Instruction d'utilisation Whirlpool UXT4036AA

Résumé du contenu de la page N° 1

UXT3030AA UXT4030AA
SERIES
SERIES
UXT3036AA UXT4036AA
To register this
UXT2030AA
SERIES
ECONOMY RANGE HOOD
product visit UXT2036AA
www.broan.com
INSTALLATION INSTRUCTIONS
READ AND SAVE THESE INSTRUCTIONS
! !
INTENDED FOR DOMESTIC COOKING ONLY.


WARNING
WARNING
TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS, TO REDUCE THE RISK OFINURY TO PERSONS IN THE EVENT OF A RANGE
OBSERVE THE FOLLOWING:
TOP GREASE FIRE, OBSERVE THE FOLLOWING:*
1. Use this unit only in the manne

Résumé du contenu de la page N° 2

PLANNING DUCTWORK INSTALLATION (This section for UXT2030AA, UXT2036AA, UXT3030AA, and In more complex ducting situations, a 3-1/4" x 10" rectangular UXT3036AA hoods only. UXT4030AA and UXT4036AA hoods ducting range hood (UXT3030AA and UXT3036AA hoods) can be skip this section and go on to "Prepare the Hood".) converted to a round duct by means of a transition. Begin planning ductwork by deciding where duct will run between the range hood and the outside. For best performance, use the shortest po

Résumé du contenu de la page N° 3

PREPARE THE HOOD - CONT. 3. Remove top or rear electrical knockout. (FIG. 2) 5. (UXT3030AA AND UXT3036AA ONLY). Install damper/duct connector over opening made in STEP 4. Use #8B sheet metal FIG. 2 screws provided. (FIG. 3) UXT2030AA and UXT2036AA hoods ONLY) Install Model 87 damper (purchase separately) over opening in top of hood. FIG. 3 4. (UXT3030AA and UXT3036AA hoods ONLY) Remove duct knockout. Insert screwdriver under edge of knockout, break tabs, and peel knockout back with pliers. (FIG

Résumé du contenu de la page N° 4

PREPARE THE INSTALLATION LOCATION - CONT. WARNING FIG. 6 WHEN CUTTING OR DRILLING INTO WALL OR CABINET, BE CAREFUL NOT TO CUT EXISTING ELECTRICAL WIRING. 3. Use 1-1/4" bit to drill opening for electric wiring. 4. Cut out duct opening in wall or cabinet with saber saw or keyhole saw. 5. Center hood in installation opening and trace keyhole slots onto wood filler strips on cabinet bottom. 6. Screw four #10 x 7/8 wood screws into exact center of narrow end of traced keyhole slots. Allow 3/8" of scr

Résumé du contenu de la page N° 5

INSTALLING RANGE HOOD 6. Strip 1/2" of insulation foam wires. Connect white to white, black WARNING to black, and green to prepared hole with green ground screw TURN OFF THE PROPER CIRCUIT AT THE SERVICE provided. (FIG. 11) ENTRANCE BEFORE WIRING THIS RANGE HOOD. 1. Run electric wiring through hole drilled in wall or cabinet. Split wiring for 6" and install proper connector for type of wire used. FIG. 11 (FIG. 9) FIG. 9 2. Position hood so that: a.) Wiring is routed through knockout opening. (FI

Résumé du contenu de la page N° 6

USE AND CARE SWITCHES WARNING The fan and light are each controlled by a rocker switch. The light ALWAYS DISCONNECT ELECTRIC POWER BEFORE switch has two positions, "ON" AND "OFF". The fan switch has SERVICING RANGE HOOD. three positions - "HIGH", "LOW" and "OFF". ("OFF" is the middle position.) FAN ASSEMBLY Remove filter. Remove two screws holding motor bracket to range FILTERS hood, and unplug fan assembly. Be careful not to allow fan assembly UXT3030AA, UXT3036AA, UXT2030AA, and UXT2036AA to

Résumé du contenu de la page N° 7

SERVICE PARTS Service parts for your range hood are shown (with part numbers). List the hood model number (on spec label located on inside of hood) and the part numbers of all parts being ordered. FIG. 16 3¼" x 10" Ducted Hood Only Ductfree Hood Only UXT3030AA UXT4030AA UXT2030AA UXT3036AA UXT4036AA UXT2036AA Series Series Series 3-1/4" X 10" Ductfree 7" Round Ducted Hood Hood Ducted Hood Key No. Part Number Part Number Part Number Description 1 47001055 47001055 47001055 Outlet Box Cover 2 7061

Résumé du contenu de la page N° 8

Warranty & Service What is Not Covered By These Warranties Warranty 1. Conditions and damages resulting from any of the following: Limited One Year Warranty - a. Improper installation, delivery, or maintenance. Parts and Labor b. Any repair, modification, alteration, or adjustment not authorized by the manufacturer or an authorized servicer. For one (1) Year from the original retail purchase c. Misuse, abuse, accidents, unreasonable use, or acts of God. date, any part that fails in normal home