Résumé du contenu de la page N° 1
LAN Control Utility
User Manual (for FL7000U)
Contents
Preparation/SetUp .........................................................................2
Preparation before using the network function ...........................................2
Connection .................................................................................................. 3
Installation ...................................................................................................3
Setting the IP address of the pro
Résumé du contenu de la page N° 2
Preparation/SetUp Preparation before using the network function This projector is equipped with the network function to control and monitor the projector’s operations using a Web browser and to send e-mail notifi cation. Before using the network function, perform the following three preparation steps. (1) Setup of the application software “Projector-Control Device Installer” *1 (2) Setting of the IP address of the projector (3) Setting of password, display language, LAN control, and PJLink™ c
Résumé du contenu de la page N° 3
Preparation/SetUp (continued) Connection Computer LAN cable (option) (100BASE-TX or 10BASE-T should be supported.) To LAN terminal LAN cable (option) (100BASE-TX or 10BASE-T should be supported.) External HUB � Use a straight-through category-5 cable for LAN connection. � Don’t touch the metal parts of the LAN connector and LAN cable because static electricity may be discharged from your body, causing damage to the projector. Installation Before starting installation, be sure to read “ReadMe.t
Résumé du contenu de la page N° 4
Preparation/SetUp (continued) Select a folder to install the program, and click Next. 4 Click Next. 5 Installation starts. 6 � The progress of the installation process is displayed as shown on the right. When the installation process is completed, click 7 Close. How to remove Projector-Control Device Installer Select [Start] - [Control Panel] - [Add or Remove Programs] - [Projector-Control Device Installer] and click [Remove] ® (in the case of Windows XP). EN-4
Résumé du contenu de la page N° 5
Preparation/SetUp (continued) Setting the IP address of the projector Before setting the IP address, check that the projector has been LAN-networked and turn on the main power of the projector. Start the Projector-Control Device Installer. 1 � Select [Start] - [All Programs] - [Projector] - [Projector-Control Device Installer] (in the case of ® Windows XP). Click the Search button. 2 � Projector is recognized. (Note) When projector isn’t recognized, check the following. � The fi rewall func
Résumé du contenu de la page N° 6
Preparation/SetUp (continued) When using a DHCP server Select [Obtain an IP address automatically] and click 5 Next. Click Next. 6 � Check that the options are marked with check- marks as shown on the right. Keep them un- changed for normal use. Click Assign. 7 Click Finish. 8 Click the Search button. 9 � Check the IP address. EN-6
Résumé du contenu de la page N° 7
Preparation/SetUp (continued) When not using a DHCP server Select [Assign a specifi c IP address] and click Next. 5 Enter a fi xed IP address (for example, 192.168.0.1) 6 and click Next. (Note) Do not use 0 or 255 for the last digit of the IP address. Click Assign. 7 Click Finish. 8 Click the Search button. 9 � Check the IP address you set. (Note) When using the error/alert e-mail notifi cation function described later, click the Assign IP button and set the subnet mask and default gateway
Résumé du contenu de la page N° 8
Preparation/SetUp (continued) Telnet setting Setting of password, display language, LAN control, and PJLink™ certifi cation using telnet. This section describes how to set the password, display language on the ProjectorView screen, LAN control, and PJLink™ certifi cation that are necessary for the operation state control tool (commercially available) that uses the projector operation control/monitor tool ProjectorView and the industry standard PJLink™ protocol. Start the Projector-Control Devic
Résumé du contenu de la page N° 9
Preparation/SetUp (continued) Setting the password (Password Setup) Enter “0” and press the Enter key. 1 Input the old (current) password and press the Enter 2 key. (Default password is admin.) � If you input a wrong password, an error message appears and the setting menu is displayed again. In this case, set the password again. � If you forget your password, select “7 factory defaults,” input the password “projectorcontroller,” and then select “9 save and exit” to perform initialization.
Résumé du contenu de la page N° 10
Preparation/SetUp (continued) Setting the display language of ProjectorView (language) Enter “1” and press the Enter key. 1 Enter “0” for English or “1” for Japanese. 2 Setting the LAN control (LAN-Controlled Mode) Enter “3” and press the Enter key. 1 To enable the e-mail notifi cation function of Projector- 2 View, enter 1 and press the Enter key. (Default is OFF (0).) (See pages 12 - 15 for ProjectorView function.) EN-10
Résumé du contenu de la page N° 11
Preparation/SetUp (continued) Setting the PJLink™ certifi cation (PJLink certifi cation Mode) Enter “5” and press the Enter key. 1 � When you don’t use PJLink™ protocol communication, skip this item. (See page 16 for PJLink™.) To enable the PJLink™ certifi cation, enter “1” and 2 press the Enter key. To disable it, enter “0” and press the Enter key. (Default is ON (1).) Save and exit Enter “9” and press the Enter key. 1 The setting screen is shaded and the setting is updated. 2 � It takes ab
Résumé du contenu de la page N° 12
ProjectorView Using the ProjectorView This section describes ProjectorView, a tool to control and monitor the projector’s operations by a Web browser. The major functions of ProjectorView are: � Power on/off � Input source switching � State information indication (projector’s name, temperature, lamp operation time, error/alert, etc.) � E-mail notifi cation in case of error/alert How to start up Start the Projector-Control Device Installer. 1 � Select [Start] - [All Programs] - [Projector] - [P
Résumé du contenu de la page N° 13
ProjectorView (continued) The password input screen appears. Enter the 5 password you set. � The default password is admin. (Note) If you input a wrong password three successive times, the Web browser is closed. In this case, repeat from step 1. The ProjectorView main screen appears. 6 � Some buttons may not be displayed. In this case, select [Start] - [Control Panel] - [Java Plug-in] and disable the cache. [ProjectorView main screen] Press to display the Setup win- dow. (See page 15.) P
Résumé du contenu de la page N° 14
ProjectorView (continued) VIRTUAL REMOTE controller Put a checkmark in the box of the Virtual remote enabled on the ProjectorView main screen, and click the VIRTUAL REMOTE button. The following Virtual Remote window appears. For the functional descriptions of each button, see the user manual of the projector. E-mail notifi cation function In case of an error or abnormality in the projector, e-mail notification is automatically sent to the designated address to notify of the error or abnormalit
Résumé du contenu de la page N° 15
ProjectorView (continued) Initial setting To load information on the projector such as model name and lamp operating time, set the projector data in advance. Click the SETUP button on the ProjectorView main screen. The Projector Setup screen appears. Enter data according to the description of each setting item. (Note) � You can’t change the Projector model, Serial number, Operating hours, and Lamp hours. They are loaded from the projector and displayed when the LAN controlled mode of Telnet
Résumé du contenu de la page N° 16
Support for the PJLink™ function This projector supports standard protocol PJLink™ for projector control and you can control and monitor projector’ s operations using the same application among projectors of different models and different manufacturers. To use this function, set the PJLink™ certifi cation properly according to the setting of the PJLink™ application to be used. (See page 11.) Supported commands The table below shows commands to control the projector using the PJLink™ protocol
Résumé du contenu de la page N° 17
Support for the PJLink™ function (continued) [Notes on Instant Shut Down] Instant shutdown of the projector during control using the network function may cause ProjectorView to fail to display data correctly. � The operating time and temperature may not be displayed correctly. In this case, close the browser, recognize this projector using Projector-Control Device Installer, and then start the browser again. (Refer to “How to start up” of ProjectorView.) � When you use the e-mail notifi cati
