing or damaged, please contact Black Box Technical Support at 724-746-5500. • ( 2) G. S HD S L T w o -Wi r e E t he rne t Ne t w or k Ex t e n de rs • ( 2 ) P o w e r
Résumé du contenu de la page N° 10
G.SHDSL Two-Wire Ethernet Network Extender 2.6 Front and Back Panels LED Indicators RS-232 Console Port Figure 2-2. Front panel. Power Input RJ-45 Connectors RJ-48 Connector Power Switch Figure 2-3. Rear panel. Page 10 724-746-5500 | blackbox.com
Résumé du contenu de la page N° 11
Chapter 3: Installation 3. Installation 1. Connect the SHDSL line to the DSL RJ-48 connector on the LR0201A-KIT’s rear panel. Pin 4 and Pin 5 for SHDSL line Figure 3-1. RJ-48 connector, Pins 4 and 5. 2. Connect the Ethernet interface to the RJ-45 port with the included CAT5 cable. 3. Connect the included power cord to the AC outlet. CAUTION: Verify that the AC–DC adapter conforms to your country’s AC power requirement and then insert the power plug. NOTE: The Interconnecting cables sh
Résumé du contenu de la page N° 12
G.SHDSL Two-Wire Ethernet Network Extender 4. Console Configuration The LR0201A-KIT has an RS-232C console port so users can monitor the OA&M status through a VT100 terminal. This section covers the operating procedures and settings for all screen selections. Connect the RS-232 cable to the COM port of the computer as shown in Figure 4-1. Set the personal computer to VT100 or VT102 type through HyperTerminal. Press the key and the main menu will be shown on the screen of the terminal
Résumé du contenu de la page N° 13
Chapter 4: Console Configuration 4.1. Main Menu The Main Menu screen enables you to access the LR0201A-KIT’s Configuration or Status screens. For details, refer to Figure 4-2. Welcome to G. Shdsl Ethernet Network Extender User Interface Main Menu 1. Configuration 2. Status Select (1-2) [ENTER] select Figure 4-2. Main menu. The main menu’s pull-down tree structure is shown in Figure 4-3. DSL Mode DSL Speed Configuration Default Configuration Main Menu System Information Status System Status
Résumé du contenu de la page N° 14
G.SHDSL Two-Wire Ethernet Network Extender 4.2. Configuration Screen The Configuration screen will display the LR0201A-KIT unit’s selection. On this screen, you can choose from three settings selections: DSL Mode, DSL Speed, and Default Configuration. Configuration 1. DSL Mode 2. DSL Speed 3. Default Configuration Select (1-3): [ENTER] select Figure 4-4. Configuration screen. 4.2.1. DSL Mode Screen From the DSL Mode screen, users can update DSL mode settings. The DSL Mode settings’ initia
Résumé du contenu de la page N° 15
Chapter 4: Console Configuration CO/RT: CO/RT has 2 options: STU-C and STU-R. To establish a successful connection for two G.SHDSL Two-Wire Ethernet Network Extenders, set one unit to STU-C (CO Site) and the other unit to STU-R (Remote Site). 2P/1P: 2P/1P has 2 options: 1 Pair and 2 Pairs. The LR0201A-KIT only supports a 1-pair SHDSL application. To establish a successful con- nection for LR0201A-KIT, set the two units to the same selection. 4.2.2 DSL Speed Screen From the DSL Speed screen, use
Résumé du contenu de la page N° 16
G.SHDSL Two-Wire Ethernet Network Extender 4.2.3. Default Configuration Screen When Default Configuration is selected, all the settings of the LR0201A-KIT will go back to default settings. The screen shown in Figure 4-7 indicates that the setting is finished. Press key to return to the previous screen. The LR0201A-KIT’s default settings are: STU-C 1 Pair Adaptive speed Now the settings are STU-C, 1 Pair, and Adaptive Speed. Press [ESC] to quit [ENTER] quit Figure 4-7. Default Configur
Résumé du contenu de la page N° 17
Chapter 4: Console Configuration 4.3 Status Screen The Status screen shows the LR0201A-KIT’s connection status. The screen covers two selections: System Information and System Status. Status 1. System Information 2. System Status Select (1-2): [ENTER] select [ESC] quit Figure 4-8. Status screen. 4.3.1 System Information Screen Firmware Version: Indicates the firmware version in this unit. Vendor Model: Indicates this device’s vendor model name. Vendor Information: Indicates the vendor’
Résumé du contenu de la page N° 18
G.SHDSL Two-Wire Ethernet Network Extender 4.3.2 System Status Screen DSL mode: Indicates the current DSL mode setting. Speed setting: Indicates the current DSL speed setting. Speed actual (kbps): Indicates the actual DSL speed in kilobits per second. Link status of Pair #1: Indicates the DSL connection status (either up or down) for Pair #1. Link status of Pair #2: Indicates the DSL connection status (either up or down) for Pair #2. Noise margin of Pair #1 (dB): Indicates the Noise Margin
Résumé du contenu de la page N° 19
Black Box Tech Support: FREE! Live. 24/7. Tech support the way it should be. Great tech support is just 20 seconds away at 724-746-5500 or blackbox.com. About Black Box Black Box Network Services is your source for more than 118,000 networking and infrastructure products. You’ll find everything from cabinets and racks and power and surge protection products to media converters and Ethernet switches all supported by free, live 24/7 Tech support available in 20 seconds or less. © Copyright
