Instruction d'utilisation Epson Stylus Pro SP4000

Résumé du contenu de la page N° 1

CPD17011R1_Isa_SH_E.qxd 9/21/04 5:13 PM Page 1
®
EPSON Stylus Pro 4000
Load Roll Paper
Start Here
Start Here
1 Slide the black paper stop off the end of
the spindle.
Unpack
2 If the paper has a 2-inch core, remove the adapters
1 Make sure you have all the parts shown below for your EPSON Stylus Pro 4000: by pressing the four tabs.
Note: Make sure your hands are clean, and avoid touching the printable surface of the paper.
Try to handle paper by the edges. Make sure you don’t rub or scratch

Résumé du contenu de la page N° 2

CPD17011R1_Isa_SH_E.qxd 9/21/04 5:13 PM Page 1 ® EPSON Stylus Pro 4000 Install Ink Load Roll Paper Start Here Start Here Use the ink cartridges that came with your printer for initial ink charging. During the initial 1 Slide the black paper stop off the end of installation process, it is normal for up to one-third of the ink in each cartridge to be used. the spindle. Unpack 1 Press the Power button to turn on the printer. 2 If the paper has a 2-inch core, remove the adapters 1 Make sure you

Résumé du contenu de la page N° 3

Load Roll Paper 1 Slide the black paper stop off the end of the spindle. 2 If the paper has a 2-inch core, remove the adapters by pressing the four tabs. Note: Make sure your hands are clean, and avoid touching the printable surface of the paper. Try to handle paper by the edges. Make sure you don’t rub or scratch the coating or dent the edges of the paper. 3 Position the roll so the paper unwinds as shown, then slide it onto the spindle. 4 Slide the black paper stop back onto the spindle. Inse

Résumé du contenu de la page N° 4

CPD17011R1_Isa_SH_E.qxd 9/21/04 5:13 PM Page 2 Load Cut Sheet Paper When you are ready to print on cut sheet paper, make sure you release the paper lever and wind up the roll paper. Then return the paper lever to the secured position and close the roll paper cover. Note: Some papers cannot be used with the paper tray. You need to load them through the front or top manual feed slots. See the Printer Guide for details. 1 Make sure the printer is on and ready to print. 2 Pull out the paper tray

Résumé du contenu de la page N° 5

CPD17011R1_Isa_SH_E.qxd 9/21/04 5:13 PM Page 2 Connect to Your System You can use either of the following connections. Make sure your system has the appropriate port, and you have a standard, shielded cable 10 feet long or less: USB cable ® IEEE FireWire cable If you have the optional EpsonNet Ethernet card, you can connect the printer directly to your network. You’ll need a standard RJ-45 network cable. 1 Make sure that both the printer and the computer are off. 2 Plug the interface cable in

Résumé du contenu de la page N° 6

CPD17011R1_Isa_SH_E.qxd 9/21/04 5:13 PM Page 2 10 Pull down the menu and select the connection you are using—either EPSON USB, EPSON FireWire, or EPSON TCP/IP. The Stylus Pro 4000 appears on the Printer List screen. 11 Click Stylus Pro 4000, then open the Page Setup pull-down menu. 12 Select All, then click Add. Windows 1 Make sure your printer is turned off. 2 Turn on your computer. 3 Insert the printer software CD-ROM in your computer. The installer starts automatically. If it doesn’t sta