Instruction d'utilisation Audiovox MM530

Résumé du contenu de la page N° 1

MM530
5.3" LCD HEADREST MONITOR
1
1

Résumé du contenu de la page N° 2

EXPLANATION OF GRAPHIC SYMBOLS CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER (OR BACK) NO SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL The lightning flash with arrowhead symbol, within an equilat- eral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclo- sure that may be of sufficient magnitude to constitute a risk of electric shock. The excl

Résumé du contenu de la page N° 3

IMPORTANT An LCD panel and/or video monitor may be installed in a motor vehicle and visible to the driver if the LCD panel or video monitor is used for vehicle information, system control, rear or side observation or navigation. If the LCD panel or video monitor is used for television reception, video or DVD play, the LCD panel or video monitor must be installed so that these features will only function then the vehicle is in ‘park’ or when the vehicle’s parking brake is applied. An LCD panel

Résumé du contenu de la page N° 4

B. Contents: 1. 1 x Main Unit MM530 2. 1 x AV Adapter Cable 3. 1 x Din-to-RCA Cable 4. 1 x Din Cable Clip 5. 1 x Owner’s Manual 6. 1 x Fan Bracket C. Installation: Front View Top View 1.Installation will vary from vehicle to vehicle, as headrests in vehicles are not standard. 2.This unit is intended for installation by professional installers. 3.The kit consists of the screen assembly, a clam shell housing and 1 key to remove the screen from the housing. 4

Résumé du contenu de la page N° 5

Headrest Mounting: Mounting Monitor Tray 1) Remove the headrest f from the vehicle for easi- est installation. 2) Lay headrest on a flat sur- face. 3) Using a Permanent Marker, mark headrest material along the exterior of the Mounting tray. 4) Remove the Trim Ring and mark an “X” from corner to corner as shown. 5

Résumé du contenu de la page N° 6

5) Using the utility knife, cut the headrest material along the “X” lines. Do not cut the material along the other lines at this time. 6) This will leave you with an “X” cut as shown. 7) Pull the flaps up and cut the foam beneath the material to the proper depth. Cut all four sides of the foam. 8) Using your fingers, tear the foam out of the headrest leaving a recess where the shell will be inserted. NOTE: At this point you will need to install the harness up through the area into the recess.

Résumé du contenu de la page N° 7

9) Lay the flaps of the headrest mate- rial down into the recess and in- sert the Mounting Tray into the re- cess. Check for fit. If it does not fit properly, you may need to remove some more foam. NOTE: The Mounting Tray will need to be secured to the headrest, either by using tie straps, screws, etc... 10) Guide the cable through the side opening of the Mounting Tray and plug it into the Monitor. Make sure the connector locks into place. Insert the Monitor into the Mount- ing Tray and secu

Résumé du contenu de la page N° 8

Fan Bracket Mounting* The monitor can be mounted on a variety of surfaces using the supplied fan bracket. Select a location for the monitor and find a suitable surface to mount the fan bracket. The mounting location* should be as firm, flat and smooth as possible to ensure maximum adhesion. If the area is not flat the bracket can be bent to conform to the shape of the surface. Clean the area thoroughly and make sure that is dry before attempting to mount the bracket. Remove the backing from th

Résumé du contenu de la page N° 9

D. Controls/Indicators/Connectors: Front View 5 678 9 1. AV Input Jack 2. Power Button 3. Source Button 4. Wide Button 5. Fan Bracket Mounting Hole 6. Picture Select Button 7. Volume Down Button 8. Volume Up Button 9. Headphone Jack 9

Résumé du contenu de la page N° 10

Rear View 9. DIN Jack 10. Video (Yellow) 11. Audio Left (White) 12. Audio Right (Red) 13. Red +12 VDC 14. Black Ground 10

Résumé du contenu de la page N° 11

E. Operation: 1. Connect the external AV source output signal (from VCP, DVD, TV etc.) to the AV jacks (Video-yellow, Right Audio-red, Left Audio-white). 2. Press power button (2) to turn the monitor on and off. The backlight- ing for the buttons will illuminate. 3. Press the volume up (7) or down (6) button to adjust the volume level. 4. Press the picture button (5) to adjust the picture quality. The adjust- ments will be shown on the On Screen Display in the following se quence: Color, Brigh

Résumé du contenu de la page N° 12

12 MONTH LIMITED WARRANTY Applies to Movies To Go Mobile Video Products AUDIOVOX ELECTRONICS CORP. (the Company) warrants to the original retail purchaser of this product that should this product or any part thereof, under normal use and conditions, be proven defective in material or workmanship within 12 months from the date of original purchase, such defect(s) will be repaired or replaced with reconditioned product (at the Company's option) without charge for parts and repair labor. A game