Résumé du contenu de la page N° 1
GAS HOB
ZGF 982
INSTRUCTION BOOKLET
Please read this instruction booklet before using the appliance
GB
Résumé du contenu de la page N° 2
Important Safety Information You MUST read these warnings carefully before installing or using the hob. If you need assistance, contact our Customer Care Department on 08705 727727 Installation This appliance must be installed and serviced by a Never use plastic or aluminium foil dishes on the hob. competent person as stated in the Gas Safety Perishable food, plastic items and areosols may be (Installation and Use) Regulations Current Editions affected by heat and should not be stored above o
Résumé du contenu de la page N° 3
Contents For the Installer For the User Important Safety Information 2 Instructions for the Installer 8 Description of the Hob 3 Important safety requirements 9 Operation 4 Installation 10 Maintenance and Cleaning 5 Building In 11 Something Not Working? 6 Electrical connections 12 Guarantee Conditions 7 Wiring Diagram 13 Fault Finding 13 This appliance complies with the following Commissioning 15 E.E.C. Directives: * 73/23 - 90/683 Conversion from Natural Gas to LPG 15 (Low VoltageDirective); *
Résumé du contenu de la page N° 4
Operation Hob burners To light a burner: turn the relevant control knob anticlockwise to the maximum position, then push it down to ignite the burner; then, check the flame is regular and adjust it as required. If you cannot light the flame even after several attempts, check the "cap" and “crown” (see Fig. 1 - letter A and B) are in the correct position. To put the flame out, turn the knob to the symbol . When switching on the mains, after installation or a power cut, it is quite normal
Résumé du contenu de la page N° 5
Maintenance and Cleaning Before any maintenance or cleaning can be carried out, you must DISCONNECT the hob from the electricity supply. The hob is best cleaned whilst it is still warm, as spillage can be removed more easily than if it is left to cool. The Hob Top Regularly wipe over the hob top using a soft cloth well wrung out in warm water to which a little washing up liquid has been added. Avoid the use of the following: - household detergent and bleaches; - impregnated pads unsuitable for n
Résumé du contenu de la page N° 6
YES Cast Iron Pan Supports The hob has cast iron pan supports. Take care when removing them. They are very heavy and could damage the hob or your kitchen furniture if you let them fall down. To keep the pan supports in the correct position, they are hooked into hinges at the back of the hob. When removing the pan supports, lift them up as shown in the diagram. Never turn the pan supports on the hinges, this could damage them. Wash the pan supports using hot soapy water. If necessary, a paste cle
Résumé du contenu de la page N° 7
Customer Care Department For general enquiries concerning your Zanussi appliance or for further information on Zanussi products, please contact our Customer Care Department by letter or tel- ephone at the address below or visit our website at www.zanussi.co.uk Customer Care Department ZANUSSI 55-77 High Street Slough Berkshire SL1 1DZ 08705 727727 (*) * calls to this number may be recorded for training purposes. Guarantee Conditions Zanussi Guarantee conditions We, Zanussi, undertake that if, wi
Résumé du contenu de la page N° 8
Instructions for the Installer Engineers technical data OVERALL DIMENSIONS Rear Left Burner (semi rapid) Heat Input 2.0 kW (6824 BTU/HR) Width: 860 mm Depth: 510 mm Front Left Burner (auxiliary) Heat Input 1.0 kW (3413 BTU/HR) CUT OUT DIMENSIONS Rear Right Burner (semi rapid) Width: 830 mm Heat Input 2.0 kW (6824 BTU/HR) Depth: 480 mm Front Right Burner (rapid) Heat Input 3.0 kW (10236 BTU/HR) SUPPLY CONNECTIONS Gas: Central Burner (Ultra-rapid Triple-crown) R 1/2 inch (1/2 inch male) Rear right
Résumé du contenu de la page N° 9
100 mm 100 mm 50 mm 50 mm 50 mm 50 mm 600 mm 600 mm Important safety requirements This hob must be installed in accordance with the Gas FITTING THE GAS HOB WITHOUT A COOKER HOOD ABOVE Safety (Installation and Use) Regulations (Current Edition) and the IEE Wiring Regulations (Current Edition). Provision for ventilation Detailed recommendations are contained in the following 700 mm British Standards Codes Of Practice: B.S. 6172/ B.S. 5440, Part 2 and B.S. 6891 Current Editions. 400 mm The hob shou
Résumé du contenu de la page N° 10
Installation IMPORTANT: This hob must be installed by a competent person to the relevant Gas Standards. Any gas installation must be carried out by a competent person. The manufacturer will not accept liability, should the above instructions or any of the other safety instructions incorporated in this book be ignored. WHEN THE HOB IS FIRST INSTALLED Once the hob has been installed, it is important to remove any protective materials, which were put on in the factory. On the end of the shaft, whic
Résumé du contenu de la page N° 11
Building In Building over a cupboard or Building over a kitchen unit with drawer door If the hob is to be installed above a cupboard or drawer it Proper arrangements must be taken in designing the will be necessary to fit a heat resistant board below the furniture unit, in order to avoid any contact with the bottom base of the hob on the underside of the work surface. of the hob which can be heated when it is operated. The It is also recommended to carry out the electrical recommended solution i
Résumé du contenu de la page N° 12
Seal a FO 0199 Electrical connections Any electrical work required to install this hob Permanent Connection should be carried out by a qualified electrician or In the case of a permanent connection, it is necessary competent person, in accordance with the current that you install a double pole switch between the hob regulations. and the electricity supply (mains), with a minimum gap of 3 mm. between the switch contacts and of a type suitable for the required load in compliance with the THIS HOB
Résumé du contenu de la page N° 13
Wiring Diagram L 1 A 0 2 N A. IGNITOR SWITCH 3 B. IGNITOR UNIT 4 220/240 L 5 6 B N Fault Finding Preliminary Electrical Systems PLUG (with cover SOCKET removed) (face view) Check ( ) Earth Wire ( ) E Brown Blue Green/Yellow START Isolate appliance Neutral Wire and carry out: Blue A: Earth Continuity N L check. Blue Green Brown Yellow Carry out: Electricity supply YES NO Carry out: D: Resistance to should now be C: Polarity check. Earth check. satisfactory. A. EARTH CONTINUITY CHECK - Applian
Résumé du contenu de la page N° 14
Ignition System / Gas Ignition YES Check gas supply at Ignitor does not spark burner NO Check plug top fuse and Light burner manually replace if necessary Check polarity and Check by pass simmer earth continuity of adjusted supply point Check position of the Check earth continuity electrode of appliance Check continuity from the tip of Check fitting of burners Check continuity from 'N' on the each electrode to the mains connector block and "O" on terminals 1 to 4 on the ignitor the ignitor unit
Résumé du contenu de la page N° 15
Commissioning When the hob has been fully installed it will be necessary to check the minimum flame setting. To do this, follow the procedure below. - Turn the gas tap to the MAX position and ignite. - Set the gas tap to the MIN flame position then turn the control knob from MIN to MAX several times. If the flame is unstable or is extinguished follow the procedure below. Procedure: Re-ignite the burner and set to MIN. Remove the control knob. To adjust, use a thin bladed screwdriver and turn th
Résumé du contenu de la page N° 16
CUSTOMER CARE ZANUSSI 55-77 High Street Slough Berkshire, SL1 1DZ Tel: 08705 727727 Long Mile Road Dublin 12 Republic of Ireland Tel: + 353 (0) 1 4090751 © Electrolux plc 2003 From the Electrolux Group. The world’s No.1 choice. The Electrolux Group is the world’s largest producer of powered appliances for kitchen, cleaning and outdoor use. More than 55 million Electrolux Group products (such as refrigerators, cookers, washing machines, vacuum cleaners, chain saws and lawn mowers) are so
