Instruction d'utilisation Dymo Electronic Date/Time Stamper

Résumé du contenu de la page N° 1

IMPORTANT!
Please read ALL instructions carefully
before operating.
Your DYMO Electronic Date/Time Stamper will
save you time and increase your productivity.
Here are just some of its advanced features:
• Automatically prints Date and/or Time.
• Prints 7 preprogrammed messages and
4 or 6 digit auto-numbering.
• LCD displays message, date, and time.
Electronic
Date/Time Stamper
DYMO
Tel: 800.426.7827 or 203.355.9000
Fax: 203.355.9090
User Guide
www.dymo.com
DYMO, AN ESSELTE BRAND
©2000 DYMO Co

Résumé du contenu de la page N° 2

Usage Tips To maintain your stamper at peak operating performance, please follow these guidelines: Table of Contents 1. Do not touch the printer head or belt when Getting Started 6 the unit is printing. This will cause the printer Setting Date & Time 7 to malfunction and require servicing. Stamping/Printing Options 8 2. Immediately replace LCD display cell-battery Selecting which fields to print 9 if the BATT indicator lights up on the LCD. Auto-numbering 10 3. If printer speed slows down, repla

Résumé du contenu de la page N° 3

R R E MADE IN CHINA E T Getting Started shuttle to return to the start position. 4. The unit is now ready for use. 1. Open the If the unit does not reset, verify that the print belt battery compartment shuttle(bottom of unit) is not jammed and slides as shown. freely across belt (use ball point pen). Repeat (figure 2) steps 1-4 above. Low Cell Battery Detection figure 2 Your DYMO Electronic Date/Time Stamper 2. To activate printing automatically checks itself every hour to detect a low functions

Résumé du contenu de la page N° 4

R R R R E E E E T T or a paper clip to figure 4 rotate the ink roll 4. Snap the battery door back counter-clockwise and into place. pull it out of the unit. 5. Remove and discard the (see Figure 6) "AA" UM-3 1.5V OPEN clear protective cover from figure 6 3.0 VOLT 3. Apply a few drops "AA" UM-3 1.5V the bottom of the unit. of ink-pad ink onto the Setting Date and Time roll, then carefully insert the roll back into proper position inside the unit. Or simply 1. To set the current date and time

Résumé du contenu de la page N° 5

NOTE: If you go past the current year, you will 1. Press and hold the Security Code button for need to press the LOCK button to cycle 2 seconds. up to through the year 2189, and back the current year. 2. Press LOCK to set the first digit of the code, then SHIFT to move on to the next digit. Repeat this step until all digits of the code 4. Once you are finished setting the Date and are entered. Time press the SET/EDIT button to return to 3. Press SECURITY CODE to return to normal normal displa

Résumé du contenu de la page N° 6

normal display. pattern press the ALARM MODE button to finish print programming and return to normal display. How to lock Auto-numbering Auto-numbering To prevent the counter from automatically advancing to the next sequential number after Your Date/Time Stamper allows you to use either each printing, press the LOCK button. The 4 or 6 digit auto numbering Follow the CNTLOCK indicator will appear on the LCD. To instructions below for setup: deactivate, press the LOCK button again and the CNTLOCK

Résumé du contenu de la page N° 7

Selecting which fields to print Stamper will emit a series of short 1. Press the PRINT SELECT button for 2 beeps. To shut off the alarm, press seconds, the DATE field will start flashing ALARM MODE. 2. By pressing the SET/EDIT button you can turn the rectangle surrounding the DATE field Deactivating the alarm on or off. If you wish to print the date, make sure the rectangle is on. 1. Press ALARM MODE, then press LOCK so the "bell" icon will disappear. 3. To move on to the next field press the 2

Résumé du contenu de la page N° 8

In program mode, allows you to change the value of all available fields. LOCK Date/Time Stamper SHIFT DATE TIME MESSAGE FILE Press to change message ALARM SECURITY SET/ PRINT to be printed. In program MODE CODE EDIT SELECT mode, allows you to navigate between the available fields. Press to select message to be printed. www.dymo.com Allows you to set security code. Press to Allows you display time to enter alarm will program mode. sound.