Instruction d'utilisation Pelco HS4514-2

Résumé du contenu de la page N° 1

C1472M-C (10/05)
HS4514 Series
High Security Enclosure
®
3500 Pelco Way
IMPORTANT SAFEGUARDS AND WARNINGS
Clovis, CA 93612-5699
Prior to installation and use of this product, the following WARNINGS should be observed.
USA
In North America & Canada: 1. Installation and servicing should only be done by qualified service personnel and conform
Tel (800) 289-9100
to all local codes.
FAX (800) 289-9150
2. Only use replacement parts recommended by Pelco.
International Customers:
Tel (1-559) 292-1981
3.

Résumé du contenu de la page N° 2

INSTALLATION The following items are supplied: 1 HS4514 Series enclosure 1 #10 socket for tamper-resistant screws (1/4-inch drive tool not provided) 1 Three-pin plug with leads (included with heater -1/-2/-3 models) 2 1/4-20 Phillips head screws (to mount enclosure) 1 Steel eyebolt Enclosure Mounting 1. Place the enclosure on a flat surface with the top facing up. Open the enclosure using the following procedure: a. Remove the four tamper-resistant screws securing the enclosure cover using the #

Résumé du contenu de la page N° 3

Enclosure Power If the enclosure does not have a heater (model HS4514), proceed to the Camera Mounting section. If your enclosure has a heater (models HS4514-1/-2/-3), follow the steps below. 1. Add the camera’s wattage to the wattage of the heater. Refer to the Specifications section, for the heater wattage. 2. Determine the size of wire to use. If you are using 24 VAC, refer to Table A. 3. Bring wires for AC high, AC neutral, and ground into the enclosure. Refer to Figure 1, HS4514 Series Inpu

Résumé du contenu de la page N° 4

Figure 1. HS4514 Series Input Wiring Diagram 4 Pelco Manual C1472M-C (10/05) ACCESSORY: HK4514-1,HK4514-2 ACCESSORY: BK4514-2 HEATER ACCESSORY: BK4514-1 RED RED FAN 24V/120V BK4514-3 24 VDC HEATER WHT WHT FAN RED 24V/120V 120/230 V BLK ACCESSORY: HK4514-3 PCB9000277ASSY HEATER HEATER WHT 230V 230V RED BLK PC05-0003-00A0 PA05-0003- TH1 FAN PELCO LENS CONTROL 1 P1 INPUTS LENS CAM1 P2 5 1 J1 PLUG PLUG TB2 TB1 PLUG 1 23 123 1 2 3 4 5 6 7 8 9 10 HI NT GND 1 2 OPTIONAL CAMERA PELCO POWER LENS LENS

Résumé du contenu de la page N° 5

PA05-0003- TH1 FAN PELCO LENS CONTROL 1 P1 INPUTS LENS CAM1 P2 5 1 J1 TB1 TB2 1 2 3 4 5 6 7 8 9 10 HI NT GND Figure 2. Circuit Board Component Locations Table B. Video Coaxial Cable Wiring Distances Cable Type* Maximum Distance RG59/U 750 ft (229 m) RG6/U 1,000 ft (305 m) RG11/U 1,500 ft (457 m) *Minimum cable requirements: 75 ohms impedance All-copper center conductor All-copper braided shield with 95% braid coverage Camera Mounting 1. Attach the camera to the sled with the 1/4-20 Phillips-hea

Résumé du contenu de la page N° 6

b. Wire the lens controller to the 10-connector INPUTS terminal on the circuit board as follows: Lens Common Connector 1 Preset Common Connector 5 Focus Connector 2 Preset Focus Connector 6 Zoom Connector 3 Preset Zoom Connector 7 Iris Connector 4 Preset High Connector 8 Proceed to the Wiring Camera to Power section. Wiring Camera to Power HS4514 Model Only Bring the camera wiring into the enclosure. If you are using 24 VAC refer to Table A, 24 VAC Wiring Distances, to determine the size of wire

Résumé du contenu de la page N° 7

TROUBLESHOOTING If you need to troubleshoot the circuit board or wiring, refer to Figure 1, HS4514 Series Input Wiring Diagram, and Figure 2, Circuit Board Component Locations. After the enclosure is mounted, opening the enclosure is more convenient using the following procedure: 1. Remove the two tamper-resistant screws securing the front of the enclosure cover. 2. Loosen, but do not remove, the two tamper-resistant screws securing the rear of the enclosure cover. 3. Push the top of the enclosu

Résumé du contenu de la page N° 8

GENERAL Construction Body: 0.134-inch thick steel Viewing Window: 1.25-inch (31.75 mm) thick, optically clear, bullet-resistant, MR5 ® coated, Lexgard (UL 752, Level 3 [.44 Mag.] rated) Viewing Window Area: 3.44 in. H x 4.75 in. W (8.74 x 12.07 cm) Finish: Gray polyester powder coat Ratings: Meets IP 55 and NEMA Type 3 standards Environment: Indoor/outdoor; -10° to 100°F (-23° to 38°C) Dimensions: 20.07 in. L x 6.32 in. W x 6.13 in. H (50.98 x 16.05 x 15.57 cm) Weight: 27 lb (12.25 kg) (Design a