Résumé du contenu de la page N° 1
ADSL Wireless Modem Router
With 4-port Switch
ADW-4100
User’s Manual
Résumé du contenu de la page N° 2
Copyright Copyright (C) 2003 PLANET Technology Corp. All rights reserved. The products and programs described in this User ’s Manual are licensed products of PLANET Technology, This User’s Manual contains proprietary information protected by copyright, and this User’s Manual and all accompanying hardware, software, and documen- tation are copyrighted. No part of this User’s Manual may be copied, photocopied, reproduced, translated, or reduced to any electronic medium or machine-readabl
Résumé du contenu de la page N° 3
Trademarks The PLANET logo is a trademark of PLANET Technology. This documentation may refer to numerous hardware and software products by their trade names. In most, if not all cases, these designations are claimed as trademarks or registered trademarks by their respective companies. Revision User’s Manual for PLANET ADSL Wireless Modem Router: Model: ADW-4100A/ADW-4100B Rev: 1.0 (August 2003) Part No.: EM-ADW4100 iii
Résumé du contenu de la page N° 4
TABLE OF CONTENTS CHAPTER 1 INTRODUCTION .................................................................................1 ADW-4100 Features ..........................................................................................1 Internet Access Features .............................................................................1 Advanced Functions.....................................................................................1 LAN Features......................................
Résumé du contenu de la page N° 5
Learned MAC Table .........................................................................................41 ADSL Configuration..........................................................................................42 RIP Configuration.............................................................................................42 Password Configuration ...................................................................................44 Misc Configuration.................................
Résumé du contenu de la page N° 6
Chapter 1 Introduction 1 This Chapter provides an overview of ADW-4100's features and ca- pabilities. Congratulations on the purchase of ADW-4100. The ADSL Wireless Modem Router will allow multiple LAN and WLAN users to share an Internet user account, via a DSL connection. Once the ADSL Wireless Modem Router is installed and configured, the Internet is just a click away. Figure 1-1: ADSL Bridge Router ADW-4100 Features ADW-4100 incorporates many advanced features, carefully designe
Résumé du contenu de la page N° 7
ADW-4100 User Manual w DMZ. One (1) PC on your local LAN can be configured to allow unrestricted 2-way communication with Servers or individual users on the Internet. This provides the ability to run programs which demand for bi-directional communi- cation. LAN Features w Built-in 4-port switch. Four Auto-Negotiation, Auto-MDI/MDI-X Ethernet RJ-45 ports are used to connect office network or workstations. w 802.11b WLAN support. ADW-4100 is a Wi-Fi compliant Access Point, provides operati
Résumé du contenu de la page N° 8
Introduction Physical Details Front Panel WAN LAN ADSL Wireless Modem Router 3 1 ADSL PWR ADW-4100 4 2 ACT WLAN Figure 1-2: Front Panel LED definitions LEDs Color Active Description The power adaptor is connected to the Mo- PWR Green ON dem. WLAN Green ON The wireless link is established. ADSL Green ON ADSL connection is established. WAN ACT Green ON Transmit data or receive data via ADSL link. 1 2 Transmit data or receive data over Ethernet LAN Green ON link. 3 4 Rear
Résumé du contenu de la page N° 9
ADW-4100 User Manual Restore Default IP Address and Clear Password If ADW-4100's IP Address or password is lost, the following procedure can be used to recover from this situation. Pressing the Reset button for more than 10 seconds. ADW-4100 will restore to factory default setting. Note that this should be done only when you had tried all the troubleshooting options. Pressing the Reset button during operation may bring you into the risk of creating IP address conflict between your PC and
Résumé du contenu de la page N° 10
Chapter 2 Installation 2 This Chapter covers the physical installation of ADW-4100. System Requirements • PC or TCP/IP compliant workstations • 32 MB RAM • Ethernet Network Interface Controller (NIC) RJ45 Port • Internet Browser Installation Procedure Figure 2-1: Installation Diagram Step 1 Choose an Installation Site Select a suitable place on the network to install ADW-4100. Ensure ADW-4100 is powered OFF. Step 2 Connect LAN Cables Use standard LAN cables to connect PCs
Résumé du contenu de la page N° 11
ADW-4100 User Manual Connect the supplied power adapter to ADW-4100 and power up. Use only the power adapter provided. Using a different one may cause hardware damage. Step 5 Check the LEDs For each LAN (PC) connection, the corresponding LAN LED should be ON (pro- vided the PC is also ON.). The WLAN and ADSL LED should be ON. 6
Résumé du contenu de la page N° 12
Login And System Status Chapter 3 Login And System Status 3 This Chapter details the first time login procedure and the Status screen Login ADW-4100 contains an HTTP server. This enables you to connect to it, and config- ure it, using your Web Browser. Your Browser must have JavaScript support. The configuration program has been tested on the following browsers: • Netscape V4.08 or later • Internet Explorer V4 or later Moreover, it is suggested to use an Ethernet LAN PC for the initial
Résumé du contenu de la page N° 13
ADW-4100 User Manual Figure 3-1: Logon Window If you can't connect If ADW does not respond, check the following: • Machine is properly installed, LAN connection is OK, and it is powered ON. You can test the connection by using the "Ping" command: • Open the MS-DOS window or command prompt window. • Enter the command: ping 10.0.0.2 If no response is received, either the connection is not working, or your PC's IP address is not compatible with ADW-4100's IP Ad- dress. (See next it
Résumé du contenu de la page N° 14
Login And System Status Status Home Once you login in ADW-4100, its Home page will appear. It shows the firmware versions and WAN and LAN interface status. Figure 3-2: Home page ADSL The ADSL Status page shows the ADSL physical layer status. Figure 3-3: ADSL status 9
Résumé du contenu de la page N° 15
ADW-4100 User Manual LAN The LAN page shows the information and status of LAN port, DHCP client table, and linking status of Ethernet interface. Figure 3-4: LAN status PPP The PPP page shows the status of PPP for each PPP interface. Figure 3-5: PPP status 10
Résumé du contenu de la page N° 16
Chapter 4 System Configuration 4 This Chapter details the configurations for ADW-4100 Overview This chapter describes the setup procedure for: • WAN Access • LAN configuration PCs on your local LAN may also require configuration. For details, see Chapter 5 - PC Configuration. WAN configuration Select the WAN link under Configuration column to set up WAN connection. It is required to know the type of Internet connection service used by your ISP. Note: You only need to fill in t
Résumé du contenu de la page N° 17
ADW-4100 User Manual Figure 4-2: Per VC Settings To switch between the PVCs, please choose the options of virtual circuit and click on the Submit button to switch over. Figure 4-3: Switch between PVCs Internet connection services Types of Internet connection services supported by ADW-4100 are explained below. Bridge Mode Step 1 At the WAN Configuration page, insert the VCI/VPI provided by ISP. Enable “Bridge”, and choose suitable packet encapsulation. Figure 4-4: Bridge s
Résumé du contenu de la page N° 18
System Configuration Figure 4-5: Encapsulation types of Bridge mode Step 2 Click “submit” to commit modifications you’ve done, then click “Save Configura- tion” to store settings. (Modifications will not take effects until next reboot.) Step 3 Click on “NAT” tab on left panel, and disable the NAT function in the option menu. Figure 4-6: NAT Disable screen Step 4 Click “Save settings” on left panel to write configuration into machine, and reboot to make settings effective. P
Résumé du contenu de la page N° 19
ADW-4100 User Manual be obtained from ISP. And VCI/VPI values must be obtained from them as well, for some local ISPs don’t offer this information actively. To set up a PPPoE or PPPoA connection for WAN, follow the instructions below: Step 1 Fill in the VCI/VPI entries with the information you get from ISP. Step 2 Choose suitable packet encapsulation (PPPoA LLC/VC-Mux, PPPoE LLC/VC-Mux). Disable “Bridge”. (Packet encapsulation information also has to be obtained from ISP.) Figure 4-
Résumé du contenu de la page N° 20
System Configuration connection handshake. The default value is 1432. Authentication When AUTO option is chosen, the PAP mode will run first then CHAP. Automatic Reconnect If you check this option, the Disconnect Timeout should set to 0 second. Otherwise there will be a conflict between them. DHCP Leave this option unchecked. Figure 4-8: PPP setting Screen Step 3
