Instruction d'utilisation Winegard MM-3002

Résumé du contenu de la page N° 1

INSTALLATION INSTRUCTIONS
®
WINEGARD
18" Digital Satellite Antenna
Truck/RV Mount
Model MM-3200 Antenna
Models MM-3084, MM-3002 & MM-3003
ANTENNA/MOUNT MADE IN U.S.A.
U.S. Patent 5,532,710
Elevation
NOTE: The MM-3084 Mount Pipe and
Assembly
MM-3002/3003 Clamp Brackets are not
supplied with MM-3200.
LNBF
18" Antenna
Backup Support
Feed Support
UNPACKING
After unpacking the system, verify that you have the
following: antenna/mount, elevation assembly, feed
support w/LNBF & coaxial cable attached

Résumé du contenu de la page N° 2

ASSEMBLY STEP 1. Attach feed support to the backup support. Feed Support See Figures 1 & 2. Make sure spring is locked into Spring place. Coax Downlead After inserting pin, from LNBF Feed Support swing long part of spring up into the feed support and snap into place under cable clip. E-Clip E-Clip Pin Spring Backup Support FIGURE 2 Backup Support Pin FIGURE 1 Slide elevation assembly into place STEP 2. Remove the two top bolts from the backup support and attach the elevation assembly to antenna

Résumé du contenu de la page N° 3

STEP 3. Attach the MM-3084 (pipe that antenna mounts on) to your truck/RV. If using the MM-3002 clamp brackets, proceed to step 9. If using the MM- 3003 clamp brackets, proceed to step 4. STEP 7. Use (4) 5/16" x 1-1/2" bolts supplied to secure MM-3003 Assembly pipe clamp brackets to side of truck/RV. See Figure 5. Try to maintain as much separation between the STEP 4. Disassemble pipe per number sequence clamp brackets as possible. See Figure 7. It is shown in Figure 4 so that you can sl

Résumé du contenu de la page N° 4

MM-3002 Assembly NOTE: If MM-3002 comes with eight (8) rubber shims instead of the 4 plastic clamp grips. Insert STEP 9. Slip the small plastic shims over the handrail/ rubber shims between clamp brackets and MM- ladder and the large plastic shims over the MM-3084 3001 pipie and handrail/ladder. See Figure 6. pipe. See Figure 6. STEP 10. Attach clamp brackets to pipe and handrail/ ladder using carriage bolts, nuts and washers supplied Slip plastic clamp with MM-3002. Do not crush handrail

Résumé du contenu de la page N° 5

OPERATION STEP 1. Set antenna onto pipe. See Figure 8. Make Elevation Clamp sure elevation clamp fits into keyway on pipe. The Aim antenna in antenna can be secured in place using a small direction of satellite padlock to prevent theft. STEP 2. Connect coax from LNBF to receiver. Optional Attach Winegard exterior cable/TV receptacle (WA-1024) padlock here available for easy coax connection into cab. STEP 3. Connect coax from receiver to TV. STEP 4. Plug in the receiver and TV. STEP 5. Turn TV

Résumé du contenu de la page N° 6

TWO YEAR LIMITED WARRANTY NOTE: The most common problem people Winegard Company warrants this Winegard product experience is moving the antenna too fast. You (excluding receiver) against any defects in materials or must move the antenna VERY slowly so that the workmanship within two (2) year from date of purchase. receiver can acquire and process the digital signal. No warranty claim will be honored unless at the time This takes a few seconds so be patient. After the the claim is made, you pr

Résumé du contenu de la page N° 7

EXPLODED PARTS VIEW (2) 3200377 (6) 2160024 Clamp Bushing 1/4 Flat Washer (2) 2160352 1/4-20 x 1" Carriage Bolt (4) 2160228 1/4-20 Hex Nut 2745342 2745876 Clamp Elevation Frame Bracket Bracket 2160331 3200378 2160220 1/4-20 x 2-1/2" Top Clamp 1/4-20 Nylock Bolt Hex Nut 2160172 (2) 2200089 10-32 x 1/2" Screw 2745875 Knob Elevation Support 2745260 Bracket 46 cm Reflector (4) 2160361 5/16-18 x 5/8" (2) 3140306 Flat Head Bolt Pointer Washer 2240019 Rubber bumper 2160218 10-32 Keps Hex Nut (2) 21601

Résumé du contenu de la page N° 8

EXPLODED PARTS VIEW If you require a replacement part, call Winegard Company at 1-800-288-8094 between the hours of 8:00 a.m. and 3:30 p.m central time, Monday through Friday. Credit card orders only. 2160835 Pin 3200375 Stop Ring 3710290 Rotate Tube 3200376 Elevation Lock (2) 2160289 5/16-18 Nylock Hex Nut (2) 2160027 5/16" Flat Washer (2) 2160286 5/16-18 Square Nut (2) 2200088 T-Handle 3200374 Rotate Bushing (must be assembled onto fixed tube before rotate tube is inserted) 3710285 Fixed Tu