Résumé du contenu de la page N° 1
User’s Manual
DVI DL 101
Extron Electronics, USA Extron Electronics, Europe Extron Electronics, Asia Extron Electronics, Japan
1230 South Lewis Street Beeldschermweg 6C 135 Joo Seng Rd. #04-01 Kyodo Building, 16 Ichibancho
Dual Length DVI Cable Equalizer
Anaheim, CA 92805 3821 AH Amersfoort, The Netherlands PM Industrial Bldg., Singapore 368363 Chiyoda-ku, Tokyo 102-0082
800.633.9876 714.491.1500 +800.3987.6673 +31.33.453.4040 +800.7339.8766 +65.6383.4400 Japan
FAX 714.491.1517 FAX +31.3
Résumé du contenu de la page N° 2
Precautions Safety Instructions • English Warning Extron’s Warranty Power sources • This equipment should be operated only from the power source This symbol is intended to alert the user of important indicated on the product. This equipment is intended to be used with a main power operating and maintenance (servicing) instructions in system with a grounded (neutral) conductor. The third (grounding) pin is a safety Extron Electronics warrants this product against defects in materials and wo
Résumé du contenu de la page N° 3
警告 安全须知 • 中文 电源 • 该设备只能使用产品上标明的电源。 设备 这个符号提示用户该设备用户手册中 必须使用有地线的供电系统供电。 第三条线 有重要的操作和维护说明。 （地线）是安全设施，不能不用或跳过。 拔掉电源 • 为安全地从设备拔掉电源，请拔掉所有设备后 这个符号警告用户该设备机壳内有暴 或桌面电源的电源线，或任何接到市电系统的电源线。 电源线保护 • 妥善布线， 避免被踩踏，或重物挤压。 露的危险电压，有触电危险。 维护 • 所有维修必须由认证的维修人员进行。 设备内部没 注意 有用户可以更换的零件。为避免出现触电危险不要自己 阅读说明书 • 用户使用该设备前必须阅读并理 试图打开设备盖子维修该设备。 解所有安全和使用说明。 通风孔 • 有些设备机壳上有通风槽或孔，它们是用来防止 保存说明书 • 用户应保存安全说明书以备将来使 机内敏感元件过热。 不要用任何东西挡住通风孔。 用。 锂电池 • 不正确的更换电池会有爆炸的危险。 必须使用与 遵守警告 • 用户应遵守产品和用户指南上的所有安 厂家推荐的相同或相近型号的电池。 按照生产厂的建 全和操作说明。 议处理废弃电
Résumé du contenu de la page N° 4
Table of Contents Chapter One • Introduction .................................................... 1-1 About this Manual .................................................................... 1-2 About the DVI DL 101 Cable Equalizer ............................... 1-2 Featur es ........................................................................................ 1-2 Application Diagrams ............................................................... 1-3 Chapter Two • Installation and Oper
Résumé du contenu de la page N° 5
Table of Contents, cont’d DVI DL 101 Chapter One 1 Introduction About this Manual About the DVI DL 101 Cable Equalizer Features Application Diagram ii DVI DL 101 • Table of Contents
Résumé du contenu de la page N° 6
Introduction • DVI output — One female DVI-I connector supports DVI-D About this Manual output. This manual contains information about the Extron DVI DL 101 The acceptable output cable length is 16.4' (5 m). Dual Link Cable Equalizer and describes how to connect and operate it. The terms "DVI DL" and "equalizer" are used Dual link DVI cables must be used for dual link DVI N interchangeably throughout this manual to refer to the product. signals. With a single link DVI cable, only sing
Résumé du contenu de la page N° 7
Introduction, cont’d DVI DL 101 Chapter Two 2 Installation and Operation Mounting the DVI DL 101 Front and Back Panel Features and Connections Enabling the DDC Buffer 1-4 DVI DL 101 • Intr oduction
Résumé du contenu de la page N° 8
Installation and Operation 5. Reliable earthing (grounding) — Maintain reliable Mounting the DVI DL 101 grounding of rack-mounted equipment. Pay particular The DVI DL can be mounted on a rack shelf, under or through attention to supply connections other than direct furniture, attached to a projector pole, or placed on a table top. connections to the branch circuit (such as the use of power strips). Tabletop use Rack mounting procedure Four self-adhesive rubber feet are included with th
Résumé du contenu de la page N° 9
Installation and Operation, cont’d VersaTools Rack Shelf 1/4 Rack Width Front False Faceplate Use 2 mounting holes on opposite corners. (2) 4-40 x 3/16" Under-furniture mounting the DVI DL Screws Mounting the DVI DL 101 on a 3.5” deep rack shelf 6. Drill 3/32" (2 mm) diameter pilot holes, 1/4" (6.3 mm) deep in the mounting surface at the marked screw locations. Under-furniture mounting 7. Insert #8 wood screws into the four pilot holes. Tighten The DVI DL can be mounted under a horizo
Résumé du contenu de la page N° 10
Installation and Operation, cont’d PMK 300 mounting Mount the DVI DL to a PMK 300 bracket as follows: 1. If necessary, remove the feet from the bottom of the unit. 2. Mount the receiver to one of the bracket’s three mounting plates using two of the supplied 4-40 x 3/16" screws in opposite (diagonal) corners to secure the device to the bracket. It can be vertically mounted facing either up or down (see the illustration below). On the side mounting plates, the device is typically N mounted
Résumé du contenu de la page N° 11
Installation and Operation, cont’d 6. Secure the bracket to the U-bolt with the included hex nuts, washers, and lock washers. Tighten the hex nuts just Contoured enough that they can be loosened by hand. Bracket Base PMK 350 mounting Extron Mount the DVI DL to a PMK 350 bracket as follows: DVI DL 101 1. Remove the front and rear plates from the PMK 350, using Equalizer an Extron Tweeker or a #2 Philips screwdriver. Retain the screws to reattach the plates when you are finished. Power Sup
Résumé du contenu de la page N° 12
Installation and Operation, cont’d 7. Assemble the U-bolt and the following parts in the Front and Back Panel Features and Connections following order (see the illustration below): 2 a. Pass the legs of the U-bolt through the slotted holes on the mount plate flange. DVI-DUAL LINK INPUT b. Place the legs around the projector pole. 1 c. Pass the legs through the holes in the contour base. DVI DL 101 The pole fits snugly into the depression in the N center of the contoured base. d. Pass the le
Résumé du contenu de la page N° 13
Installation and Operation, cont’d 1 8 The table below shows the maximum cable lengths recommended for each resolution, in dual link mode and single link mode. 9 17 24 Avoid using couplers and adapters between cables, as N this can result in signal degradation. Pin Pin Signal Signal Pin Signal 1 TMDS data 2– 9 TMDS data 1– 17 TMDS data 0– Video Single Link Dual Link Resolution Mode Mode 2 TMDS data 2+ 10 TMDS data 1+ 18 TMDS data 0+ 1280x1024 3 TMDS data 11 TMDS data 1 19 TMDS data 0/
Résumé du contenu de la page N° 14
Installation and Operation, cont’d • Incorrect color space selection (purple or blue tint) • Corrupted EDID data (The computer or source cannot read Smooth Ridges the EDID of the connected display correctly due to a long cable run.) SECTION A–A To enable the buffer, 1. Using an Extron Tweeker or other small Philips Power Supply screwdriver, remove the seven screws (three on each side Output Cord Tie Wrap and one on top) that hold the top cover onto the unit. 2. Remove the two jack screws o
Résumé du contenu de la page N° 15
Installation and Operation, cont’d 5. Lift each jumper off its pins and slide it down onto the DVI DL 101 inside and middle pins. See the illustration below. DDC Buffer DDC Buffer Bypassed Enabled (Default) Jumper Pin Sets J4 and J5 Inside Unit Appendix A Slide forward, then up. A Jack Screw Remove screws from Nut sides and top (7). 6. Replace the top cover onto the unit, and slide it back until the DVI input connector protrudes through its slot in the front panel. Specifications, Parts, a
Résumé du contenu de la page N° 16
Specifications, Parts, and Accessories Temperature/humidity ................ Storage: -40 to +158 °F (-40 to +70 °C) / Specifications – DVI DL 10% to 90%, noncondensing *Dual link DVI is backwards compatible with all single link N Operating: +32 to +122 °F (0 to +50 °C) / DVI and HDMI signals. 10% to 90%, noncondensing Cooling ........................................... Convection, no vents Rack mount .................................... Yes, with optional 1U, 9.5" deep rack shelf, Video
Résumé du contenu de la page N° 17
Specifications, Parts, and Accessories, cont’d Included Parts Cables and Adapters These items are included in each order for the DVI DL 101: The following cables and adapters may be purchased for use with the DVI DL 101: Replacement Included parts part number Cable/Adapter Part number DVI DL 101 Multi-Rate Equalizer 60-962-01 IN9700 Series DVI (25', 35', 50', and 75' 26-584-xx lengths) 12 VDC, 2 A external power supply kit 70-055-01 DVID SL Series DVI (3', 6', and 15' lengths) 26-585-xx IEC p
Résumé du contenu de la page N° 18
Specifications, Parts, and Accessories, cont’d This page was intentionally left blank. A-6 DVI DL 101 • Specifications, Pats, and Accesso r ries
