Résumé du contenu de la page N° 1
Contents
Safety Information and Introduction ............2
AV RECEIVER
Table of Contents...........................................6
TX-NR727
Connections .................................................12
Turning On & Basic Operations..................21
Playback........................................................29
Instruction Manual
Advanced Operations ..................................52
Controlling Other Components...................76
Appendix...........................................
Résumé du contenu de la page N° 2
Safety Information and Introduction 9. Do not defeat the safety purpose of the polarized B. If liquid has been spilled, or objects have fallen or grounding-type plug. A polarized plug has two into the apparatus, WARNING: blades with one wider than the other. A grounding C. If the apparatus has been exposed to rain or TO REDUCE THE RISK OF FIRE OR ELECTRIC type plug has two blades and a third grounding water, SHOCK, DO NOT EXPOSE THIS APPARATUS TO RAIN prong. The wide blade or the third prong
Résumé du contenu de la page N° 3
Safety Information and Introduction extended period, remove the power cord from the interference in a residential installation. This Precautions AC outlet. equipment generates, uses and can radiate radio 5. Preventing Hearing Loss frequency energy and, if not installed and used in 1. Recording Copyright—Unless it’s for personal Caution accordance with the instructions, may cause harmful use only, recording copyrighted material is illegal Excessive sound pressure from earphones and interfer
Résumé du contenu de la page N° 4
Safety Information and Introduction RF Exposure Compliance Modèle pour les Canadien IMPORTANT This equipment complies with FCC/IC radiation The plug is fitted with an appropriate fuse. If the fuse REMARQUE: CET APPAREIL NUMÉRIQUE DE exposure limits set forth for an uncontrolled needs to be replaced, the replacement fuse must LA CLASSE B EST CONFORME À LA NORME environment and meets the FCC radio frequency approved by ASTA or BSI to BS1362 and have the NMB-003 DU CANADA. (RF) Exposure Guidel
Résumé du contenu de la page N° 5
Safety Information and Introduction –Hiermit erklärt Onkyo Corporation, dass sich das essentiële eisen en de andere relevante bepalin- 23764/SDPPI/2012 Complies with 2371 Gerät TX-NR727 in Übereinstimmung mit den gen van richtlijn 1999/5/EG. IDA Standards DA106032 grundlegenden Anforderungen und den übrigen –Niniejszym Onkyo Corporation deklaruje że einschlägigen Bestimmungen der Richtlinie TX-NR727 jest zgodny z zasadniczymi TA-20120424004 1999/5/EG befindet. TRA wymaganiami i innymi w ła ś
Résumé du contenu de la page N° 6
Safety Information and Introduction Initial Setup .................................................................22 Table of Contents Selecting the Language Advanced Operations for the On-screen Setup Menus .............................22 Audyssey MultEQ: Auto Setup .................................22 On-screen Setup......................................................... 52 Source Connection ...................................................23 Safety Information and Introduction Using the
Résumé du contenu de la page N° 7
Safety Information and Introduction Connections Features 8 HDMI Inputs (1 on front panel) and 2 Outputs Amplifier * 4K (up-scaling and Passthrough )-compatible HDMI Inputs 110 Watts/Channel @ 8 ohms (FTC) * Compatible with HDMI IN 1 to HDMI IN 4 only 170 Watts/Channel @ 6 ohms (IEC) Onkyo for System Control 185 Watts/Channel @ 6 ohms (JEITA) 3 Digital Inputs (1 Optical/2 Coaxial) WRAT–Wide Range Amplifier Technology Component Video Switching (1 Input/1 Output) (5 Hz to 100
Résumé du contenu de la page N° 8
Safety Information and Introduction Front & Rear Panels Front Panel (North American and Taiwanese models) (European, Australian and Asian models) For detailed information, see the pages in MEMORY button (38) Input selector buttons (29) parentheses. TUNING MODE button (38) DISPLAY button (49) ON/STANDBY button (21) HOME button (51) USB port (32) MUSIC OPTIMIZER button (North American TUNING / (38), PRESET / (38), cursor SETUP MIC jack (25) and Taiwa
Résumé du contenu de la page N° 9
Safety Information and Introduction Display s For detailed information, see the pages in Tuning indicators SLEEP indicator (49) parentheses. RDS indicator (excluding North American and Channel/Unit indicators Z2 (Zone 2) indicator (75) Taiwanese models) (39) ch indicator AUTO indicator (38) Z3 (Zone 3) indicator (75) Hz indicator TUNED indicator (38) 3D indicator m/ft indicator FM STEREO indicator (38) This lights when a 3D input signal is detected. dB indicator
Résumé du contenu de la page N° 10
Safety Information and Introduction Rear Panel (North American, Australian and Asian models) (European and Taiwanese models) See “Connecting Your Speakers” for connection Power cord (North American, Australian and (➔ pages 12 to 20). Asian models) REMOTE CONTROL jack DIGITAL IN COAXIAL and OPTICAL jacks COMPONENT VIDEO IN and OUT jacks GND screw ETHERNET port Composite video and analog audio jacks FM ANTENNA jack and AM ANTENNA terminal (BD/DVD IN, CBL/SAT IN, STB/D
Résumé du contenu de la page N° 11
Safety Information and Introduction For detailed information, see the pages in ■ Aiming the remote controller Remote Controller parentheses. To use the remote controller, point it at the AV receiver’s remote control sensor, as shown below. RECEIVER button (21) Controlling the AV Receiver REMOTE MODE/INPUT SELECTOR buttons Remote control sensor (29) To control the AV receiver, press RECEIVER to AV receiver select Receiver mode. // / and ENTER buttons Q S
Résumé du contenu de la page N° 12
Connections To find the best position for your subwoofer, while Speaker Configuration playing a movie or some music with good bass, The following table indicates the channels you should experiment by placing your subwoofer at various use depending on the number of speakers that you positions within the room, and choose the one that have. provides the most satisfying results. No matter how many speakers you use, a powered Connections You can connec
Résumé du contenu de la page N° 13
Connections Connecting the Speaker Cables/Powered Subwoofers Before connecting the power cord, connect all of your speakers and AV components. A setup wizard Please connect , , , , and for 5.1-channel surround. is launched upon first-time use to let you perform If you’re using only one surround back the settings. Front Front speaker, connect it to the SURROUND speaker R speaker L BACK or FRONT HIGH L terminals. Read the instructions supplied with your speakers. By
Résumé du contenu de la page N° 14
Connections ■ Speaker Connection Precautions Bi-amping the Front Speakers Using Dipole Speakers You can connect speakers with an impedance of between 4 and 16 ohms. If the impedance of any of Important: the connected speakers is 4 ohms or more, but less When making the bi-amping connections, be sure to than 6 ohms, be sure to set the minimum speaker TV/screen remove the jumper bars that link the speakers’ tweeter impedance to “4ohms” (➔ page 59). If you use (high) and woofer (low) ter
Résumé du contenu de la page N° 15
Connections Use this jack to connect to the set top box/digital Connecting the TV/AV components video recorder, etc. Use this jack to connect to the game consoles, Before connecting the power cord, connect all of your speakers and AV components. To display the setup etc. menu on the TV screen, connecting the TV to HDMI OUT MAIN is required. Use this port to connect to a LAN port on a router so the AV receiver can be connected to your home network. Use jack and termi
Résumé du contenu de la page N° 16
Connections ■ MHL (Mobile High-Definition Link) Internet radio With its support for MHL (Mobile High-Definition Link), The AV receiver allows interoperability of the CEC the AUX (Front) input allows you to deliver high- (Consumer Electronics Control) specified in the HDMI Router WAN definition video from a connected mobile device. Modem standard, which is known as RIHD. Various linked LAN operations can be performed by connecting the AV receiver to an RIHD-compatible TV, player, or r
Résumé du contenu de la page N° 17
Connections On the TV, when you select anything other than the HDMI Operations that can be performed with Confirm the settings jack to which the AV receiver is connected, the input on the RIHD connection AV receiver will be switched to “TV/CD”. 1. Turn on the power for all connected components. The AV receiver will automatically power on in conjunction 2. Turn off the power of the TV, and confirm that the ■ For -compatible TV when it determines it to be necessary. Even if the A
Résumé du contenu de la page N° 18
Connections *2 This is possible when “Audio Return Channel” is set to Signal Selection Example Video Signal Flow Chart “Auto” (➔ page 71), the TV/CD input selector is Blu-ray Disc/DVD player, etc. Blu-ray Disc/DVD player, etc. selected, and your TV is ARC capable. Tip Composite Component HDMI Composite Component HDMI IN When a signal is input via HDMI and the corresponding IN input selector is selected, the HDMI indicator lights. In the AV receiver AV receiver case of an optical or coaxial
Résumé du contenu de la page N° 19
Connections ■ Coaxial digital audio Connecting the Antennas Coaxial digital connections allow you to enjoy digital *1 sound such as PCM , Dolby Digital or DTS. The This section explains how to connect the supplied indoor FM antenna and AM loop antenna. audio quality is the same as optical. The AV receiver won’t pick up any radio signals without any antenna connected, so you must connect the antenna to use the tuner. Orange ■ Analog audio (RCA) (North American and (European, Australian Analo
Résumé du contenu de la page N° 20
Connections Connecting Onkyo RI Components Using Headphones Make sure that each Onkyo component is Connect a pair of stereo headphones with a 1 1 connected with an analog audio cable standard plug (1/4 inch or ø 6.3 mm) to the (connection in the hookup examples) PHONES jack. (➔ page 15). While the headphones plug is inserted in the Make the connection (see the illustration). PHONES jack, indicator lights. 2 Note If you’re using an RI Dock, or cassette tape 3 Always turn d
