Résumé du contenu de la page N° 1
RFX9220M
Installation &
Operation
Installation et fonctionnement
Instalación y funcionamiento
RFX Series
Source Units
Résumé du contenu de la page N° 2
INTRODUCTION Dear Customer, Congratulations on your purchase of the world’s finest brand of car audio source units. At Rockford Fosgate we are fanatics about musical reproduction at its best, and we are pleased you chose our product.Through years of engineering expertise, hand craftsmanship and critical testing procedures, we have created a wide range of products that reproduce music with all the clarity and richness you deserve. For maximum performance we recommend you have your new Rockford Fo
Résumé du contenu de la page N° 3
GETTING STARTED Welcome to Rockford Fosgate! This manual is designed to provide information for the owner, salesperson and installer. For those of you who want quick information on how to install this product, please turn to the Installation Section of this manual. Other information can be located by using the Table of Contents.We, at Rockford Fosgate, have worked very hard to make sure all the information in this manual is current. But, as we are constantly finding new ways to improve our prod
Résumé du contenu de la page N° 4
e l l l g g g n n n u u u j j j e e e h h h t t t f f f o o o s s s d d d n n n u u u o o o s s s s s s o o o L I Q U I D S W O R D I N C i i i c c c i i i v v v • • • PRECAUTIONS Handling the Detachable Faceplate DO NOT drop or cause shock to the faceplate as serious damage may occur. Protect the faceplate by storing it in the supplied carrying case. Avoid Mechanical Malfunction DO NOT grab a disc while it is being automatically loaded into the source unit. Doing this may cause serious damage
Résumé du contenu de la page N° 5
INSTALLATION INSTALLATION CONSIDERATIONS The following is a list of tools needed for installation: Volt/Ohm Meter Hand held drill w/assorted bits Wire strippers 1/8" diameter heatshrink tubing Wire crimpers Assorted connectors Wire cutters Soldering iron #2 Phillips screwdriver Solder Battery post wrench Heat gun This section focuses on some of the vehicle considerations for installing your new Source Unit. Pre-planning your system layout and best wiring routes will save installation time.When d
Résumé du contenu de la page N° 6
Horizontal -20° +20° INSTALLATION Center Console Mounting the source unit in the center console provides optimum access. Be sure the installation does not interfere with the operation of the gear shift or parking brake. Glove Box Mounting the source unit in the glove box is adequate, but does not provide easy access. Glove box mounting should only be done if “Instrument Panel” or ”Center Console,” mounting is not acceptable (i.e., maintaining integrity of older vehicles with metal dashboards.)
Résumé du contenu de la page N° 7
INSTALLATION WIRING THE SYSTEM NOTE: See diagram on following page to help you connect your system. CAUTION: If you do not feel comfortable with wiring your new source unit, please see your local Authorized Rockford Fosgate Dealer for installation. CAUTION: Before installation, disconnect the battery negative (-) terminal to prevent damage to the unit, fire and/or possible injury. 1. Install the 16-Pin Power Harness by connecting the corresponding wires to the electrical and audio system. Solder
Résumé du contenu de la page N° 8
INSTALLATION DO NOT connect optional CD Changer to DO NOT connect optional Wired Remote to this port. SOURCE UNIT FEATURES 8
Résumé du contenu de la page N° 9
SOURCE UNIT FEATURES 1. OFF – Turns the source unit on and off. 2. DISP – Toggles between different display features in main display; when pressed and held for 1 second, toggles clock between hours and minutes. 3. BAND – Selects which bank of tuner presets (FM1/FM2/AM) should be active. 4. MODE – Selects between TUNER/CDP/CDX/AUX1 modes. 5. ENTER – Enables tracks in MP3 mode. 6. OPEN/EJ – Opens the faceplate and ejects CDs from the in-dash CD player. 7. UP ( ) – Selects the next radio station in
Résumé du contenu de la page N° 10
OPERATION – BASIC INITIAL SETUP NOTE: Items shown in () refer to remote control functions. DETACHABLE FACEPLATE The faceplate is detachable as a theft deterrent. To Detach the Faceplate: 1. Press the Open Button to cause the faceplate to slide down and forward. 2. Press the release button on the bottom front edge of the faceplate and slide the faceplate away from the unit. 3. The faceplate bracket will automatically close after 5 seconds. Push To Attach the Faceplate 1. Make sure that the facep
Résumé du contenu de la page N° 11
OPERATION – BASIC VOLUME KNOB/TONE CONTROLS The Volume knob is a multifunction controller and handles the SEL Volume,Tone Controls, and Setup Options, see below. To Control Volume 1. Turn the VOLUME knob (Volume Outside) clockwise to raise volume. Turn Outside 2. Turn the VOLUME knob (Volume Outside) counter-clockwise Remote to lower volume. To Adjust Tone Controls SEL 1. Press the SELECT button (Volume Center) repeatedly to cycle through SUM > BASS > TREBLE > BALANCE > FADER > VOLUME. 2. Turn t
Résumé du contenu de la page N° 12
OPERATION – BASIC • SCROLL ON [SCROLL OFF] — Titles scroll across panel screen. Scroll Off prevents scrolling. • AUX1 IN 0 [+6, –6] — Allows you to boost the input volume of a weak external audio source or diminish a powerful one. Useful for external sources: MP3 players, video games,VCPs, etc. • VDSEL ON [VDSEL OFF] — This is for the low voltage detction.While "ON", if the power voltage to the unit drops below approximately 10 volts, the unit will begin "beeping".Turning this "OFF" will bypass
Résumé du contenu de la page N° 13
OPERATION – BASIC CD or CDX Modes While playing a disc the panel will display the track number and the time played, also the disc number if in CDX mode, unless the default has been changed to TITLE DEFAULT and a disc title has been programmed in. All Other Modes The panel will display the mode AUX1, unless the default has been changed to TITLE DEFAULT and a title has been programmed in. PANEL DISPLAY DEFAULT To set the default, press and hold the DISP button until the hours on the clock begin bl
Résumé du contenu de la page N° 14
OPERATION – TUNER AUTO STORE If you want the Tuner to select the 10 most powerful stations in order of their signal strength and assign them to Preset buttons 1 to 0, you can use Auto Store. 1. Press and the AS button and the Tuner will scan the entire dial. 2. Auto Store will store radio stations independently in the selected tuner bank (FM1/FM2/AM). PROGRAMMING STATION TITLES The name of a Station can be stored in memory using up to 10 characters as a title. See PROGRAMMING TITLES at the end o
Résumé du contenu de la page N° 15
OPERATION – CD PLAYER Basic Operation NOTE: This system will play AUDIO CDs created on a Macintosh NOTE: This system will play CD-R and CD-RW discs. To Play a CD 1. Press OPEN button and the Front Panel will slide open. 2. Insert a CD and the Front Panel will slide closed after 5 seconds. 3. CDP PLAY will auto-select and the CD will begin playing track 1 immediately. Remote 4. Use UP or DN {Down} Button ( or )to change tracks. To Eject a Disc ENT 1. Press the OPEN button, "EJECT" appears on the
Résumé du contenu de la page N° 16
OPERATION – CD PLAYER To Repeat a Track 1. Press the 2/RPT button to to repeat the track currently playing.. 2. To cancel, press the 2/RPT button a second time. Pressing the 1/SCAN or 3/RDM button will also cancel repeat, or pressing and holding the UP or DN {Down} Button ( or ). NOTE: The panel will display RPT until the function is cancelled. Forward/Reverse Press the DN {Down} Button ( ) and the player will take you to the start of the same track as long as that track is more than 10 seconds
Résumé du contenu de la page N° 17
OPERATION – CD PLAYER RFX 8620M CD Changer Operation (Optional Accessory) Magazine Eject 1. Slide door open in the direction shown. 2. Press the EJECT button to release the disc magazine from the CD changer. Slide Door NOTE: The panel will display NO CD, if in CDX mode, then go to AUX1 mode. NOTE: If the front eject button does not work, a manual eject lever is visible through a hole at the bottom of the unit. Move the lever in the direction Manual Eject Eject shown to eject magazine. Loading Di
Résumé du contenu de la page N° 18
OPERATION – WIRED REMOTE (OPTIONAL) RFX MR1 Wired Remote Control (Optional Accessory) CAUTION:To prevent injury and/or damage to the unit and/or vehicle, read and follow all safety precautions. Installation 1. cut a 2" hole into the panel where the controller will be mounted. Light Connection 2. Connect a wire from a source of switched +12V, is on only when ignition key is in “accessory” or “run” position, to the tab on the back of remote.The switched signal is usually taken from the ACC (access
Résumé du contenu de la page N° 19
OPERATION – TITLE PROGRAMMING Programmable Disc Title Memory NOTE: A maximum total of 100 titles can be programmed into the unit. The name of a Station, CD or AUX1 channel can be stored in memory using up to 10 characters as a title. Title Memory 1. Select the mode you are going to be titling, (Tuner, CDP, CDX or AUX1). If in tuner mode, select the station to be titled. NOTE: The disc to be titled must be in the unit, either in CDP or CDX, and selected. 2. Press and hold the BAND button for 1
Résumé du contenu de la page N° 20
OPERATION – MP3 MP3 Player Operation — Basic Playing NOTE: RFX players do not recognize MP3 CDs created on a Macintosh. NOTE: RFX players recognize MP3’s recorded on either CD-R or CD-RW discs. With support for multi-session as well. NOTE: Playability may depend on the type of CD-R/CD-RW used, CD surface condition, CD writer performance and condition and/or software used. For more information, visit our website. To Play an MP3 Disc 1. Press OPEN button and the Front Panel will slide open. 2. Ins
