Résumé du contenu de la page N° 1
TND4204VX
VANDAL RESISTANT DOME CAMERA
INSTRUCTION MANUAL
CAUTION INFORMATION
RISK OF ELECTRIC SHOCK
This equipment has been tested and found
DO NOT OPEN
to comply with the limits for Class A digital
CAUTION : TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK).
device, pursuant to Part 15 of the FCC
NO USER SERVICEABLE PARTS INSIDE.
Rules. These limits are designed to
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
The lightning flash with arrowhead symbol, within
p
Résumé du contenu de la page N° 2
IMPORTANT SAFETY INSTRUCTIONS 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Clean only with dry cloth. 6. Do not block any ventilation openings, install in accordance with the manufacturer's instructions. 7. Do not install near heat sources such as radiators, heat registers, stoves or other apparatus (including amplifiers) that produce heat. 8. Only use attachment/accessories specified by the manufacturer. 9. Unplug this apparatus du
Résumé du contenu de la page N° 3
Name and Function of Each part 1 2 6 3 4 5 No. Name Function Camera mounting bracket The mounting bracket for ceiling installation. 1 Main body 2 The main body of the camera section. 3 Zoom ring For adjusting the image size. Focus ring 4 For adjusting the focus. 5 Cover lens Protective cover for the lens. Dome cover main body 6 Protective cover for the main body. 2
Résumé du contenu de la page N° 4
17 11 9 15 10 14 16 8 7 17 16 12 13 No. Name Function 7 AW PUSH Used when the white balance is in the PUSH mode. DOWN/UP 8 For setting the vertical sync. phase. 9 ALC adjustment volume For adjusting the brightness of the image. Tilt lock screw 10 For locking the tilt after adjusting the image up/down direction. Connect this to output images. When adjusting the image Monitor terminal 11 shooting direction, field angle or focus (in wiring work, for example), connect a monitor TV, etc. Image outpu
Résumé du contenu de la page N° 5
14 Selector switch (Details) 5 1/100S 1.SENS UP switch To set the max. value (upper limit value) of the 4 PUSH/ATW operating gain in the auto gain control circuit, set this switch to ON position. In case the back lighting is too INT/LL 3 dark and the camera sensitivity is insufficient, set this 2 BLC switch to ON position. 1 SENS UP 2. BLC (Back Light Control) switch In case the back lighting is too bright to view the ON OFF (This figure shows the setting main object clearly, set this switch to
Résumé du contenu de la page N° 6
How to Install 1. Make holes in the mounting surface. Front of camera (Fig. 1) The paper pattern for installation is included. (Fig. 1) Camera 2. Remove the dome cover main body mounting fixing screws from the camera body. bracket (Fig. 2). Use the dedicated wrench (Attached). Be careful not to drop the cover Dome cover dome. main body Cover dome screw Dedicated wrench (Attached) (Fig.2) 5
Résumé du contenu de la page N° 7
Camera mounting bracket 3. Remove the main body fixing screws, and remove the main body from the camera mounting bracket. (Fig. 3). Main body Main body mount screw (Fig.3) Remove the screws identified by the mark(Figs. 4). (Fig.4) Camera mounting 4. Fix the camera body to ceiling, wall or bracket box with the camera body fixing screws. Front of (Fig.5) camera Make sure that it is fixed firmly. Make sure of the position of the front of the camera. Camera mounting bracket mount screw (not attache
Résumé du contenu de la page N° 8
5. Connect the power cord and the BNC Camera mounting bracket cable, and then mount the main body on the camera body. (Fig. 6). Weight of the camera mounting bracket and mounting metal piece is 1600g(3.52 lbs). BNC Make sure that the ceiling or wall cable Warning is strong enough to support the weight of the camera mounting Power cord bracket and mounting metal Main body piece altogether.If not strong enough, the device may drop and injure the personnel around. · When you connect the Power cord
Résumé du contenu de la page N° 9
Be careful not to drop the tilt lock Camera mounting bracket screw. Tilt lock screw Manually fasten the tilt lock screw. If fastened with pliers or the like, the tilt lock screw may be broken. Lens (Fig.8) 7. Correct the image tilt. (Fig.9) Cover motor Be sure to hold the cover motor. Lens (Fig.9) 8. Mount the cover lens, and mount the Main body dome cover with the dome cover fixing screws. (Fig.10) Dome cover Cover lens (Fig.10) 8
Résumé du contenu de la page N° 10
When any failure is suspected Symptoms Check here. Image is not displayed. Are cables connected correctly? Are the power plugs of peripheral units inserted correctly into the receptacles? Is the video monitor adjusted correctly? Color is not correct. Is any connector of this machine or video monitor loose or Image is disarrayed. contacted poorly? Appearance All dimensions in mm(inch) 166(6.54) 101.6(4.00) 9
Résumé du contenu de la page N° 11
Specifications Model TND4204VX Power source AC24V(AC15V-27V) 60Hz 0.5Hz or DC12V(DC11V-35V) Power consumption AC : Approx.2.5W or DC : Approx.2.8W Image pick-up device 1/3" color interline-transfer CCD Effective picture element 768(H) 494(V) Scanning area 4.88mm(H) 3.66mm(V) Scanning system 2:1interlaced Scanning frequency LL : 15.75kHz (H), 60Hz (V) INT : 15.734kHz (H), 59.94Hz (V) Sync.system AC : Line-lock/Internal (switchable) DC : Internal Resolution 480TV lines(H) 350TV lines(V) S/N rati
Résumé du contenu de la page N° 12
and are registered trademarks of ELMO COMPANY, LIMITED. 6-14, Meizen-cho, Mizuho-ku, ELMO CO., LTD. Nagoya, 467-8567 Japan E-mail : foreign-div@elmo.co.jp OVERSEAS SUBSIDIARY COMPANIES ELMO Mfg. Corp. ELMO Canada Mfg. Corp. ELMO (Europe) G.m.b.H. 1478 Old Country Road, 44 West Drive, Brampton, Neanderstr. 18 Plainview, NY 11803-5034 Ontario, L6T 3T6, 40233 Dusseldorf, U.S.A. Canada Germany Tel. 516-501-1400 Tel. 905-453-7880 Tel. 0211-376051-53 Fax. 516-501-0429 Fax. 905-4
