Résumé du contenu de la page N° 1
Installation and Assembly - All-in-one Projector Adapter Plate for
Model: SP-CEIL-UNIV
®
InFocus Projectors
This product is intended for use with UL
Maximum Load Capacity: 25 lb (11 kg)
Listed products and must be installed
by a qualified professional installer.
Read instruction sheet before you start installation and assembly.
WARNING
• Make sure that the supporting surface will safely support the combined load of the equipment and all attached hard-
ware and components.
IMPORTANT! Turn to
Résumé du contenu de la page N° 2
Before you start check the parts list to insure all of the parts shown are included. Parts List Description Qty. Part Number A projector mount assembly 1 055-0420 B 4 mm security allen wrench 1 560-9646 C #10-32 x 3/8" serrated socket pin screw 2 520-1151 D #10-32 x 1/4" socket pin screw 1 520-1196 E 1/4" flat washer 2 540-9440 F #14 x 2.5 phillips hex head wood screw 2 5S1-015-C03 G concrete anchor 2 590-0097 H M4 x 16 mm serrated socket pin screw 3 510-1087 I M4 x 12 mm serrated socket pin scr
Résumé du contenu de la page N° 3
Disengage connection block from projector mount assembly (A) by unscrewing captive screw and sliding out connection block as shown. A CONNECTION BLOCK CAPTIVE SCREW Installation To Wood Joist Finished Ceilings, Exposed Wood Joists, or Wood Beam Ceilings Drill two 5/32" (4 mm) dia. holes to a minimum depth of 2.5" (64 mm). Attach ceiling plate (Q) with two #14 x 2.5" (6 mm x 65 mm) wood screws (F) as WOOD JOIST shown using 3/8" (10 mm) socket wrench. Tighten wood screws (F) so ceiling plate (Q) i
Résumé du contenu de la page N° 4
Installation to Concrete Ceilings ® Alligator concrete anchors are recommended. Drill two 1/4" (6 mm) dia. holes to a minimum depth of 2.5" (64 mm). Attach ceiling plate (Q) using two concrete anchors (G) and #14 x 2.5" wood screws (F) G as shown in Illustration A and 1, 2, and 3. Tighten all fasteners. Skip to step 7. CONCRETE CEILING Q WARNING F • Make sure that the supporting surface will safely support the combined load of the equipment and all attached hardware and components. • Tighten co
Résumé du contenu de la page N° 5
Flush Mount Installation Drill two 5/32" (4 mm) dia. holes to a minimum depth of 2.5" (64 mm). Attach projector mount assembly (A) with two #14 x 2.5" (6 mm x 65 mm) wood screws (F) and two flat washers (E) as shown in figure 1 or figure 2 depending on joist orientation. Tighten wood screws (F) using 3/8" (10 mm) socket wrench until projector mount assembly (A) is firmly attached. WARNING • Tighten wood screws so that projector mount assem- bly is firmly attached, but do not overtighten. Overti
Résumé du contenu de la page N° 6
Installation to Extension Column (SP-EXTARM-01, SP- EXTARM-02, SP-EXTARM-03, SP-EXTARM-04) Q Screw extension column (sold separately) to ceiling plate (Q). Align the notch with one of the four holes in the ceiling plate (Q) and secure extension column with a M5 x 10 mm socket pin screw (M) using security allen wrench (B). See detail 3. Screw projector mount assembly (A) onto the EXTENSION COLUMN extension column as shown in detail 4. N M (SOLD SEPARATELY) (UL LISTED) Note: For 3/4" extension col
Résumé du contenu de la page N° 7
Installation to LIGHTWEIGHT SUSPENDED CEILING Lightweight Suspended PLATE (SOLD SEPARATELY) Ceiling Plate (EXT-LTMT-PLTB) Refer to instruction sheet for lightweight suspended ceiling plate (sold RETAINING COLLAR separately) for attachment of ceiling plate to ceiling. M Screw extension column (sold separately) to retaining collar in ceiling N tray. Align the notch with one of the four holes in retaining collar and secure extension column with a M5 x 10 mm DETAIL 6 socket pin screw (M) using secur
Résumé du contenu de la page N° 8
Note: The projector adapter plate and projector you are installing may differ in appearance from the sample illustrated below. Align shoulder on connection block opposite of front of projector. Attach adapter plate (R) to connection block from projector mount assembly (A) using two #10-32 x 3/8" serrated socket pin screws (C) as shown. CONNECTION BLOCK SHOULDER ADAPTER PLATE R FRONT OF PROJECTOR C P R Attach extension brackets (S) to adapter plate (R) using two M4 x 6 mm serrated socket pin s
Résumé du contenu de la page N° 9
Flip projector upside down. Find your projector from the models listed below. Using the holes indicated on the corre- sponding hole pattern diagram, attach adapter plate (R) to projector using three M4 x 16 mm serrated socket pin screws (H) and three .198 x .313 x .375 retaining spacers (J). Notes: Retaining spacers go between adapter plate and projector. * Front of projector. ** Projectors using hole pattern G use one M4 x 12 mm screw (I) and one .198 x .313 x .187 retaining spacer (K) where in
Résumé du contenu de la page N° 10
J. IN72, IN74, IN76 K. IN24, IN26 * * R R WARNING • Always use an assistant or mechanical lifting equipment to safely lift and position the projector. Slide connection block with projector into projector mount IMPORTANT: For security installations, insert assembly (A) as shown. Tighten captive screw to secure one #10-32 x 1/4" socket pin screw (D) through projector to projector mount assembly (A). projector mount assembly (A) and into connection block as shown. CONNECTION BLOCK A CONNECTION BL
Résumé du contenu de la page N° 11
Projector Alignment Projector Alignment Projector Alignment Projector Alignment Projector Alignment To adjust yaw (swivel) for wood stud, concrete ceiling, and threaded rod mounting applications: Loosen wood screws (F), or locknuts for threaded rods, until projector mount can be rotated. Rotate mount to desired position and retighten screws or locknuts. To adjust yaw (swivel) for extension column applications: Loosen screw on projector mount assembly (A) indicated below until projector mount
