Résumé du contenu de la page N° 1
User Manual
CS-62
Read this guide thoroughly and follow the installation and operation
procedures carefully in order to prevent any damage to the units and/or
any devices that connect to them.
This package contains:
1 CS-62 Two Port Petite KVM Switch with Attached Cables
1 User Manual
1 Quick Start Guide
If anything is damaged or missing, contact your dealer.
®
© Copyright 2003 ATEN International Co., Ltd.
Manual Part No. PAPE - 1232-1AT
Printed in China 06/2003
All brand names and tradema
Résumé du contenu de la page N° 2
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy, and if not installed and used in accordance with the instruction manual, may cause interference to radio communications. However, there is no guarantee that interference
Résumé du contenu de la page N° 3
Overview The CS-62 Petite KVM Switch Switch is a control unit that allows access to two computer systems from a single console (keyboard, monitor, and mouse). Before the development of the CS-62, the only way to control multiple computer configurations from a single console was through a complex and costly network system. Now, with the CS-62 Petite KVM Switch, you can easily access two computers in a cost effective manner. The CS-62 improves on previous models with a 50% smaller desktop footprin
Résumé du contenu de la page N° 4
Features One console controls two computers Compact design features two molded-in KVM (keyboard, video, mouse) cables Supports Microsoft IntelliMouse and the scrolling wheel on most mice Easy to install - No software required - connecting cables to the computers is all it takes Easy to operate - computer selection via hotkeys - auto scan function to monitor computer operation LED display for easy status monitoring Caps Lock, Num Lock, and Scroll Lock states are saved and restored w
Résumé du contenu de la page N° 5
Hardware Requirements Console A VGA, SVGA, or Multisync monitor capable of the highest resolution that you will be using on any computer in the installation A PS/2 Mouse A PS/2 Keyboard Computers The following equipment must be installed on each computer that is to be connected to the system: A VGA, SVGA or Multisync card. A 6-pin mini-DIN (PS/2 style) mouse port. A 6-pin mini-DIN (PS/2 Style) keyboard port. Cables For optimum signal integrity and to simplify the layout, two high- q
Résumé du contenu de la page N° 6
Front View 2 1 3 1. Port LEDs A LED lights to indicate its corresponding port is the one that has the KVM focus. Depending on the port’s status, the LED may flash according to a specific pattern (see the LED Display Table, p. 8, for details). 2. KVM Cables These 3-in-1 cables connect to the keyboard, video, and mouse ports on the computers you are installing. 3. Console Ports Your keyboard, monitor, and mouse plug in here. Each port is marked with an appropriate icon to indicate itself. - 4 - 20
Résumé du contenu de la page N° 7
Installation 1. Before you begin, make sure that power to all the devices you will be connecting up have been turned off. You must unplug the power cords of any computers that have the Keyboard Power On function. Otherwise, the switch will receive power from the computer. 2. To prevent damage to your installation due to ground potential difference, make sure that all devices on the installation are properly grounded. Refer to the Installation diagram on the next page as you perform the followi
Résumé du contenu de la page N° 8
- 6 - 2003-06-20
Résumé du contenu de la page N° 9
Operation The CS-62 Petite KVM Switch uses hotkey combinations to provide KVM focus to the computers. The hotkey combinations allow you to: Select the Active Port Invoke Auto Scan Mode Set the Auto Scan Time Interval Selecting the Active Port You can toggle the KVM focus between the two computers by pressing and releasing the Scroll Lock key twice: [Scroll Lock]+[Scroll Lock]. Auto Scan Mode The CS-62’s Auto Scan feature automatically toggles the KVM focus between the two computers at regu
Résumé du contenu de la page N° 10
Changing the Scan Interval Before you invoke Auto Scan, you can change the amount of time that Auto Scan dwells on each port (the time interval), with the following hotkey combination: [Left shift] [Right shift] [S] [n] Where n represents a number from 1 to 4 that specifies the desired scan interval time, as shown in the table below; n Scan Interval 1 3 secs 2 5 secs 3 10 secs 4 20 secs Note: Press and release the keys one at a time. LED Display Table Activity Indication Off Port is not sele
Résumé du contenu de la page N° 11
Specifications Function Specification Computer Connections 2 Port Selection Hot Keys LEDs Selected 2 Connectors Keyboard 1 x 6 pin mini-DIN female (PS/2 style) - Console 2 x 6 pin mini-DIN male (PS/2 style) - CPU Ports Mouse 1 x 6 pin mini-DIN female (PS/2 style) - Console 2 x 6 pin mini-DIN male (PS/2 style) - CPU Ports Video 1 x HDB-15 female (std. VGA/SVGA) - Console 2 x HDB-15 male (std. VGA/SVGA) - CPU Ports Scan Interval 3, 5, 10, 20 Seconds o Operating Temperature 0 - 50 C o Storage Tempe
Résumé du contenu de la page N° 12
Troubleshooting Symptom Possible Cause Action Keyboard Not Loose cables. Check all keyboard cable connections 1 Responding to make sure they are completely seated in their sockets. Keyboard needs to be Unplug the keyboard from the Console reset. Keyboard Port, then plug it back in. Switch needs to be Turn off the computers. Unplug the reset KVM cables. Wait five seconds; then plug the cables back in and turn the computers on. Switch is in Auto Scan Press the [Spacebar] to exit Auto Scan Mode. Mo
Résumé du contenu de la page N° 13
Symptom Possible Cause Action Mouse Not Switch needs to be Turn off the computers and unplug the Detected, or reset. KVM cables. Wait five seconds; then Does Not plug the cables back in and turn the Respond computers on. 2 Correctly Mouse set to Serial Some mice can be set to act as either Mode. a PS/2 or serial mouse. Make sure the mouse is set to PS/2 mode. Incorrect Mouse Check your Device Manager to be sure Driver. that the correct driver for your mouse (obtained from the manufacturer, or su
Résumé du contenu de la page N° 14
Limited Warranty IN NO EVENT SHALL THE DIRECT VENDOR’S LIABILITY EXCEED THE PRICE PAID FOR THE PRODUCT FROM THE DIRECT, INDIRECT, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES RESULTING FROM THE USE OF THE PRODUCT, DISK OR ITS DOCUMENTATION. The direct vendor makes no warranty or representation, expressed, implied, or statutory with respect to the contents or use of this documentation, and specially disclaims its quality, performance, merchantability, or fitness for any particular purpose. The di
Résumé du contenu de la page N° 15
Notes: - 13 - 2003-06-20
Résumé du contenu de la page N° 16
Notes: - 14 - 2003-06-20
