Résumé du contenu de la page N° 1
R
LCD Projector Commercial Use
Operating Instructions
Model No. PT-LB10NTE
PT-LB10E
PT-LB10VE
PT-LB10SE
POWER
INPUT
VIDEO RGB
AUTO
MENU
SETUP
ENTER
FREEZE SHUTTER
STD
VOLUME D.ZOOM
INDEX
WINDOW
PROJECTOR
Before operating this product, please read the instructions carefully and save this
manual for future use.
TQBJ 0142
ENGLISH
Résumé du contenu de la page N° 2
Dear Panasonic Customer: This instruction booklet provides all the necessary operating information that you might require. We hope it will help you to get the most out of your new product, and that you will be pleased with your Panasonic LCD projector. The serial number of your product may be found on its bottom. You should note it in the space provided below and retain this booklet in case service is required. Model number: PT-LB10NTE / PT-LB10E / PT-LB10VE / PT-LB10SE Serial number: IMPORTANT
Résumé du contenu de la page N° 3
WARNING: BFor permanently connected equipment, a readily accessible disconnect device shall be incorporated in the building installation wiring; BFor pluggable equipment, the socket-outlet shall be installed near the equipment and shall be easily accessible. CAUTION: To assure continued compliance, follow the attached installation instructions, which includes using the provided power cord and shielded interface cables when connecting to computer or peripheral device. If you use serial port to co
Résumé du contenu de la page N° 4
IMPORTANT: THE MOULDED PLUG (U.K. only) FOR YOUR SAFETY, PLEASE READ THE FOLLOWING TEXT CAREFULLY. This appliance is supplied with a moulded three pin mains plug for your safety and convenience. A 13 amp fuse is fitted in this plug. Should the fuse need to be replaced, please ensure that the replacement fuse has a rating of 13 amps and that it is approved by ASTA or BSI to BS1362. ASA Check for the ASTA mark or the BSI mark on the body of the fuse. If the plug contains a removable fu
Résumé du contenu de la page N° 5
Contents White balance R/G/B, AI, Preparation TV-SYSTEM, STILL MODE, IMPORTANT SAFETY NOTICE ...2 SIGNAL MODE, Projecting sRGB- Precautions with regard to compatible pictures safety .........................................6 Adjusting the position...............40 POSITION, DOT CLOCK, CLOCK Accessories ...............................10 PHASE, ASPECT, RESIZING, Before use ..................................11 FRAME LOCK Location and function of each Changing the display part.....................
Résumé du contenu de la page N° 6
Precautions with regard to safety WARNING If you notice smoke, strange smells or noise coming from the projector, disconnect the mains plug from the mains socket. BDo not continue to use the projector in such cases, otherwise fire or electric shocks could result. BCheck that no more smoke is coming out, and then contact an Authorised Service Centre for repairs. BDo not attempt to repair the projector yourself, as this can be dangerous. Do not install this projector in a place which is not strong
Résumé du contenu de la page N° 7
Do not do anything that might damage the mains lead or the mains plug. BDo not damage the mains lead, make any modifications to it, place it near any hot objects, bend it excessively, twist it, pull it, place heavy objects on top of it or wrap it into a bundle. BIf the mains lead is used while damaged, electric shocks, short-circuits or fire may result. BAsk an Authorised Service Centre to carry out any repairs to the mains lead that might be necessary. Do not handle the mains plug with wet hand
Résumé du contenu de la page N° 8
During a thunderstorm, do not touch the projector or the cable. BElectric shocks can result. Do not use the projector in a bath or shower. BFire or electric shocks can result. Do not look into the lens while the projector is being used. BStrong light is emitted from the projector’s lens. If you look directly into this light, it can hurt and damage your eyes. BBe especially careful not to let young children look into the lens. In addition, disconnect the mains plug when you are away from the proj
Résumé du contenu de la page N° 9
Do not short-circuit, heat or disassemble the batteries or place them into water or fire. BFailure to observe this may cause the batteries to overheat, leak, explode or catch fire, and burns or other injury may result. When inserting the batteries, make sure the polarities (+ and -) are correct. BIf the batteries are inserted incorrectly, they may explode or leak, and fire, injury or contamination of the battery compartment and surrounding area may result. Use only the specified batteries. BIf i
Résumé du contenu de la page N° 10
Accessories Check that all of the accessories shown below have been included with your projector. Card remote control unit Lithium battery for RGB signal cable (TNQE239 x1) remote control unit [1.8 m (5´10˝), (CR2025 x1) K1HA15DA0002 x1] POWER INPUT VIDEO RGB AUTO MENU SETUP ENTER Mains lead for Mains lead for U.K. FREEZE SHUTTER Continental Europe (K2CT3DR00005 x 1) (K2CM3DR00002 x 1) STD VOLUME D.ZOOM INDEX WINDOW PROJECTOR Carrying bag (TPEP013 x 1) PT-LB10NTE only CD-ROM Wireless Card Hexag
Résumé du contenu de la page N° 11
Before use Caution when moving the projector Be sure to attach the lens cover before moving the projector. The projection lens is extremely susceptible to vibration and shocks. When moving the projector, use the accessory carrying bag. When placing the projector inside the carrying bag, position it so that the lens is facing upward. Do not put anything else in the bag other than the projector and the cables. Cautions regarding setting-up Avoid setting up in places which are subject to vibration
Résumé du contenu de la page N° 12
Notes on use In order to get the best picture quality Draw curtains or blinds over any windows and turn off any fluorescent lights near the screen to prevent outside light or light from indoor lamps from shining onto the screen. Do not touch the surfaces of the lens with your bare hands. If the surface of the lens becomes dirty from fingerprints or anything else, this will be magnified and projected onto the screen. Moreover, when not using the projector, retract the lens and then cover it with
Résumé du contenu de la page N° 13
Location and function of each part Projector #$% + & ' * ) ' ( #Projector control panel (page 16) $Zoom ring (page 25) %Focus ring (page 25) &Security lock This can be used to connect a commercially-available theft-prevention cable (manufactured by Kensington). This security lock is compatible with the Microsaver Security System from Kensington. 'Leg adjuster buttons (L/R) (page 25) These buttons are used to unlock the front adjustable legs. Press to adjust the angle of t
Résumé du contenu de la page N° 14
Projector $%$ # ( ' & #Connector panel (page 15) $Air outlet port Do not cover this port. %Speaker &Front adjustable legs (L/R) (page 25) 'Air inlet port, Air filter (page 52) Do not cover this port. (Lamp unit holder (page 53) NOTE: BDuring projection of an image, the cooling fan will operate, emitting a small noise as it operates. Turning the lamp on or off will cause this noise to increase a little. BBy using the “OPTION2” menu to set “LAMP POWER” to “LOW”, the operating sou
Résumé du contenu de la page N° 15
Connector panel $%& ' ) * # ( #Power input socket (AC IN) (page 24) The accessory mains lead is connected here. Do not use any mains lead other than the accessory mains lead. $SERIAL connector (pages 21, 22 and 62) This connector is used to connect a personal computer to the projector in order to control the projector externally. (RS-232C compatible) %RGB IN connector (pages 21 and 22) This connector is used to input RGB signals and YPBPR signals. &RGB OUT connector (page 21) This connector is u
Résumé du contenu de la page N° 16
Projector control panel Menu operation #$% & ' ( * ) +, Remote control unit ' POWER INPUT ( ) VIDEO RGB * + AUTO MENU SETUP , - ENTER . / FREEZE SHUTTER 0 STD VOLUME D.ZOOM INDEX WINDOW 1 2 PROJECTOR #RGB INPUT indicator This indicator illuminates when a signal is being input to the RGB IN connector. $LAMP indicator (page 51) This indicator illuminates when it is time to replace the lamp unit. It flashes if a circuit abnormality is detected. 16-ENGLISH
Résumé du contenu de la page N° 17
%TEMP indicator (page 50) This indicator illuminates if an abnormally high temperature is detected inside the projector or around it. If the temperature rises above a certain level, the power supply will be turned off automatically and the indicator will flash. &Power indicator (pages 24, 26 and 27) This indicator illuminates red when the projector is in standby mode, and it illuminates green when a picture starts to be projected. 'POWER button (pages 24 and 26) (INPUT buttons (page 25) These bu
Résumé du contenu de la page N° 18
(PT-LB10NTE only) Wireless card $ # #Connector This connector is for connecting the wireless card to the projector’s card slot. Be careful not to touch the connector. $Wireless card access indicator Flashes while the projector is being accessed with personal computers by means of a wireless network. Inserting the wireless card (PT-LB10NTE only) Insert the wireless card before using the PT-LB10NTE. The card lock is already installed at the factory default setting. When you insert the wireless car
Résumé du contenu de la page N° 19
Setting-up Projection methods In way of installing projector, any one of the following four projection methods are used. Select whichever projection method matches the setting-up method. (The projection method can be set from the “OPTION2” menu. Refer to page 45 for details.) BFront-desk projection BFront-ceiling projection Menu items Setting Menu items Setting FRONT/REAR FRONT FRONT/REAR FRONT DESK/CEILING DESK DESK/CEILING CEILING BRear-desk projection BRear-ceiling projection (Using a translu
Résumé du contenu de la page N° 20
Projector position Top edge of screen L: Projection distance Screen SH: Image height L SW:Image width H1: Distance from centre Bottom edge of screen of lens to bottom edge of projected image L Screen Projection distances Projection distance (L) PT-LB10NTE/PT-LB10E/ 4:3 Screen Height PT-LB10VE PT-LB10SE size position (diagonal) (H1) Wide Telephoto Wide Telephoto (LW) (LT) (LW) (LT) —— 0.84 m(33˝) 1.1 m(3´7˝) 1.1 m(3´7˝) 0.08 m(3-1/8˝) 1.02 m(40˝) 1.2 m(3´11˝) 1.4 m(4´7˝) 1.2 m(3´11˝) 1.4 m(4´7˝)
