Résumé du contenu de la page N° 1
Projector
CP-X8150/CP-X8160/
CP-WX8240/CP-WX8255/
CP-SX8350/CP-WU8440/CP-WU8450
User's Manual (detailed)
Operating Guide – Technical
Example of computer signal
Resolution (H x V) H. frequency (kHz) V. frequency (Hz) Rating Signal mode
720 x 400 37.9 85.0 VESA TEXT
640 x 480 31.5 59.9 VESA VGA (60Hz)
640 x 480 37.9 72.8 VESA VGA (72Hz)
640 x 480 37.5 75.0 VESA VGA (75Hz)
640 x 480 43.3 85.0 VESA VGA (85Hz)
800 x 600 35.2 56.3 VESA SVGA (56Hz)
800 x 600 37.9 60.3 VESA SVGA (60Hz)
800 x 600 48.1
Résumé du contenu de la page N° 2
Example of computer signal Resolution (H x V) H. frequency (kHz) V. frequency (Hz) Rating Signal mode *1 1280 x 1024 91.1 85.0 VESA SXGA (85Hz) *2 1400 x 1050 65.2 60.0 VESA SXGA+ (60Hz) *3 1680 x 1050 65.3 60.0 VESA WSXGA+ (60Hz) *1 1600 x 1200 75.0 60.0 VESA UXGA (60Hz) W-UXGA (60Hz) *4 1920 x 1200 74.0 60.0 VESA Reduced Blanking TM *1) Supported except for HDMI input. *2) Only for CP-X8150, CP-X8160 and CP-SX8350. *3) Only for CP-WX8240, CP-WX8255, CP-WU8440 and CP-WU8450. TM *4) Only for CP
Résumé du contenu de la page N° 3
Initial set signals Initial set signals The following signals are used for the initial settings. The signal timing of some computer models may be different. In such case, adjust the items V POSITION and H POSITION in the IMAGE menu. Back porch (B) Front porch (D) Back porch (b) Front porch (d) Active video (C) Active video (c) Data Data H. Sync. V. Sync. Sync (A) Sync (a) Horizontal signal timing (μs) Vertical signal timing (lines) Resolution Signal mode (H x V) (A) (B) (C) (D) (a) (b)
Résumé du contenu de la page N° 4
Connection to the ports Connection to the ports NOTICE ►Use the cables with straight plugs, not L-shaped ones, as the input ports of the projector are recessed. ►Only the signal that is input from the COMPUTER IN1 or IN2 can be output from the MONITOR OUT port. A B A B COMPUTER IN1, MONITOR OUT D-sub 15pin mini shrink jack • Video signal: RGB separate, Analog, 0.7Vp-p, 75Ω terminated (positive) • H/V. sync. signal: TTL level (positive/negative) •
Résumé du contenu de la page N° 5
Connection to the ports (continued) H I C D E F F G C D E F G COMPUTER IN2 G/Y, B/Cb/Pb, R/Cr/Pr, H, V BNC jack x5 • Video signal: RGB separate, Analog, 0.7Vp-p, 75Ω terminated (positive) • H/V. sync. signal: TTL level (positive/negative) • Composite sync. signal: TTL level • V ideo signal: Y with composite sync, Analog, 1.0±0.1Vp-p, 75Ω terminated Cb/Pb, Analog, 0.7±0.1Vp-p, 75Ω terminated Cr/Pr, Analog, 0.7±0.1Vp-p 75Ω terminated • System: 480i
Résumé du contenu de la page N° 6
Connection to the ports (continued) N M L K J J K L COMPONENT Y, Cb/Pb, Cr/Pr RCA jack x3 • Component video signal, Analog: -Y with composite sync, 1.0±0.1Vp-p, 75Ω terminated -Cb/Pb, 0.7±0.1Vp-p, 75Ω terminated -Cr/Pr, 0.7±0.1Vp-p 75Ω terminated • System: 480i@60, 480p@60, 576i@50, 720p@50/60, 1080i@50/60, 1080p@50/60 M S-VIDEO 4 2 Mini DIN 4pin jack 1 3 • S-video signal, Analog: -Brightness signal with composite sync, 1.0±0.1Vp-p, 75Ω terminated -Color signal, 0.286Vp-p (NTSC
Résumé du contenu de la page N° 7
Connection to the ports (continued) U O Q R S T P O P AUDIO IN1, AUDIO IN2 Ø3.5 stereo mini jack • Analog, 500 mVrms, 47kΩ input impedance AUDIO IN3 Q L, R R AUDIO OUT S L, T R RCA jack x2 RCA jack x2 • Analog, 500 mVrms, 47kΩ input impedance • Analog, 500 mVrms, 1kΩ output impedance U CONTROL D-sub 9pin plug * About the details of RS-232C communication, please refer to the next section. Pin Signal Pin Signal Pin Signal 1 (No connection) 4 (No connection) 7 RTS 2 RD 5 Grou
Résumé du contenu de la page N° 8
Connection to the ports (continued) W X V Y Z V LAN RJ-45 jack * About the details of network communication, please refer to the Network Guide. Pin Signal Pin Signal Pin Signal 1 TX+ 4 - 7 - 2 TX- 5 - 8 - 3 RX+ 6 RX- WUSB TYPE A X USB TYPE B USB A type jack x2 USB B type jack Pin Signal Pin Signal 1 +5V 1 +5V 2 - Data 2 - Data 3 + Data 3 + Data 4 Ground 4 Ground REMOTE CONTROL Y IN, Z OUT Ø3.5 stereo mini jack 8
Résumé du contenu de la page N° 9
Connection to the ports (continued) To input SCART RGB signal; ex. RCA plugs SCART cable Audio L (plug) Audio R Video R SCART B connector (jack) G To input SCART RGB signal to the projector, use a SCART to RCA cable. Connect the plugs refer to above ex. For more reference, please consult your dealer. 9
Résumé du contenu de la page N° 10
RS-232C Communication RS-232C Communication When the projector connects to the computer by RS-232C communication, the projector can be controlled with RS-232C commands from the computer. For details of RS-232C commands, refer to RS-232C Communication / Network command table ( &19). Connection Turn off the projector and the computer. 1. Connect the projector's CONTROL port and the computer's RS-232C port 2. with a RS-232C cable (cross). Use the cable that fulfi lls the specifi cation shown
Résumé du contenu de la page N° 11
RS-232C Communication (continued) Communicaion settings 1. Protocol 19200bps, 8N1 2. Command format ("h" shows hexadecimal) 7 8 9 10 11 12 Byte Number 0 1 2 3 4 5 6 Header Data Command Header Data CRC Setting Action Type code size flag code Packet Action L H L H L H L H L H L H Change setting to desired value [(cL)(cH)] (aL) (aH) 01h 00h (bL) (bH) (cL) (cH) by [(bL)(bH)]. Read projector internal setup value [(bL) (aL) (aH) 02h 00h (bL) (bH) 00h 00h (bH)] . BEh EFh 03h
Résumé du contenu de la page N° 12
RS-232C Communication (continued) 3. Response code / Error code ("h" shows hexadecimal) (1) ACK reply: 06h When the projector receives the Set, Increment, Decrement or Execute command correctly, the projector changes the setting data for the specified item by [Type], and it returns the code. (2) NAK reply: 15h When the projector cannot understand the received command, the projector returns the error code. In such a case, check the sending code and send the same command again. (3) Error
Résumé du contenu de la page N° 13
Command Control via the Network Command Control via the Network When the projector connects network, the projector can be controlled with RS- 232C commands from the computer with web browser. For details of RS-232C commands, refer to RS-232C Communication / Network command table ( &19). NOTE • If data is transferred via wireless and wired LAN at the same time, the projector may not be able to process the data correctly. Connection Turn off the projector and the computer. 1. If you use wired
Résumé du contenu de la page N° 14
Command Control via the Network Communicaion Port The following two ports are assigned for the command control. TCP #23 TCP #9715 Configure the following items form a web browser when command control is used. Port Settings Click the [Enable] check box to open [Network Port open Control Port1 (Port: 23)] to use TCP #23. Default setting is “Enable”. Network Control Click the [Enable] check box for the Port1 (Port: 23) [Authentication] setting when authentication Authentication is required. Def
Résumé du contenu de la page N° 15
Command Control via the Network (continued) Command control settings [TCP #23] 1. Command format Same as RS-232C communication, refer to RS-232C Communicaton command format. 2. Response code / Error code ("h" shows hexadecimal) Four of the response / error code used for TCP#23 are the same as RS-232C Communication (1)~(4). One authentication error reply (5) is added. (1) ACK reply : 06h Refer to RS-232C communication ( &12). (2) NAK reply : 15h Refer to RS-232C communication ( &12). (3) Er
Résumé du contenu de la page N° 16
Command Control via the Network (continued) 2. Response code / Error code ("h" shows hexadecimal) The connection ID is attached for the TCP#23's response / error codes are used. The connection ID is same as the sending command format. (1) ACK reply: 06h + ××h (××h : connection ID) (2) NAK reply: 15h + ××h (3) Error reply: 1Ch + 0000h + ××h (4) Data reply: 1Dh + xxxxh + ××h (5) Authentication error reply: 1Fh + 0400h + ××h (6) Projector busy reply: 1Fh + ××××h + ××h When the projector is too
Résumé du contenu de la page N° 17
Network Bridge Communication Network Bridge Communication This projector is equipped with NETWORK BRIDGE function. When the projector connects to the computer by wired or wireles LAN communicaton, an external device that is connected with this projector by RS- 232C communication can be controlled from the computer as a network terminal. For details, see the 6. Network Bridge function in the Network Guide. NOTE • If data is transferred via wireless and wired LAN at the same time, the projector
Résumé du contenu de la page N° 18
Network Bridge Communication Communication settings For communication setting, use the COMMUNICATION menu in the OPTION - SERVICE menu Item Condition BAUD RATE 4800bps / 9600bps / 19200bps / 38400bps Data length 8 bit (fixed) PARITY NONE/ODD/EVEN Start bit 1 bit (fixed) Stop bit 1 bit (fixed) Transmission method HALF-DUPLEX/FULL-DUPLEX For connecting the projector to your devices, please read the NOTE • manual for each devices, and connect them correctly with suitable cables. • Turn off th
Résumé du contenu de la page N° 19
RS-232C Communication / Network command table RS-232C Communication / Network command table Command Data CRC Names Operation Type Header Action Type Setting code Turn off BE EF 03 06 00 2A D3 01 00 00 60 00 00 Set Turn on BE EF 03 06 00 BA D2 01 00 00 60 01 00 BE EF 03 06 00 19 D3 02 00 00 60 00 00 Power [Example return] Get 00 00 01 00 02 00 [Off] [On] [Cool down] COMPUTER IN1 BE EF 03 06 00 FE D2 01 00 00 20 00 00 COMPUTER IN2 BE EF 03 06 00 3E D0 01 00 00 20
Résumé du contenu de la page N° 20
RS-232C Communication / Network command table (continued) Command Data CRC Names Operation Type Header Action Type Setting code LENS MEMORY Get BE EF 03 06 00 A0 91 02 00 0D 24 00 00 LENS SHIFT - V LENS MEMORY Get BE EF 03 06 00 E4 91 02 00 0E 24 00 00 LENS SHIFT - H LENS MEMORY Get BE EF 03 06 00 18 90 02 00 0F 24 00 00 LENS TYPE Get BE EF 03 06 00 7C D2 02 00 07 30 00 00 Increment BE EF 03 06 00 1A D2 04 00 07 30 00 00 MAGNIFY Decrement BE EF 03 06 00 CB D3
