Résumé du contenu de la page N° 1
®
SD5BCBW Series
Spectra II™
Color/Black & White
Dome Systems
Operation and
Programming Manual
C2423M (5/00)
Pelco • 3500 Pelco Way • Clovis, CA 93612-5699 USA • www.pelco.com
In North America and Canada: Tel (800) 289-9100 • FAX (800) 289-9150
International Customers: Tel +1(559) 292-1981 • FAX +1(559) 348-1120
Résumé du contenu de la page N° 2
CONTENTS Section Page IMPORTANT SAFEGUARDS AND WARNINGS................................................................3 OPERATION ......................................................................................................................4 POWER-UP DISPLAY ...............................................................................................4 OPERATING YOUR SPECTRA II COLOR/BLACK & WHITE DOME ........................4 OPERATING NOTES ....................................
Résumé du contenu de la page N° 3
IMPORTANT SAFEGUARDS AND WARNINGS Prior to installation and use of this product, the following WARNINGS should be observed. 1. Installation and servicing should only be done by qualified service personnel and conform to all local codes. 2. Unless the unit is specifically marked as a NEMA Type 3, 3R, 3S, 4, 4X, 6, or 6P enclosure, it is designed for indoor use only and it must not be installed where exposed to rain and moisture. 3. Only use replacement parts recommended by Pelco. 4. A
Résumé du contenu de la page N° 4
OPERATION POWER-UP DISPLAY When the Spectra II™ dome is powered up, the selected protocol, revision number, and other information is displayed on the monitor. For example, the screen might show the following information: The information displayed depends on the selected protocol (C, D, or P) and the menu selection for power- PELCO SPECT II 4.0 up mode. (Refer to the Power-Up Mode in the CONFIGURE DONE Programming section). Protocol C The information remains on the monitor until the do
Résumé du contenu de la page N° 5
OPERATING NOTES PAN AND TILT FUNCTIONS Controller Type Pan Tilt Fixed speed Speed determined by controller Speed determined by controller Variable speed 0.1 to 80° per second, depending on joystick position 0.1 to 40° per second, depending on joystick position Turbo Mode 150° per second 200° per second Preset Mode 250° per second Does not affect the tilt speed If the proportional pan mode is enabled (refer to Proportional Pan in the Programming section), the pan and tilt speeds will depe
Résumé du contenu de la page N° 6
PATTERNS The Spectra II dome can do either one full pattern (1.5, 3, or 6 minutes long) or two half NOTE: The dome cannot patterns (.75, 1.5, or 3 minutes long). This pattern can consist of any standard pan and tilt do electronic zoom in a or lens command. Presets, flip, and turbo are not allowed in a pattern. Zone scan can be pattern. Optical zoom will enabled while running a pattern. operate in a pattern. Refer to the documentation for your control system to program and run patterns.
Résumé du contenu de la page N° 7
AUXILIARY OUTPUTS An AUX 1 command from the controller will activate the relay in the dome and operate the device that is connected to the relay. The relay will remain latched until a clear command is issued. An AUX 2 command from the controller will place a ground at the output of AUX 2 to operate the device that is connected to it. The output will remain latched until a clear command is issued. The output relay can also be programmed so that it is activated when any alarm input is acti
Résumé du contenu de la page N° 8
PROGRAMMING Programming Guide - Spectra II Color/Black & White Gain/AGC Menu 1. Access main menu (preset 95). 2. Make main menu selections. Joystick: Move up or down to position cursor or to toggle between selections. AGC mode Auto Iris Open: Enter Gain 6 Camera Menu Iris Close: Cancel Exit Backlight comp Off Zoom limit x72 Reset camera Auto-Iris Menu IR Filter Menu Exit Auto-iris mode Auto IR Filter mode Auto Line Sync Menu Auto-iris level 7
Résumé du contenu de la page N° 9
ACCESSING MAIN MENU (PRESET 95) You can call up the main menu on your monitor by programming (setting or creating) preset NOTE: For American 95 (28 if in 32-preset mode). Dynamics controllers with only 32 presets, set switch Programming preset 95 for Pelco’s controllers varies according to the type of controller you SW1-7 on the dome drive in are using. Instructions for programming preset 95 are given below for various Pelco the ON position. When controllers. SW1-7 is ON, preset CM67
Résumé du contenu de la page N° 10
ALARMS The Spectra II dome has seven alarm inputs, which can be designated as either high or low priority. The high priority setting is significant when more than one alarm is activated. If priority in alarms is not required, leave all alarms in the low setting. Refer to the Alarm Priority section. If presets 1-7 are not used for alarms, they can be used as regular presets. However, if they are being used for alarms, they should not be used for anything else. Also refer to the Alarm Dwell,
Résumé du contenu de la page N° 11
NOTE: The Spectra II 6. Position the cursor (>) beside the number of the alarm input for which you want to set the pattern. Color/Black and White 7. Press the Iris Open button. The cursor moves to the right, beside the words Full Pat, camera cannot do electronic Half Pat 1, Half Pat 2, or No Pattern. zoom in a pattern. Optical 8. Move the joystick up or down to toggle between the choices. zoom will operate in a 9. SELECT - Press the Iris Open button on your keyboard to select your c
Résumé du contenu de la page N° 12
AUTO FLIP Main Menu Other Menu Auto flip On Proportional pan On Limit stops Off Park time minutes 0 Scan speed deg/s 25 Pattern length 1.5 min EXIT Exit There are two auto flip modes: On - Auto flip mode is enabled. Off - Auto flip mode is disabled. To change the auto flip mode: 1. Program preset 95 (28). The main menu appears. 2. Position the cursor (>) beside Other. 3. Press the Iris Open button to enter the O
Résumé du contenu de la page N° 13
AUTO IRIS Main Menu Camera Menu Auto-Iris Menu Backlight comp Off Zoom limit x72 Auto-iris mode Auto Reset camera Auto-iris level 7 Exit EXIT Exit The following are the settings for auto iris: Mode Level To change the settings for auto iris: 1. Program preset 95 (28). The main menu appears. 2. Position the cursor (>) beside Camera. 3. Press the Iris Open button to enter the Camera m
Résumé du contenu de la page N° 14
AUTO IR LEVEL Main Menu Camera Menu Next Menu IR Filter Menu Slow shutter mode Auto Backlight comp Off Shutter speed Auto Zoom limit x72 Auto focus mode Auto Reset camera IR Filter mode Auto Auto IR Level Dusk Exit Previous EXIT Exit Exit The IR level setting determines when the IR filter will switch IN or OUT. Following are the available sett
Résumé du contenu de la page N° 15
4. Move the joystick up or down to position the cursor next to either Aux 1 mode or Aux 2 mode. 5. Press the Iris Open button. The cursor moves to the right, beside the word Normal, Latching, or Alarm. 6. Move the joystick up or down to toggle between Normal, Latching, or Alarm. 7. SELECT - Press the Iris Open button on your keyboard to select your choice. CANCEL - Press the Iris Close button if you do not want to change the setting. BACKLIGHT COMPENSATION Main Menu Camera Menu
Résumé du contenu de la page N° 16
GAIN/AGC Main Menu Camera Menu Gain/AGC Menu Backlight comp Off Zoom limit x72 Reset camera AGC mode Auto Gain 6 Exit EXIT Exit Gain - The amount of amplification the camera places on its video information in order to obtain a full 1-volt peak-to-peak video signal out. AGC - Automatic Gain Control. AGC MODE There are two AGC settings : Auto Mode - Automatically adjusts the gain. Off Mo
Résumé du contenu de la page N° 17
IR FILTER MODE Main Menu Camera Menu Next Menu IR Filter Menu Slow shutter mode Auto Backlight comp Off Shutter speed Auto Zoom limit x72 Auto focus mode Auto Reset camera IR Filter mode Auto Auto IR Level Dusk Exit Previous EXIT Exit Exit There are two settings for the IR filter mode: Auto - IR filter switches in and out automatically. Do the
Résumé du contenu de la page N° 18
TURNING LIMIT STOPS ON OR OFF To change the limit stop mode: 1. Program preset 95 (28). The main menu appears. 2. Position the cursor (>) beside Other. 3. Press the Iris Open button to enter the Other menu. 4. Position the cursor (>) beside Limit Stops. 5. Press the Iris Open button. The cursor moves to the right, beside the word On or Off. 6. Move the joystick up or down to toggle between On and Off. 7. SELECT - Press the Iris Open button on your keyboard to select your choice.
Résumé du contenu de la page N° 19
LINE SYNC PHASE - The cursor moves to a numeric value. Move the joystick up or down to change the value. Press the Iris Open button to select the choice. The value represents the phase angle in tenths of a degree between 0 degrees and 359 degrees. For example, 900 is 90 degrees, 1200 is 120 degrees, and 2400 is 240 degrees. Press the Iris Open button on your keyboard to select your choice. The Line Sync setting will change to ON. The camera may reset or the picture on your monitor may wiggl
Résumé du contenu de la page N° 20
POWER-UP MODE Main Menu Power-Up Menu Power Up Default Exit EXIT This feature lets the dome resume a desired condition following power-up. The menu includes the following choices. Default - On power-up, the dome goes through a configuration cycle and stops at zero reference, showing “Configuration Done,” address, and mode settings on the screen. Park - The dome moves to preset 1 when the power-up sequence finishes.
