Instruction d'utilisation Clarion SIRIUS DSC920S

Résumé du contenu de la page N° 1

Owner’s manual
Mode d’emploi
Manual de instrucciones
DSC920S
SIRIUS SATELLITE RADIO
RECEIVER CONTROLLER
CONTRÔLEUR DE RÉCEPTEUR
RADIO SATELLITE SIRIUS
CONTROLADOR DEL
SINTONIZADOR SIRIUS DE
RECEPCIÓN RADIO VÍA
SATÉLITE

Résumé du contenu de la page N° 2

English Thank you for purchasing this Clarion DSC920S. * Please read this owner’s manual in its entirety before operating this equipment. * After reading this manual, be sure to keep it in a handy place (e.g., glove compartment). * Check the contents of the enclosed warranty card and keep it carefully with this manual. Contents 1. PRECAUTIONS ............................................................................................................................... 2 2. SUMMARY OF THE DSC920S

Résumé du contenu de la page N° 3

English 3.CONTROLS [ ] P-M [ ] SS [ ] [ ] DISP BAND [SAT] [ ] CAT [ ] SCAN Names of the Buttons and their Functions [SAT] button [w], [z] button • Used to turn the power on or off. • Used to move the preset channel up or down. • Used to move the category up or down in the [BAND] button Category selection mode. • Used to switch the reception band. • Used to switch the item adjustment or the item • Used to switch the Tuning mode (seek/ in the Adjust mode. (Contrast adjustment, manual) when pressed

Résumé du contenu de la page N° 4

English Display Items Preset channel indication (1 to 6) SAT(satellite) indication Operation status indication BAND PRESET indication indication CAT(category) indication MANU (manual) indication SCAN indication SAT (satellite) indication: MANU (manual) indication: • Lights in the SIRIUS mode, goes off in some • Lights when tuning is performed in the Manual other mode or when the power is turned off. mode. Operation status indication: SCAN indication: • Station names, etc. are displayed. • Light

Résumé du contenu de la page N° 5

English 4.OPERATIONS 3. Press and hold the [a] or [d] for 1 second Turning the power on/off or longer. 1. Press the [SAT] button to turn the power on/ The receiver moves to seek channels below off. or above the current channel and the chan- When the power is turned on, “SAT” is dis- nel found when either button is released is played in the Operation status indication and received. then the display is changed to the channel being received. l Seek tuning Only channels that can be received are sele

Résumé du contenu de la page N° 6

English Operations l Manual memory Receiving stations selected by 1. Select a channel to be memorized. category 2. Press the [P-M] button to enter the Preset 1. Press the [CAT] button to enter the category memory mode. selection mode. CAT indication is light in the display. * The reception channel number (“CH 051”) in the Operation status indication blinks and the 2. Press the [w] or [z] button to select a cat- PRESET indication light. egory. 3. Press the [w] or [z] button to select a pre- 3. Pr

Résumé du contenu de la page N° 7

English Operations Switching the screen saver 1. Press the [SS] button to switch the screen saver. Each time the button is pressed, the screen saver is switched in the order of OFF SS1 SS2 OFF. * If the screen saver is turned on and the button operation is performed, the screen saver mode is released. After information corresponding to the button operation is displayed for 30 seconds, the screen saver displayed is returned. When “OFF” is selected, the display is not lit. (only with backlig

Résumé du contenu de la page N° 8

English 5.INSTALLATION Before Installation Power supply cord connection 1. This set is exclusively for use in cars with a Connect the connection cable securely. negative ground, 12 V power supply. Connect the L-shaped side of the connection 2. Read these instructions carefully. cable to the terminal of the Sirius Satellite Radio (DSH920S). 3. Be sure to disconnect the battery “–” terminal before starting. This is to prevent short cir- Note: For other connections, refer to the Owner’s manual c

Résumé du contenu de la page N° 9

English 2 – ø3.5 Installation of the Control unit n Installing location Dashboard Place the Control unit on the passenger’s seat or stick the Velcro tape (large A) to the center console. * Before sticking the Velcro tape, clean the sticking surface. Velcro tape * Choose a location where the driving of a car is not (large A) hindered and the reception of the signals from the Fig 2 remote control unit is ensured as well (Figure 2). Velcro tape n How to install the Control unit (small B) When ins

Résumé du contenu de la page N° 10

English 10 DSC920S