Résumé du contenu de la page N° 1
OPERATING INSTRUCTIONS
BEDIENUNGSANLEITUNG
PERSONAL COMPONENT SYSTEM/STEREO CASSETTE TAPE DECK DS-801
OPEN/CLOSE
ON/STANDBY
DS-801
Stereo Cassette Tape Deck
Stereo Cassetten-Recorder
Résumé du contenu de la page N° 2
Introduction UNPACKING AND Congratulations on Your Purchase! FOR U.S.A Your new high fidelity Cassette Tape Deck is designed to FCC INFORMATION deliver maximum enjoyment and years of trouble free service. This equipment has been tested and found to comply Please take a few moments to read this manual thoroughly. It with the limits for a Class B digital device, pursuant to will explain the features and operation of your unit and help Part 15 of the FCC Rules. These limits are designed to ensure a
Résumé du contenu de la page N° 3
READ THIS BEFORE OPERATING FOR U.S.A AND CANADA ........................120 V FOR EUROPE AND AUSTRALIA .......... 230V/240V FOR YOUR SAFETY FOR YOUR SAFETY Units shipped to the U.S.A and Canada are Units shipped to Australia are designed for designed for operation on 120 V AC only. operation on 240 V AC only. To ensure safe operation, the three-pin plug Observe all safety precautions for use of a polarized supplied must be inserted only into a standard AC plug. three-pin power point which is ef
Résumé du contenu de la page N° 4
CONTENTS Introduction UNPACKING AND INSTALLATION ...................................................................................................... 2 READ THIS BEFORE OPERATING YOUR UNIT .................................................................................. 3 Rear Panel Connections ............................................................................................................................... 5 Front Panel & System Remote Controls .................................
Résumé du contenu de la page N° 5
Rear Panel Connections • Do not plug the AC input cord into the AC outlet when plugging and unplugging connection cords. • Be sure to connect the white plugs to the L(Left) and the red plugs to the R(Right) jacks when making connections with the supplied cords. • Refer to the connecting diagram in the operating instructions of Sherwood system receiver RX-801R. LINE CAUTION: TO PREVENT ELECTRIC SHOCK, DO NOT PB REC REMOVE COVER. NO USER-SERVICEABLE PARTS INSIDE. AC INPUT REFER-SERVICING TO QUA
Résumé du contenu de la page N° 6
Front Panel & System Remote Controls Front Panel Controls PERSONAL COMPONENT SYSTEM/STEREO CASSETTE TAPE DECK DS-801 OPEN/CLOSE ON/STANDBY System Remote Controls SLEEP POWER AUX 12 3 MD 45 6 TUNER 78 9 TAPE CD 0 DOLBY C.RESET CD SYNC. REV.MODE EDIT TIME REPEAT RANDOM EON RDS AUTO/MONO TUNING TUNE MODE PROGRAM MEMO SYSTEM REMOTE CONTROL UNIT (only for RX-801R) 6 ENGLISH
Résumé du contenu de la page N° 7
POWER(ON/STANDBY) BUTTON REWIND( ) BUTTON • Press this button to turn the power on and press Press this button to rewind the tape rapidly during again to enter the standby mode. forward playback or to advance during reverse playback. • In standby mode, this unit is not disconnected from the AC mains and a small amount of current is FAST FORWARD( ) BUTTON retained for operation readiness. Press this button to advance the tape rapidly during • For system operation, connect this unit to Sherwood fo
Résumé du contenu de la page N° 8
Before Operation NOTES ON CASSETTE TAPE • Before loading a cassette tape, take up the slack in the PRINCIPLE OF DOLBY B NR SYSTEM tape to prevent it from becoming entangled around the The Dolby NR system functions so that it automatically increases recording levels of medium and high capstan. frequencies when the recording signal level is lower than the specified level(encoding), and automatically reduces the output level to the normal level during playback(decoding). In this way, the tape hissi
Résumé du contenu de la page N° 9
Operations • To use the system remote control unit of Sherwood system receiver RX-801R, first connect the SYSTEM CONNECTOR jack of this unit to that of RX-801R.(Refer to the operating instructions of the RX-801R.) PLAYING BACK A TAPE Turn the power on. ON/STANDBY 1 • Each time the POWER(ON/STANDBY) button is pressed, this unit is turned on or off. Load a tape. OPEN/CLOSE • According to the type of the tape loaded, the 2 corresponding type(normal, chrome) is detected by the auto tape selector. No
Résumé du contenu de la page N° 10
To stop playback. To rapidly advance or rewind the tape, press the corresponding button in the stop mode. 6 7 SLEEP POWER AUX • In case of forward playback(“ ”). 12 3 MD 45 6 TUNER 78 9 CD TAPE 0 SLEEP POWER DOLBY C.RESET CD SYNC. REV.MODE EDIT TIME REPEAT RANDOM AUX EON RDS 12 3 To rewind To advance MD AUTO/MONO TUNING TUNE MODE 45 6 TUNER PROGRAM MEMO ENTER 78 9 CD TAPE VOL 0 DOLBY C.RESET CD SYNC. REV.MODE TUNING VOL EDIT TIME REPEAT RANDOM MUTE TIMER DISPLAY EON RDS AUTO/MONO TUNING TUNE MOD
Résumé du contenu de la page N° 11
RECORDING Load a tape to be recorded. Note • When there is a erase-protection tab, to record on a single side, you should load a tape correctly or select 1 the corresponding tape direction depending on the OPEN/CLOSE tape direction display( : Playback/recording of the back side, :Playback/recoding of the front side). • For your reference, when loading a tape, the side facing up is the front side and the erase-protection tabs of the corresponding sides are as follows: • Be sure the erase-protecti
Résumé du contenu de la page N° 12
In the recording pause mode, press the corresponding PLAY button to start recording. 6 SLEEP POWER AUX 12 3 MD TAPE 45 6 TUNER 78 9 CD TAPE 0 DOLBY C.RESET CD SYNC. REV.MODE EDIT TIME REPEAT RANDOM EON RDS AUTO/MONO TUNING TUNE MODE PROGRAM MEMO ENTER VOL VOL • “PLAY” lights up and recording starts. MUTE TIMER DISPLAY or • If recording is performed, start play on the desired REMOTE CONTROL UNIT RM-404 SYSTEM REMOTE recording source. CONTROL UNIT (only for RX-801R) To temporarily stop recording T
Résumé du contenu de la page N° 13
CD SYNCHRO RECORDING • When the SYSTEM CONNECTOR jack of this unit is connected to that of Sherwood system CD player CD-801, the CD synchro recording can be performed. Do the steps 1~3 in “RECORDING” procedure. 1 • Because CD synchro recording will start from the front side, be sure the erase-protection tab of the front side. • Only when the both of the erase-protection tabs on the tape are in place, CD synchro recording can be performed on both sides. Select the CD as recording source. 2 SLEEP
Résumé du contenu de la page N° 14
Troubleshooting Guide If your unit should not perform as expected, consult the table below to see if the problem can be corrected before seeking help from your dealer or our service organization. PROBLEM POSSIBLE CAUSE REMEDY No power • The AC input cord is disconnected. • Connect the cord securely. • The POWER(ON/STANDBY) button is • Press the POWER(ON/STANDBY) not pressed completely. button to ON. No sound • Unrecorded tape is loaded. • Load the recorded tape. • Incorrect connections. • Make
Résumé du contenu de la page N° 15
Specifications Type ........................................................................................ Stereo full logic cassette deck with Dolby B NR system Track system ............................................................................................................................. 4-track, 2-channel stereo Recording system ........................................................................................ AC bias system (bias frequency : 105 kHz) Erasing system ........
Résumé du contenu de la page N° 16
5707-21050-008-0
