Résumé du contenu de la page N° 1
MAXI® Remote Location Kit
MRLK 900
Installation Instructions
Résumé du contenu de la page N° 2
Introduction The MAXI® Remote Location Kit 900 utilizes 900 MHz radios to position a MIM 2-Wire, MIM LINK or MDI at a remote location from the central computer. The MRLK 900 includes two surge protectors to provide in-line protection against lightning at the locations of both radios. These installation instructions assume that the user is already familiar with the installation instructions and physical layout of the MIM 2-Wire, MIM LINK, or MDI products. If further information is nee
Résumé du contenu de la page N° 3
To MIM Antenna Prior to Installation 5 4 6 6 To MIM Antenna 1 1 MASTER SLAVE Existing cable 4 4 3B and connector 3A AC POWER AC POWER 2 2 After MRLK 900 Installation FIGURE 1
Résumé du contenu de la page N° 4
Radio Configuration Prior to the installation of the MRLK 900, the FreeWave 900 MHz Spread Spectrum radios require configuration. All adjustments are done through the FreeWave setup program, a user interface which eliminates the need for setup diskettes, DIP switch settings, or custom software. The setup program is invoked by connecting the FreeWave radio to any terminal program, setting the computer baud rate to 19,200, and putting the radio into setup mode. The configuration can be p
Résumé du contenu de la page N° 5
4. Enter a Name for the New Connection (temporary name). 5. Select “Direct to Com1” from Connect Using pull-down. 6. Select the following settings for the COM1 Properties window: Bits per second: 19200 Data bits: 8 Parity: None Stop bits: 1 Flow control: None
Résumé du contenu de la page N° 6
7. Invoke the setup program by pressing the black button on the back of the radio: Setup Button When the setup program is invoked, all three LEDs on the front panel of the FreeWave radio will turn green and will remain green for the entire time the radio is in setup mode. 8. Verify that the serial number on the setup program screen matches the serial number on the bottom of the FreeWave radio. In addition to providing the radio’s unique serial number, the setup program provides a
Résumé du contenu de la page N° 7
be verified by checking the second line of text in the SET MODEM MODE menu as shown below. The second line of text should show the following: For Master radio: Modem Mode is 0 For Slave radio: Modem Mode is 1 If the radios have not been pre-configured correctly for the Modem Mode, then configure each radio using the following: For Master radio: Enter “0” to select Point to Point Master. For Slave radio: Enter “1” to select Point to Point Slave. If the Modem Mode has be
Résumé du contenu de la page N° 8
10. Verify that each radio has been pre-configured to communicate with the other by checking the entries in the Call Book for each radio. Enter “2” to Edit Call Book from the Main Menu. For Master radio: The Number for Entry (0) should match the serial number found on the bottom of the Slave radio. For Slave radio: The Number for Entry (0) should match the serial number found on the bottom of the Master radio. To change the Number of an entry, enter the entry number followed by t
Résumé du contenu de la page N° 9
11. Determine the baud rate setting for the MIM by looking at the baud rate select jumper on the inside of the door as shown below. Use the table below to determine the selected baud rate of the MIM. The baud rate setting for an MDI application can be determined from the existing configuration. Jumper Baud Rate E5 – E4 9,600 E4 – E3 1,200 12. Enter “1” to Set Baud Rate from the Main Menu. From the Set Baud Rate Menu, enter a “6” - 9,600 or a “9” - 1,200 to match the baud rat
Résumé du contenu de la page N° 10
13. After completing the setup program for one of the radios, perform steps 7-13 for the other radio, making sure that the Operation Mode selection is set to the opposite mode of the other radio. After configuring both radios, exit from the HyperTerminal program by closing the window or using the Exit selection in the File dropdown menu. Select Yes to disconnect from the current session of HyperTerminal. Yagi Antenna Installation Prior to the installation of the radios and the ante
