Résumé du contenu de la page N° 1
Résumé du contenu de la page N° 2
inside_front_cover_dishpvr.fm Page 0 Monday, July 9, 2001 1:03 PM FCC RULES WIRELESS REMOTE CONTROL This device complies with Part 15 of Federal Communications Commission (FCC) Rules. Operation is subject to the following conditions: • This device may not cause harmful interference. This device must accept any interference that may cause undesired operation. Unauthorized equipment changes may void FCC certification. IMPORTANT SAFETY INSTRUCTIONS You must keep safety in mind while using this
Résumé du contenu de la page N° 3
text_dishpvr.fm Page 1 Thursday, July 12, 2001 10:02 AM CONTENTS OF THIS USER GUIDE Remote Control Basics....................................... 2 Remote Control Batteries.................................... 2 Remote Control Signals: UHF and IR ................. 2 Remote Control Modes ....................................... 3 Remote Control Setup ........................................ 4 Set Up the Remote Control................................. 4 Scan for Device Codes.........................4
Résumé du contenu de la page N° 4
text_dishpvr.fm Page 2 Thursday, July 12, 2001 10:02 AM REMOTE CONTROL BASICS • This remote control gives you easy access to all the features of a DISH Network satellite TV receiver. Maybe best of all, this remote lets you control DishPVR features. These features let you record audio and video with full digital quality, without a VCR. Also, you can set up the remote to control as many as three devices along with the receiver. These can be TVs, VCRs, DVD players, cable TV boxes, tuners, or audi
Résumé du contenu de la page N° 5
Résumé du contenu de la page N° 6
text_dishpvr.fm Page 4 Thursday, July 12, 2001 10:02 AM REMOTE CONTROL SETUP SET UPTHE REMOTE CONTROL On the next few pages we tell you how to set up the remote to control a TV, a VCR, or other devices. When you get the remote it’s already set uptocontrolthe receiver. But, you must set up the remote to control the TV before you can use the Mute and Volume buttons. To do this, you can either Scan for Device Codes here or Try the Device Codes on page 5. SCAN FOR DEVICE CODES 1. Use the device’s bu
Résumé du contenu de la page N° 7
text_dishpvr.fm Page 5 Thursday, July 12, 2001 10:02 AM Set Up the Remote Control 8. Press the blank Power button to turn the device back on. 9. Try some other buttons to make sure they work. Sometimes, the blank Power button works when other buttons don’t. Note: The mode button for the device starts to flash if you’ve scanned all the codes for that device. TRY THE DEVICE CODES Note: If you just did the Scan for Device Codes,you don’t need to do this. 1. Use the device’s buttons or its remote co
Résumé du contenu de la page N° 8
text_dishpvr.fm Page 6 Thursday, July 12, 2001 10:02 AM CHECK THE DEVICE CODES You can find out what device code you’ve set for each remote control mode. Here’s what to do: 1. Press and hold the mode button for the device, for about three seconds. When all the other mode buttons light up, let go of the mode button. 2. Press the Pound (#)button twice. The mode button flashes the number for each digit of the device code, with a pause between the groups of flashes. A quick flash is for zero. For ex
Résumé du contenu de la page N° 9
text_dishpvr.fm Page 7 Thursday, July 12, 2001 10:02 AM Attach the Remote Control Antenna 4. Use the number buttons to enter any number from 1 to 16, but not the one you found in step 2. The Sat mode button goes out after you enter each digit, and then lights up again. Write down the number you enter _______. 5. Press the Pound (#) button. If the address you enter works, the Sat mode button flashes three times. 6. Press the Record button. 7. This is important: Make sure the Remote Address on the
Résumé du contenu de la page N° 10
Résumé du contenu de la page N° 11
Résumé du contenu de la page N° 12
text_dishpvr.fm Page 10 Thursday, July 12, 2001 10:02 AM REMOTE CONTROL BUTTONS CONTROL THE RECEIVER When you get the remote it’s already set uptocontrol the receiver. But, you must set up the remote to control the TV before you can use the Mute and Volume buttons. Only the buttons we tell you about here control the receiver. Some of the buttons we tell you about here may not control your receiver. Please see the receiver User Guide for info about the receiver’s features. Please remember, the ou
Résumé du contenu de la page N° 13
Résumé du contenu de la page N° 14
text_dishpvr.fm Page 12 Thursday, July 12, 2001 10:02 AM When you have the Browse Banner open, press the up or down arrow button to see the Browse Banner for the next channel. When you have the Browse Banner open, press the right or left arrow button to display the program on now or the next program on a channel. When amenushowsyou alistofchoices,press the up or down arrow button to see more choices. When you have the Program Guide open, press these buttons to highlight a program. To e
Résumé du contenu de la page N° 15
Résumé du contenu de la page N° 16
text_dishpvr.fm Page 14 Thursday, July 12, 2001 10:02 AM Press the Play buttontowatch or to go back to watcha program. Also, press this button to switch from forward or reverse back to watch the program as usual. Press the Recordbuttontostart recordingaprogram. Note: You also use this button if you change the remote control address. Please see page 6. DISH BUTTON You may soon be able to use this button to see the DISH Home. NUMBER BUTTONS Note: The letter groups above some of these buttons m
Résumé du contenu de la page N° 17
Résumé du contenu de la page N° 18
text_dishpvr.fm Page 16 Thursday, July 12, 2001 10:02 AM VOLUME BUTTON Press this button to raise (+)orlower(-) the sound volume. UP/DOWN ARROW BUTTONS Use these buttons to change channels on the TV. SELECT BUTTON The Select button works as the Enter button for a TV. RECALL BUTTON Pressthisbuttontogobacktothe last TVchannel youwatched. Press it againtoswitchbetween the last two TV channels you watched. NUMBER BUTTONS Use these buttons to enter numbers in a TV menu. 16 108933
Résumé du contenu de la page N° 19
text_dishpvr.fm Page 17 Thursday, July 12, 2001 10:02 AM Control a VCR (or a Second VCR) CONTROL A VCR (OR A SECOND VCR) Only the buttons we tell you about here control a VCR. Some of the buttons we tell you about here may not control your VCR. Please see your VCR user’s manual for info about the TV’s features. You can set up the remote to control a second VCR in Aux mode, the same way it controls the first VCR in TV mode. Please see Set Up the Remote Control on page 4. Please remember, the outs
Résumé du contenu de la page N° 20
