Résumé du contenu de la page N° 1
Day/Night
Ultra Wide Dynamic
Fixed Dome Camera
NTSC / PAL
HD4U HD4UX
User Guide
Document 800-00031 – Rev A – 04/08
Résumé du contenu de la page N° 2
Revisions Issue Date Revisions A 04/08 New document. 2
Résumé du contenu de la page N° 3
Warnings Installation and servicing should be performed only by qualified and experienced technicians to conform to all local codes and to maintain your warranty. WARNING! 12 VDC/24 VAC models require the use of CSA Certified/UL Listed Class 2 power adapters to ensure compliance with electrical safety standards. WEEE (Waste Electrical and Electronic Equipment). Correct disposal of this product (applicable in the European Union and other European countries with separate collection systems).
Résumé du contenu de la page N° 4
FCC Compliance Statement Information to the User: This equipment has been tested and found to comply with the limits for a Class B digital device. Pursuant to Part 15 of the FCC Rules, these limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio commun
Résumé du contenu de la page N° 5
Contents Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Before You Begin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Unpack Everything . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Equipment Required . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Résumé du contenu de la page N° 6
Introduction The unobtrusive, low-profile design of the HD4U/X CCTV Camera is ideal for indoor and outdoor installations in commercial and residential venues. Before You Begin Please read this guide carefully before you install the HD4U/X CCTV Camera. Keep this guide for future reference. Unpack Everything Check that the items received match those listed on the order form and packing slip. The HD4U/X packing box should include, in addition to this User Guide: � One fully-assembled HD4U/X camer
Résumé du contenu de la page N° 7
Equipment Required You will require the following tools to complete the installation: � Phillips screwdriver � Tools supplied in the hardware kit (three Allen keys: one each for the security screw on the lid, the conduit plug locking screw, and the lens locking screw) �Side-cutters Document 800-00031 Rev A 7 04/08
Résumé du contenu de la page N° 8
Installation The HD4U/X is weather-sealed for indoor or outdoor locations. The HD4U/X is a fully-integrated enclosure with camera and lens. The wiring can be completely concealed to reduce the risk of tampering. HD4U/X dome enclosure Mounting the Camera The HD4U/X Camera is designed to be surface mounted on a wall or ceiling. Before you mount the camera, use the mounting template provided to mark and pre-drill the holes. 8
Résumé du contenu de la page N° 9
Connecting Cables Through the Housing Base For installations that require pulling cables through the grommet located in the bottom of the base: 1. Use a sharp knife to cut an ! opening in the base gasket (see Figure 1). Be careful. The opening should be only big enough to feed the cable assembly through. 2. Pull the cabling through the opening. 3. Apply appropriate sealant around the opening to prevent moisture from entering the housing. Figure 1 Cable Connection Through Grommet ! Base gasket
Résumé du contenu de la page N° 10
Connecting Cables Through the Side Conduit 1. Peel back the bottom flat gasket below the side conduit just enough to expose the security screw. 2. Use the supplied Allen key to loosen and remove the security screw (see Figure 2). 3. Use a flat screwdriver to unscrew the conduit plug. 4. Pull the cables through the hole. 5. Apply appropriate sealant around the opening to prevent moisture from entering the housing. Figure 2 Cable Connection Through Side Conduit side conduit security screw Allen
Résumé du contenu de la page N° 11
Electrical Box Installations Figure 3 illustrates how to mount the HD4U/X directly to a 4S electrical box or directly to wall or ceiling. For 4S electrical box installations, you can use the supplied adapter plate to cover ceiling or wall imperfections around the electrical box opening. Figure 3 4S Electrical Box Installation Electrical box (not supplied) Ceiling/wall Secure the adapter Adapter plate plate to the 4S (use is optional) electrical box using appropriate screws (not supplied
Résumé du contenu de la page N° 12
Figure 4 illustrates how to mount the HD4U/X directly to a double gang or single gang electrical box. Figure 4 Double Gang/Single Gang Electrical Box Installation (Single Gang Shown) Electrical box (not supplied) Ceiling/wall HD4U/X base Secure the HD4U/X base with screws appropriate to your installation (not supplied) For surface mount installations (without an electrical box), use #6-1 7/16 inch slotted Type A screws (x4) supplied 12
Résumé du contenu de la page N° 13
Connecting the Wiring Follow Figure 5 to connect the video and power wires. Figure 5 Wiring Connection Video: female BNC Power Note For secure installations, Red+ surface-mounted cables should Black – be protected by plastic or metal cable covers. Adjusting the Camera To adjust the HD4U/X Camera: 1. Apply 12 VDC or 24 VAC power to the camera and monitor the video signal. 2. Loosen the screws that lock the gimbal assembly in place (see Figure 6). 3. Adjust the camera carrier to the desired vie
Résumé du contenu de la page N° 14
Figure 6 Gimbal Adjustment Top view Angle view Locking screw. Loosen to Setscrews (x2). Loosen to Locking Joystick (5 way) See adjust Horizontal (B). adjust Pan (C). Other setscrew screw Camera Functions. located on opposite side. B C Legend Set focal length Set focus (bottom) (top) A A = Tilt rotation B = Horizontal rotation C = Pan rotation Adjusting the Lens Focus Lenses are pre-focused at the factory but may require a final adjustment after installation because the optical effect of th
Résumé du contenu de la page N° 15
! $ # " Camera Setup Camera Functions - Press down on the joystick and hold two seconds to access the MAIN MENU. Joystick - Press down to enter a screen or select a menu control option. (5 way) #, $ Move horizontally to and between menus and options !," Move vertically to and between menus and options “…” indicates submenus MENU CAMERA SETUP .. To leave the screen and return to the previous menu, VIEWING .. select PREVIOUS PAGE, and then press down on Move the Select a menu, WDR PRES
Résumé du contenu de la page N° 16
Configuring the WDR Presets Select the appropriate camera mode for the lighting conditions. MENU WDR PRESETS WDR (Wide Dynamic Range) PRESETS INDOOR > MENU WDR PRESETS LOADING DOCK CAMERA SETUP .. GAMING VIEWING .. >PRESETS .. LICENSE PLATE >WDR PRESETS .. INDOOR> FLUORESCENT OFF OUTDOOR DAY/NIGHT SETUP .. PREVIOUS PAGE CUSTOM VERSION .. ATM RESTORE DEFAULTS LOBBY EXIT SAVE & EXIT The table below explains the Preset options on the WDR PRESETS menu. Double-click a Preset to disp
Résumé du contenu de la page N° 17
The AES (Automatic Electronic Shutter) feature compensates for excessive light levels by automatically adjusting the shutter speed of the camera. Select from: HIGHLIGHTS for optimum exposure of bright areas of the scene. SHADOWS for optimum exposure of dark areas of the scene. Optimizing the Camera Setup Note This menu is for advanced users only. The table below explains the options on the CAMERA SETUP menu. Each selection on this menu takes you to a separate screen (see description belo
Résumé du contenu de la page N° 18
>SYNC Synchronize the vertical interval sync pulse of your camera with other equipment to reduce the effect of picture roll on the monitor. Select either: LINE LOCK (default) for cameras using DC power or when line lock is not required, V PHASE > ! 0519624 or PREVIOUS PAGE . to open the Line Lock screen where you can adjust the Vertical Phase (V PHASE) from 0 to 624 (519 is the default). >AGC Automatic Gain Control. This setting affects the day/night threshold. A hi
Résumé du contenu de la page N° 19
Automatic Tracking White Balance (Extended Range). Continuously monitors the color temperature while an internal micro controller sets the white balance. Select this mode when the scene illumination varies between indoor scenes and outdoor scene lighting. Operating color temperature range is 2000K to 11000K. >ADVANCED Opens the ADVANCED WHITE BALANCE menu where you can adjust the magenta or WHITE BAL .. the white balance bias. Options are: . Select ADVANCED WHITE BALAN
Résumé du contenu de la page N° 20
>FLIP Select either: to reverse the image horizontally on the video monitor, or (default) > ID DISPLAY. Select ON to open the CAMERA ID SETUP screen where you can add a CAMERA ID (title) of up to 8 characters. CAMERA ID SETUP Move the cursor (>) to CAMERA ID, then press down on the joystick. The first CAMERA ID ID POSITION UP-LEFT > character appears. Press #, or $ to change the character, then press down on the PREVIOUS PAGE . joystick to move to the next character. When yo
