Instruction d'utilisation Axor Interaktiv & Retroaktiv 4-Hole Roman Tub Trim Stratos 06667XX0

Résumé du contenu de la page N° 1

Installation Instructions / Warranty
Interaktiv
Retroaktiv
4-Hole Roman Tub Trim

Résumé du contenu de la page N° 2

Interaktiv & Retroaktiv 4-Hole Roman Tub Trim These instructions cover the following trim kits: Interaktiv Solaris 06665XX0 Stratos 06667XX0 Metro 06669XX0 Interaktiv S 06876XX0 Retroaktiv Swing Tango Limbo Cross handle 06125XX0 06048XX0 06113XX0 Scroll handle 06124XX0 06047XX0 06112XX0 Lever handle 06123XX0 06046XX0 06110XX0 Proaktiv* 06322XX0 06319XX0 06312XX0 *handles not included, sold separately Installation considerations 4-hole roman tub rough valve 06646000 must be instal

Résumé du contenu de la page N° 3

Retroaktiv Swing - Cross handles shown Tango - Swing handles shown Limbo - Lever handles shown 3

Résumé du contenu de la page N° 4

Install the Handles Remove the plaster shields from the hot and cold valves. Retroaktiv only: Install the deco rings on the handles. All models: Position the handle over the valve stem with the lever in the desired “off” position. Holding the lever in place with one hand, use your other hand to turn the “bell” and screw it down over the valve. Assemble the Diverter and Spout Remove the plaster shield from the spout tee. Remove the brass plug from the tee. 4

Résumé du contenu de la page N° 5

Interaktiv and Swing Screw the nut onto the diverter. Screw the shorter threaded end of the threaded rod into the nut. Slide the rod trim onto the rod and screw into place so that a few threads protrude from the top. Firmly press the diverter assembly straight into the spout tee until it is fully seated. Swing only: install the spout deco ring on the spout. Make sure that the set screw hole in the deco ring lines up with the set screw hole in the spout. Press the spout over the tee and

Résumé du contenu de la page N° 6

Limbo Screw the socket onto the diverter. Insert the ball rod into the socket. Press the white plastic retainer clip over the ball rod. Press into place over the socket. Press the diverter assembly firmly into the spout tee until it is fully seated. Firmly press the spout over the tee and diverter. Tighten the set screw with the included 3 mm Allen wrench. CAUTION: do not overtighten the set screw or the o-rings on the diverter will deform, which will cause a leak. Use the included wren

Résumé du contenu de la page N° 7

Firmly press the spout over the tee and diverter. Tighten the set screw with the included 3 mm Allen wrench. CAUTION: do not overtighten the set screw or the o-rings on the diverter will deform, which will cause a leak. Install the pull rod. The threaded end of the pull rod must go into the hole in the pin. Install the Handshower Holder Escutcheon and Handshower Remove the plaster shield from the handshower holder. Pull out on the handshower hose. Screw the handshower holder escutch

Résumé du contenu de la page N° 8

Replacement Parts Retroaktiv 8 10 4e 9 9 1 1 4f 5 5 4g Swing Tango Limbo 6 4h 9 3 1 4i 7 5 2 4j 8

Résumé du contenu de la page N° 9

8 6 4b 9 1 3 4c 7 2 4a 4d Interaktiv 1 aerator 13956XX0 2 handshower holder escutcheon 97159XX0 3 elbow 28071XX0 4 handle set 4a Solaris 06850XXX 4b Stratos 06852XXX 4c Metro 06853XXX 4d Interaktiv S 06957XXX 4e High cross 06326XXX 4f High scroll 06325XXX 4g High lever 06324XXX 4h Low cross 06305XXX 4i Low scroll 06034XXX 4j Low lever 06303XXX 5 Retroaktiv handle deco ring 88600XX0 6 handshower - Raindance AIR 1-Jet handshower - Retroaktiv 06127XX0 7 check valve

Résumé du contenu de la page N° 10

Scale Removal The Raindance Air 1-jet handshower incorporates the TM Rubit cleaning system. If scale deposits are noticed in the spray channels, turn the water on lightly and rub the spray channels with a finger or a sponge. If scale deposits are noticed on the spray face, pour about 3/4” of a commercial scale remover, such as TM TM Lime-Away or CLR ,into a shallow dish. Dilute the remover according to the label instructions. Soak only the spray face in the solution for the amount of tim

Résumé du contenu de la page N° 11

Cleaning Recommendation for Hansgrohe Products Modern faucetry and shower products utilize a combination of materials to comply with the needs of the market with regard to design and functionality. To avoid damage, it is necessary to use some caution when cleaning. Damage caused by improper treatment is not covered under the Hansgrohe warranty. Cleaning Materials for Faucets and Showers • To remove lime scale, use only products made specifically for that purpose. Always follow the manufactur

Résumé du contenu de la page N° 12

C. Labor or other expenses for the disconnection or return of the product for warranty service, or for installation or reinstallation of the product. D. Accessories or related products not manufactured by Hansgrohe. TO OBTAIN WARRANTY SERVICE Contact your Hansgrohe retailer, or write to Technical Service at: Hansgrohe Inc. 1492 Bluegrass Lakes Parkway Alpharetta GA 30004 Or, call Hansgrohe toll-free at (800) 334-0455. In requesting warranty service, you will need to provide 1. The sales receip